iPod Nano 6th Gen Battery Replacement From Start To Finish.
Вставка
- Опубліковано 22 тра 2020
- In this video we cover the process to replace the battery in your iPod Nano (6th Gen). Some soldering is required but no need for expensive equipment.
Any inexpensive soldering iron will do the job. The cost for this repair is also inexpensive to do it your self. iPod repairs www.fixitplanet.com
Help Us Grow Support Fix It Planet through Patreon!
/ fixitplanet
Thank You For Your Support!
Tool List
fixitplanet.com/tool-list
Heat Gun
amzn.to/3bT9J7l
Solder
Kester 24-6040-0053 Solder amzn.to/2J9uO21
MULTICORE / LOCTITE 3096525-M SOLDER amzn.to/3mHgOdo
Slolder Stand
Hakko 611-2 Dual Solder Reel Stand amzn.to/3rdhJpH
Flux
AMTECH NC-559-V2-TF Solder Flux - 30cc amzn.to/3pdx1bU
Chipquik Tack Flux no clean in a 30cc amzn.to/3rs3QUG
Solder Wick
Gootwick Desoldering Braid amzn.to/2WAtGrq
Soldering & Hot Air Station
Hakko FX951-66 Full Kit Single amzn.to/3h5Pqoe
Hakko FM-203 Dual amzn.to/2KsD1Pt
Hakko FM2023-02 SMD Tweezer amzn.to/37AW9Dw
Quick 861DW 1000W amzn.to/3mCwLSb
Fume Extraction
Hakko FA400-04 Bench Top amzn.to/3mEInE4
Hakko FA430-KIT1 Floor amzn.to/3mECya3
Snips & Pliers
Miniature Cutters & Needle-Nose Pliers amzn.to/2WzBBFd
Tweezers amzn.to/34yrKUs
Digital Caliper amzn.to/3mDuUg6
Hakko C1390C Omnivise Board Holder amzn.to/3ribDnS
Spudgers & Pry Tools
iSesamo Spudger + Mini iSesamo amzn.to/2KiXwy6
Nylon Spudger amzn.to/2M0Auwt
Metal Spudger amzn.to/3mDV4PJ
Suction Cups amzn.to/2KOFPpJ
Ultra Thin Flexible Stainless Steel Pry Spudger amzn.to/3p6xnRE
Plastic Pics & Glue Cards amzn.to/37DkyZ4
Xacto X3311 N0. 1 Precision Knife amzn.to/3rejYZT
Screwdrivers
Wiha 92093 / 50 Piece Precision Screwdriver Set amzn.to/3rgnzXh
Separate Wiha selections amzn.to/3arccps
"Cheap" 9 PCS Screwdriver Set amzn.to/3rfLFBn
Adhesives & Primers
3M 300LSE Double Sided Super Sticky Heavy Duty Adhesive Tape amzn.to/38q2LDZ
3M Tape Primer 94 PEN amzn.to/3nJwiiC
Cleaners
Isopropyl Alcohol 99.9% (IPA) amzn.to/3pdYvhS
*Branson EC 1 Gallon Concentrated For use With Ultrasonic amzn.to/37IvBAB
*Distilled Water For Use With Ultrasonic amzn.to/34xNgsE
*Mix 100ml Branson EC per 1 Gallon Distilled water.
Ultrasonic Cleaner
Crest P500D 45kHz with Basket amzn.to/34xtdur
Crest P1800H 45kHz With Basket amzn.to/3h5P1Cr
Multimeter
Fluke 15b+ Digital Multimeter amzn.to/3h5Cdfl
Type-C USB Meter amzn.to/3rpMGXR
USB 3.0 Meter amzn.to/3h7ZCMX
Bench Power Supply
Programmable DC Power Supply amzn.to/38o70zX
Microscope amzn.to/3mE66V1
*Fix It Planet is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. As an Amazon Associate I earn from qualifying purchases. - Наука та технологія
Thanks for the vid! You made replacing the battery in my sons nano super easy! Put a smile on the kids face :)
That is awesome!
Thank you for the excellent closeups and instructions!
Thank you man. After I've replaced all correctly my nano didn't get "on" so I couldn't understand why, even after connecting the recharge wire the same. So I firstly thought it was a bad new battery and just welded again an old one to make sure it still works. And fortunalty it was. After that I've welded again a new battery but before closing everythin I've connected the wire for recharge as you did in this video just to make sure it works. Don't know how but I did it !
I watched this vide just because your voice is so soothing!
Really well explained. Thank you!
Excellent video. Thank you.
Snipping the wires was pretty smart, most other tutorials show them removing the whole board to desolder the battery directly.
We are going to have a great day today
Thanks very much for this video. As you said, I am waiting for better times without "Pandemia". Greetings from Costa Rica, Central America.
Very helpful video thanks
hmmm i bet a 501235 3.7V 180mAh battery would fit... its 5mm thick instead of the OG battery which is ~2.5mm, but it doesnt have nearly as much wasted dimensions from the crimp around the parameter and is several years newer design. could probably find those extra 2.5mm by gluing around the battery and either leaving the "metal bracket" off or cutting it across so it doesnt cover on top of the battery. im sure there is a mm or two tolerance by design due to battery expansion.
this simple change would increase the capacity by 80% and also would be much cheaper as a generalized battery source.
Thank you for the video! Excellent quality...
Thank you
Nice
Oui!
Thank you so much !!!!
You're welcome!
guonderful
Great video! So... is there a link to buy a new screen if I maybe went in a little too far? Live and learn!
Good
Thanks
thanks for that video, ive decided im not going to buy a dead batt one now haha
Hi there, just wondering..how much the cost for it.? if you do it for me..what should I do..? Thx..I am from GA :)
I hope you see this. I got this ipod and it's full charge only while plugged in to the wall charger. When its unplugged it turns off. Think changing the battery will help? Thank you
LO SOLUCIONASTE tengo el mismo problema solo conectado prende y lo desconecto y se apaga
How did you know the battery is bad? Maybe the charger?
How do you fix a sensor screen part on the rca viking 10 ?
i got mines a month ago and my battery drains pretty quickly im not sure why it was brand new at most times when i listened to music for like 5 minutes of my workout it dies hope i can get help on this
its cause the stock of these ipod nano 6th gen is very old. they stopped manufacturing these soo many years ago and since then these batteries have been sitting ducks unused which kills the batteries. just replace the battery and you should be fine
What is the 2mm glue tape that you use. Great video btw
You can find a link to some of the adhesive we used here fixitplanet.com/tool-list
I was thinking if we can just skip putting the metal piece in.... Was it necessary like (Heat Sink)... or it is not that important...
It’s there to isolate the screen and it’s wire from the rest of the motherboard
Where could I find a replacement battery for this that was manufactured *recently* (not ten years ago)? I once tried to find a battery for a retired Gameboy Advance (made in 2004). The battery I received LOOKED new...mint in package and still factory sealed. However, it was *manufactured* over ten years ago, so it was already dead before I even bought it.
This iPod Nano is almost 10 years old. Are there any battery manufacturers that still make batteries for old Apple and Nintendo devices? (I’m looking for a Kindle battery as well)
FWIW, this is probably a standard sized battery that's still in production. the GBA SP is a special case, as they put their batteries in... well, a special case. They don't produce the shells any more, but there's now a mod you can do which lets you fit a standard battery into the SP.
@@ActualCharky Thanks! Where can I find that mod, and what is it called? As far as the GBA SP’s battery case, if I could find what went IN the case, I could simply open up one of my dead ones and put the new one that case. But I’d love to find that mod.
@@Vmurph it's generally called the "makho battery mod" after the guy who designed it, but it's basically just a pcb that you solder the cell to so it creates contacts for the SP. You can do it yourself or buy one prebuilt.
Thank you @@ActualCharky!!
Is it worth it to send one in for this? I'm asking this because I have one that needs battery replacement, otherwise it works well plugged in. I don't have the equipment mentioned . :(
You can get the parts and battery on aliexpress for fairly cheap
you can use a blowdryer and something thin to take out the display then use a screwdriver to take out the screws and replace the battery
Mine reboots the ipod but as soon as the home screen comes, it turns off snd again reboots....this happens in a loop ..what is the issue please help
Hey what happened to the metal plate that was removed in the first half of the the video? The metal plate which separated the screen from battery and other pieces. Where you mentioned how tiny the screws were.
We put back in here at 18:46 fussing about it all the way thru.
I can’t seem to get the screen to sit flat without hurting the digitizer. Any ideas?
It doesn't exactly sit flat. I has to pop out a bit
you have to remove the sticker of the battery as it adds a little thickness to it. you can also press/put a little pressure to the battery's circuit so you can align it with its thickness/height. 😊😊😊
What does the primer do? Is it necessary?
BTW this was a really good video. I haven't learned soldering yet but I'd like to.
The primer gives the adhesive a stronger bond.
Excellent!
I have a ipod but it's battery has puffed and the buttons don't click what can I do
Replace the battery.
@@FixItPlanet1 ok thanks
Question is if I replace the battery and screen will I loose my music
You didn't remove the screen protector at the end. 😭😭😭
can i send my ipod nano gen 1 i got a bloited battery and the front is cracked im from philippines can i send it
I just broke my screen... need to be very careful . Now my ipod is going to live with my bose dock .
Pick up the phone