FRANCIS EP.17 | DIY LS Swap Part 3 | Holley Mid Mount Accessory Drive Installation Tutorial
Вставка
- Опубліковано 5 чер 2023
- In this video, I will go step by step how to install the Holley Mid Mount Accessory Drive. This truck is my 1963 C10 named Francis, also known as the “Community Built Truck”.
Parts/Tools mentioned in the video:
Holley Mid Mount Kit: amzn.to/3LfOH5a
Valve Covers: amzn.to/41SkE8D
Valve Cover Bolts: amzn.to/3L7Bx8H
Ignition Coils Gen 1: amzn.to/3mXel53
LS Swap Kit from AZ Pro Performance: azproperformance.com/collecti...
Dirty Dingo Slider Brackets: amzn.to/41Wm2a9
Valley Cover Bolts: amzn.to/3LxfSbr
Budget Headers: amzn.to/3Lsc0s3
Por 15 Chevy Orange: amzn.to/3T5WiF6
ECU Bracket: ebay.us/jFr2Ck
Gasket Kit: amzn.to/3Fh8qxF
Here are a few things that the new website offers (www.simplec10.co)
→ Exclusive Parts for your C10.
→ DIY Tutorials, including my step-by-step "Air Ride Guide".
→ Links to all my favorite C10 parts with reviews!
→ Build Profiles for all my past builds.
→ Simple.C10 Merchandise.
Thank you for your support and encouragement!
→ Become a Simple.C10 Subscriber!
→ Website: www.simplec10.co
→ Instagram: / simple.c10
→ Facebook: / simplec10
→ My Channel Home Page: @simple.c10
→ As an eBay/Amazon Associate, I earn from qualifying purchases.
If the video was helpful, remember to give it a "thumbs up" and consider subscribing. - Авто та транспорт
Well done love the dual snorkel intake the fuel injection looks VERY NICE
Thank you!!
That satin black and red I looking proper 👍
Thanks
Looks awesome
Thanks
Looks sharp! I want that mid mount for my 454
Nice
Glad i was not the only one to have the issue with the AC compressor bolt and the Valve cover. I hope you are going to cover the fuel system setup since i think i am using the same exact setup you are on my C10
I plan to have a video talking through some of the main things to know about this setup.
@@SIMPLE.C10 sweet, looking forward to seeing how you handled the steam port with this intake.
Great video, thanks for uploading. I've looked into a couple "Mid mount drives" doing as much research as possible before buying. That said I have a question. A couple of bloggers spoke about the power steering SQUEALING possible due to the small contact area on only one side pully. Have you had any issues like this? Thank again for the video👍
There was a squeal when I first started the truck but it went away after running. This is by far the most simple and clean mid mount. There are lots of options but not all inclusive and as easy to install. I’ve always wanted this one but I’d be willing to try others now that I’m more comfortable with the swap.
great video how do you know which part number hoses to run from the radiator to the kit? thanks
I bent a clothes hanger the shape I needed it then I went to the parts store and matched it up to a hose. Then cut it to the size I needed.
What DBW to carb plate are you running? I’ve got the mid-mount & classic style intake for my 66 C10 as well.
Lokar classic ls series
We’re did you buy the cooling fan Assembly and the Radiator.
I got this one from az pro performance. It’s a champion LS swap for a 66. I made my own mount on the side so I didn’t have the big bulky radiator clamp. I made it from L channel from Lowe’s. The fan came with it and assembly.
Do you know what radiator hoses you used?
No I don’t. I measured and took a bent cloths hanger to the parts store to find one close.
What hose are you using on the heater hose fittings?
It’s a u shaped hose with two different size ends. I searched Amazon for LS heater bypass hose. Lots of options.
Which model LS engine are you running? Just curious to know if the mid mount and the intake manifold will work on an LM7
This truck is a 5.3 LS1 from a 2004 Suburban.
Thank you
What engine wiring harness and throttle body did you end up using?
I used the painless LS harness and factory 92mm throttle body. If I did it again, I would use Holley terminator.
@@SIMPLE.C10 definitely a good idea on the Holley harness but with them being on back order the painless one ain’t bad till then. Thank you again man keep up the great work!
@stevenaguilera2012 the painless harness was super easy to install. I recommend it but would have liked to go all Holley. At least next time I’ll be able to see the differences.
Hey my friend this kit it will work for a ls1 off of a 2004 corvette?
Yes it should work!
@@SIMPLE.C10 thank you!
where did you route the coil harness
It’s under the intake.
@@SIMPLE.C10 but i don’t see any wires coming out of the valve covers
@@aplomo8910 the coil wires were ran later in. There’s just a single bunch of wires coming out the top. If you go on my Instagram you can find the build photos.
It looks like you added an oil fill in the valley tray..Am I correct in that? If so what did you do. Love this build.
Thanks
John
Actually traded out the valley cover with another one Holley makes with the fill. I should have done that from the beginning because the valve covers require you to take off the cover and one coil pack to add oil.
Thanks so much for the information. I have a 66 C10 that Im thinking of doing an LS3 swap. Just trying to figure out a cost of everything before I take the leap. Im thinking of running a Holley Sniper but unsure of any disadvantage doing it this way.
If there is a private way to share contact info it woukd be great to get your email address ..much easier to communicate that way
Please stop with this "upcoming" stuff. Just release the video when you release it.
Thanks for the feedback. There are a few reasons I do this. Both reasons deal with the way UA-cam processes videos and promotes them. I appreciate your support and hopefully the time I invest in providing this helpful content is worth the wait. I hope you have a great night!
I watch religiously. Do what you gotta do.
I appreciate your support. It means a lot to me!
Are you going to do a review or how to install on that intake?
Yes. I have an install tutorial and also I will do a walk through video of all the parts installed.