Відео

How are the mosquitoes ?

Currently in the process of replacing mine when I started to tighten in the bolt my engine rotated an inch or two to the right that I remember then i rememebred tigjten the bolt for the engine holder tool. I have not yet to finish the job do you think that's good caused a timing issue on my engine? The moment was very very minimal

Thanks! In principle you solved my problem. The upper exhaust opening needs to be unhindered.

G'day mate, i ran a provent catch can on my isuzu Dmax for about 6 months and was always suspicious of the amount of oil it collected,and also wondered at some of the inconsistensies in the amount it caught, got pissed of with that and took it off and have never looked back since, i went back to the old belief that once you start a motor get it up to proper operating temperature even if you have to do extra kilms to achieve what you need to do, i know its a pain in the arse but in my situation where i live its really paying off, all sensers and air intake pipes, and exhaust lines are free of excess buildup, long story short, every time you use the vehicle get it up to full operating temperature regardless of distance covered, hope this helps.

Since you have the same bike as me, has it had any bad tranny problems? For mine, when I am in third gear and hit the throttle, it feels like it goes into neutral and auto shifts into 4th gear, so I skip through 3rd now. Just yesterday and today when I hit the throttle in 4th sometimes it will have a scraping sound and shake feeling until I release the throttle. Is that tranny or clutch problem?

This is an invaluable video/ lesson for ALL us DYI's I feel you should set up a Go Fund me and let us help you out! Great video!!

3 hours and it's done, old one out new one in with plugs.

I am a 68 year old lady with a Nissan Elgrand and had a friend mount one of these on the side for me. He mounted it above one of the sliding doors which turns out to be great because you can still get into the car behind it and also take down the little window to get your clothes out of the car. I was worried it was going to be hard to put up as I have very bad shoulders but it was so light and easy to do. I was very surprised on how easy the whole thing was to use

Catch can

your too big to be working on that..hope u bought a BOV...

Great review, We have been looking at hybrids but they all seem to have very short draw bars this camper looks a little longer. If you get a moment could you tell me the distance from the face of the box to the centre of the tow hitch? I drive a cab chassis Ute and the tow bar is tucked under the tray somewhat. Cheers

Hearing that diesel lope coming from a land cruiser on a bright sunny beach, makes me question whether or not I, and American, have actually experienced true freedom. 😕🤔

Thanks

Haha! Was on a movie set in Gold Coast. So I pull out the back seat, easy to do. And put in a foldable mattress and it was spacy

I think you 100% nailed it…slow day and needed something dramatic so they created it

I own an ozpig S2 and i love it. so much so that my 2ft firepit and a shedload of cooking accesories are being sold so i can buy a BigPig

I fitted a universal RCC360 kit to my ZD30 Gu Patrol, I'm really not a fan of how much pressure the hoses to & from the catch can put on the plastic crankcase ventilation fittings on both the valve cover and the intake hose, pretty sure if I do some heavy offroading or a long patch of corrugations they're going to crack & snap and the ute won't be driveable with a big hole in the air intake past the MAF. At some point I'm going to have to make a few brackets just to carry the hoses and get them out of the way. And just like you said it makes a bit of a pigsty of the engine bay, the only way I could fit the hoses was to cable tie them to the intake and heater hoses, not ideal. I also have a leaking seal on my valve cover around the #1 injector, its been letting blowby gases leak out and collect oil all over the top of the valve cover and gather as puddles around the injector tops - the only way to replace it is to replace the whole valve cover which sucks - Anyway the point is ever since the catch can's been on it seems like a lot more oil is coming past that seal - to me this suggests that the catch can is increasing the crankcase air pressure, which isn't good..

The sound of that Diesel V8 is glorious. I want one so bad... Good content mate, thanks!

I remember getting into a repeater in South Australia From Seaford Melbourne in those rare conditions.

this fella do remind me of Matt Walsh

this guy reminds me of ben shapiro

your blog can't be opened...

Luv ya work, cheers bloke👍👍👍

well done, top tip. I have been using Staun for near on 20 years and never thought about this, I actually brought two sets. which clearly I didn't need...lol.. Thanks.

Bought the a30m, $160, coming tomorrow

Cheers mate …this’s genius…you’d think the manufacturers would’ve thought of this & etched two permanent marks on each deflator

Thanks alot mate!!! I had same issues the my lockup kit from Richards P2759.

Another scam by Ryco to sell another filter.💲💲💲 All it needed was a stainless screen or wire wool 🤬🤬🤬

Another scam by Ryco to sell another filter.💲💲💲 All it needed was a stainless screen or wire wool 🤬🤬🤬

Mine won't fill! For the life of me I can't figure it out. Installed the outlet onto a tap, hose onto that. Opened the breather turned on the tap and it just airlocks the hose. I can put water in the breather pipe which flows out the tap so it can't be a blockage. Makes no sense!

ua-cam.com/video/GheAHJFtOKk/v-deo.htmlsi=ikYon2q4yBHDZtc0 I call it the horse.

ua-cam.com/users/shortsaJHb5crOG5Q?si=h5GuyDa7h-0XhtCx Mines better. 100mm flew, longer, packs up 3xlengths of 500mm flew pipe inside as well as the legs. Little tip. Drill a 10mm hole into the leges so you can put a screw driver or what ever to undo or tighten the legs.

Who is listening to the emergency channels?

People just don't know how to drive. My 200 is awesome on the beach.

Hi, I am Radio Communication Technician in Png and I am looking for UHF CB Repeaters

Howdy mate , love the video awsome review , just wondering if you have any tips for me , I’ve just installed one into my bt50 , doing my test run on a handheld uniden like yours , I can Cleary here on the hand held from bt50 , but can’t back from the handheld too car .

They are TERRIBLE ON THE BEACH! And your “up grade” from your patrol was a massive mistake

Best car I’ve ever had on the beach turn off all traction control and let tyres down

Very helpful, I'm about to start a half lap with alot of beach and sand driving in WA. Our 2020 MUX did it easy last year but a bigger van saw us upgrade to a 2015 GX 👍

I just bought stauns online today! I can't thank you enough! This is going to save me a bunch of time!

Put proper shoes on, my God those are the same shoes my girlfriend wears

😊 Thank you for sharing!! Exhaust sounds good, could you let me know what system was fitted? Cheers.

Hi mate, found this one really informative. Can you tell me more about the diode you used please? Trying to replicate your setup and struggling to find it

I have just purchased a 2014 VX 200 with 185000 km, it has been run on Penrite Full Synth 5W30 its entire life with 5000 km service intervals. As soon as I pick it up I will be using Castro RX Super . I have used it in a 1HZ Troopy 580000 km, and recently a 2018 RG Colorado 135000 km . Best diesel oil out there in my opinion.

DPF and EGR are terrible for vehicle owners but supposedly good for the environment. Once your inlet gums up and starts using more fuel you are polluting more than ever!!!

Carly sounds like an expensive girlfriend that will only give you the full version with more $$.

Bawhahahahaha 😂😂

Have you tried um Castrol RX Super 14w-40. Also check out the oil API type too, if your motor says to run CI-4 try using the next best CJ-4 which is Castrol RX Super. Then there's the next grade from CJ-4 is the CK-4. Where if you engine used CJ-4 oil the CK-4 can be used. I spoke to some people who have a Hilux the KZN165 models with 450,000kms plus on it and they been using Castrol RX Super, there compression test on the pistons is at 90% which is pretty good.

Hi, xtool A30m is good device, but with it don't have possibility of sevral graph separate on one page and no .csv recording...

very helpful mate thanks!