Відео

Thanks for the detailed tear down. After 30 years I finally tore mine all the way down. It's been a workhorse. It has loaded way more 38, 357, 9mm 45acp than I ever thought I would use. It's now enroute to Dillon as I snapped a chassis mount for bolting to the bench. All covered under their no BS warranty. I am very impressed with their service.

Thank you. This was a big help! I had a powder spill and really needed to deep clean.

Installed my telescoping flag pole . Raised to full height and it is impressive. Went outside late and the LED light was on and shining wonderfully. Will build a military tribute garden around it next. Very fitting that the wife and I installed it on the anniversary of"D" day.

I run a set of 550Cs, one LP & 1 SP. These look like a good investment

Are you running a high pressure load? My gen 3 G22 doesn't seem to produce this issue.

Hi I have the old style RCBS case trimer that takes a different case holder for the various cases in different calibers. Can you swap out a case holder from an old style trimmer with the new universal case holder? Be really cool if you could swap it out. Good video thanks😊

Great review! I found a Corba unit for 29.00 and thought about purchasing it your video helped out a lot. Thanks

Good review, thanks.. I made one 15' DIY and added sand to the inside bottom section because of Texas winds... then additional inside wooden pole, for stiffness.. (as you add sand, water it down,helps pack it)

the more wind , the less flag, as with Storm Flags.... No wounder the pole is giving out. Another thing you could try is stiffening the inside.

Who knew that just a little over 2 years after you did this video that FN would come out with a 10mm that makes the Glock bulge looks like child's play. 🤣🤣🤣

New Subscriber & I rang the notification bell. How many amps did you choose for each of the fuses? You MUST use the Garmin hardwire kit for your Garmin Dashcam to work. Other Brands/aftermarket hardwire kits WILL NOT WORK. Your dashcam will tell you your off brand hardwire kit won't work on the dashcam LCD screen.

Great video

As soon as you said quick process, you can't put it in.

Hello. I have exactly the same press and the problem, that the press ram does not move up exactly centrally onto the die. The joints already have some play. I wonder how a press can have no game after over 30 years? What's the point of cleaning if I still have play afterwards and the stamp doesn't reach the top center. I can't imagine that the press stamp can bend? I took over the press from an old gentleman. What can I do that will center the press

How about "Super Lube" Grease?

I have loaded: 9mm, .38/.357, .45 ACP, .44 MAG... I use Super Lube, Teflon Grease. ( Since 1990-1993... My Cost: $149.95 ) ( Cost of Square Deal, April 2024 : "From $629.00 )

3 way cutter is now $60

I will paint the battery tray..😂

My 2006 Silverado has started leaking fluid too. I bought the reservoir and four hold down snaps..i will try and do the job.. great video..

So did you have to tie into the trigger wire on the back of the radio ? Or did you just hook up the cam feed

Tip for those interested; an easier way to get the Dillon stock spacer out is to push the bolt-end into something hard to compress the squash washer a bit; it then will slide out easily.

Can you provide an update video on this flagpole?

are the dies carbide?

Inherited my late father's RC2 press. Been on it for a few months and saw this video. Thanks, runs soo much smother!

do they sell out of the “ca main “ office? as not far from me, can save a bit on shipping costs. but as on said here are they sill making bullets? in 2024?

Thank you for the honest review!

I load 45acp, so i took an old beat up 45acp deprime/resize die, cut the top of it and drive my empty cases thru it in my press, Works great and cost nothing

I am new to reloading. This video is very detailed and easy to follow. I am researching different trimmers and this video may have helped me make my choice. Thanks, from @firstnaturebackland

boring af!

3 flags in that wind is too much. No flag should be flying in that wind. Just common sense.

Thanks for being so detailed.

Thanks for the video. I pulled my trimmer off the shelf and good lord I'd found I'd had two Dacam reloading tools I'd bought and never used. Well I hooked screwed it in, got the power drill and within minutes I was doing 308 brass at 6 per minute. Thanks for the motivation. Its a great must have tool.

There has been no USA large rifle primers in Australia for 3 years. Pensioners stop shooting because they cant afford factory ammo. There is 1m cci primers on back order. Things are grim.

In-line Fabrication is the only thing you need to know to finish your room. So ends today’s lesson. Cheers!

too many flags for such wind.Its like sailing. Reduce the sails in a storm

Thanks, I couldn’t find what was holding it and it was that darn bolt in the back

Great video and great information

Awesome video. Thanks!

I thought you said you were flying a heavy flag like a heavy duty polyester or a 15’ x 20’ polyester flag that’s made for Highwinds the two ply material or whatever

What brand battery do the Buick 2004 need

Great info. Thanks.

Good video, nice trimmer

You didn't show reconnection water line from pump.

I appreciate your honest reviews. I will say, these are lightweight residential flagpoles and this company really isn’t honest about the wind rating. There is zero chance these poles can withstand 100 or even 70 MPH winds even with the undersized lightweight flag they include. They simply warranty every one that breaks and that keeps most happy enough to not leave bad reviews. They also delete any and all bad reviews and comments on their Facebook. So much so that there was a Facebook page created by someone for others to leave their true negative comments. They are the classic “veteran owned” using that claim to lure people in thinking they’re selling a quality product. For reference, I installed a 30’ commercial internal halyard one piece fiberglass flagpole. That required 15 80 lb bags of concrete! The pole moves less with the 6x10’ flag I fly then these poles do with a lightweight 3x5.

Thank you for making this. Very helpful.

Did you ever find a hack on how to avoid having to tap the tray to keep the primers flowing?

Thanks had to remove terminal while working on the car. They should have had a handle on the one you took out. Was that the original one?

Pilot not collet.

Good video, thanks

I see this was posted 3 years ago and we’ve been Biden’d since but RCBS now wants $60 for the 3 way cutter now. The power adapter is $15 with shipping and I have already ordered it. Thanks for the info.