Відео

Thanks! It is an amazing manual! Very useful manual to assemble my first drone!

I got error when I set in cli....for o3 and v2 goggles error...no osd display

does it work on vista?

can you use the googles in digital or is this purely analog already?

Where are you from bro?

My friend. What name item you use to test the battery for the first time. To check if have leak ?

I have those 1002s in14,000 19, 00 23000 the 19,000. I like the controllability for 1s but the 14000 on 2s rips on the emax blur props 😊

I use a 1100mah 6s 22.8v 120c lipo battery... is it correct? Use motor 1900kv

can i have the backup betaflight config?

Awesome thanks for sharing they STLs !! much appreciated

What the hell dude... I'm all for good videos to help people, but this is just you talking... not getting anywhere.. Just get to the point already!!

Thank you. I purchased a copy which had no instructions. You saved me lots of time. Happy Flying

First off great video, honestly one of the better tutorials for this gear. Second, I have a question about sbus. I have mine wired up exactly like yours however I dont see input on betaflight, what could be the problem? My Rx is bound to radio I just dont see inputs.

Hello,may i ask for the copy of your Tcmmrc build fc data. I have accidentally flashed it and dint have a backup copy😢

Hello, do you still have the copy of the data in the fc? I just flashed my drone and forgot to save the data

Thanks 🎉

do you know if this solution it works also on 4.5.1? because i no have osd

hello bro, a question, I have the same FC but I want to install an ELRS receiver, can I use the TX6, RX6 pads.

Is it possible to use a parallel board or something with this charger? Also the Toothstor one you mentioned won’t work with xt30 will it?

LOTS OF BUFF. but good knowledge. thank you. goggles bit missed on lots of videos

Hi the issue that I’m having is that the display shows but after 5-10 sec it goes away until I unplug and plug batt

HI what GPS module is compatible with this FC?

Great tutorial, any issues with audio sync?

Thanks, I'm gonna get this one

Just a quick question on the elrs antenna mod. On my 2 Mobula 6 2024s the copper wire antenna is not on the pad that yours was on. Even on Happy Models site the picture of the AIO shows the Copper antenna wire where mine is located which is different than where your is. Very Odd

Appreciate your time and effort for this video

Hallo i Wang to ask from your apex Video if 11000kv on 2s are enough on Same Parts you Use in your Video 😅

Hi I build this FPV with F4v3plus FC what GPS module is compatible with this FC and Betaflight? Please help

I have same quad and same super D 😁 good stuff 😉 i put the up and down antenna right behind camera in front. Great spot. In front of the cross bar in aluminum camera mount. Holds perfectly 😁 great signal. Great video explanation. Thanks. I got the yellow peop guards with mine. Great upgrade with the meteor lights. Xing 2205 2500kv motors and Axis flying argus f7 aio 😁 second 1 I've built. 1st one with 3200kv motors was stolen ☹️🤯 it cut out and fell to middle of road and as i was walking over to get it a car stopped and grabbed it 🤯 not cool!!! ☹️ My radiomaster boxer seems to put out enough power for the Gemini unit (super G) setting in goggles tells me great signal 😉

i forgot about this issue, your video saved me again from agony!

suppose to be 8 press nuts, I also only received 7. Also the press nuts pull in when you add the screws... don't drill them out!!

Hi, did you find a solution for dji googles 3 and iPhone 14 pro? Thank you

Can you tell me if this module does output bluetooth telemetry? I can't figure it out.

Battery is wearing a jimmy hat 😂

Dude, did you try Video and TV Cast for android? Ive seen another video on youtube that uses that but no mention if only using home WIFI of tethering a hotspot

Hello! May I ask if these settings might be available to the Goggles 3 together with the V2? I own the V2 and soon ill get the G3. Will this be possible? Thanks!

Hi nice job👌does o3 unit rquires external bec? Or is it perfect to go with the inbuilt 9v pad?

does it work with vice versa?

I am using same hardwares as you listed. And also binded goggle and jumper t lite radio controller. When I turn on the drone its constantly beeping. What I can do to stop that and make it fly?

Why are you calling the people who switched to the goggles 2 suckers? they are so much better than the previous goggles v2.

Speed up your videos

Hi, thank you for the tutorial. Can you please share the link when I can download the table for vtx which you have shared in the video?

So for the TX module USB-C doesnt matter the positioning of the battery connector ?

did you get the current sensor finally to work? myne dident work as well

can you share your antenna .stl please?

Hi Ihave the same FC the problem is when i apply sudden high throttle drone fall out from sky like failsafe why is that ? My thought is the battery which is 3s 25c could it be a problem ?

Hi! Can we do same with goggles 3? And audience on v2?

A quick comment after a frustrating struggle for me. Running DJI 03 controller on a Speedybee 35 with DJI Goggles V2 and DJI FPV Controller 2 and everything was working fine. Then, I got a DJI 03 Moz 7 and used that for a while with the same goggles and controller that I used with the SB35. But then, when I went back to the SB 35 after binding to the Moz 7, all of a sudden the controller inputs quit showing up and I couldn't arm the drone. The same was true for the Moz 7, when I went back to try and arm and fly it. Spend a long time researching, but finally figured out that my UARTs had switched somehow. What ended up working for me, was UART 1 for VTX (MSP + Disp) and UART 2 for Serial Rx. I turned off UART 4 because I'm not using Bluetooth to the phone app. (yet). Finally, THANK YOU for making this video series. I watched it frame by frame while building my Speedybee 35. Great presentation, everything you need and nothing you don't. 🙂

Carbon fiber is bad for you, wear a mask and gloves

Thanks for the FC protector! I'm actually running the Mob6 Eco, and I think I'm going to print one out to protect the VTX chips.