Це відео не доступне.
Перепрошуємо.
How To Diagnose Recurrent Dryer Belt Issues: A Deep Dive into Whirlpool Repairs
Вставка
- Опубліковано 19 сер 2024
- If your customer keeps complaining that their dryer is not spinning and you suspect the belt has broken after only a few weeks or months after you did the same repair then perhaps there is something other than the belt at fault.
In this video, we'll examine all the reasons that may weaken a dryer's belt to the point that it will break.
We look into a case involving a Whirlpool dryer that came back with a broken belt after only two months of being returned to service.
Watch Next: Thermal Fuse Keeps Blowing On Dryer • How To Diagnose Clothe...
As an Amazon Associate I earn from qualifying purchases.
Motor pulley and belt: amzn.to/3MHReFW
If you feel like donating:
www.paypal.com...
Send me something:
Harper & Knowles
2945 Highway 1153
Oakdale, LA 71463
My Gear
My Vlog Camera: amzn.to/43vbRv3
My Backup Camera:amzn.to/3UGIz8H
My Studio Camera: amzn.to/417DV5Y
My Wireless Camera Controller: amzn.to/3L4MhWg
My Preferred Memory Card For Cameras: amzn.to/41xIHtc
My Portable Charger: amzn.to/41dtTAc
My Studio Microphone: amzn.to/41fcrLO
My Lavalier Microphone: amzn.to/3UC8Tkn
My Studio Teleprompter: amzn.to/3KJikts
My iPhone Gimbal: amzn.to/3GMLd76
My iPhone Chest Mount: amzn.to/3zZUZ1I
My Main Studio Light: amzn.to/3mvBV8N
My Secondary Studio Light: amzn.to/3GM2v45
My External Hard Drive: amzn.to/3GMLDKI
My Publications
My pen name is Cal Kasheau. Hey, I'd like to shamelessly promote my literary accomplishments while I have your attention. I have several short story titles you can get on Amazon; the links are below. Some are humorous, some reflect events in my life, and some are legends I heard of as a child in the swamps of Louisiana. They are only a dollar or two, and most are free with Kindle unlimited membership. I hope you will take the time to read one or two and give me your honest opinion in the comments on whether or not I should continue to pursue a side gig as an author.
The Legend of the Loup Garou: A Louisiana Horror Story
amzn.to/3EJE4o2
The Legend of the Parlangua: A Louisiana Swamp Tale
amzn.to/3VtF3ys
The Fuzz vs, The Buzz: A Backwoods Beekeeper Meets a Traffic Cop
amzn.to/3EEvwP7
The Story of Buster the Cat: How I survived the Ride From Hell
amzn.to/3T5BM6L
Tell a Story ,Teach a Lesson
amzn.to/3CUd2I3
The Dreaded BMI Index: How it Was that I Went on a Diet
amzn.to/3T5W53Y
My Misadventures as a Moonshiner
amzn.to/3CAmBLT
The Magic Blanket
amzn.to/3yGE8AS
All the Girls I've Loved: A series of stories about a young man's life and the women he loved
amzn.to/3esvIXb
Thanks for watching!
![Дон ДОН, Алаудинов и СБЕЖАВШИЕ из под Курска ахматовцы 😁 [Пародия]](http://i.ytimg.com/vi/dEfCf5IK26Q/mqdefault.jpg)
The problem you described with your friend's dryer was exactly the same problem i was experiencing. The drum would spin with little or no clothes in it, but slowed down or completely stopped with a full load. I changed the motor pulley, and sure enough, it's running great again! Thanks putting up these great videos!
You are very welcome. I’m glad it helped! Thanks for watching!
Thanks Chip! I take in other families’ laundry for a living (about ten loads a day) and my Whirlpool gas dryer has been eating belts left and right-after about 2 months I’m finding the belts shredded and piled around the motor, and the motor pulley is worn smooth. I’ve replaced the rollers every time I replace the belt just to be safe, and the felt seals look great. Most recently I replaced the motor, motor pulley, blower fan, rollers, idler pulley…and this dang thing is grinding and squeaking. The shaft for the left hand roller is grooved, so I get to tear this sucker down again as soon as I receive that and throw it all back together (with, again, a new belt and rollers). Gotta say, it’s been fun learning everything I’ve learned in this process and I can now throw parts on this dryer with the pros, but this is my last attempt-it’s time to look for new dryer! I can’t be down one day every month for repairs. 😂
But this video explained everything I’m seeing, and helped show me I’m not crazy or missing anything else. Keep it up!
Update: got the new axle in, new rollers, put the old motor back in (the new one I got off Amazon was rubbing on the drum 😬), new belt and pulleys….and it’s WHISPER QUIET now, just like brand new! And I’m glad Nan be watching for deals on commercial dryers! 😂
It sounds like you need some commercial machines. Thanks for watching!
The most precise, concise, and informative video on the subject anywhere on the web. Thank you sir!?!
I’m glad you found it useful! Thanks for watching!
Thank you! This helped tremendously!
Thanks for watching!
Appreciate the video. We have a small stackable frigid aire washer and dryer. Well the belt keeps getting stretched out and off the drum. We’ve had it replaced every other week and the technician says it due to overloading. But I’ve kept tabs on the loads and we are doing smaller loads more often with the same issue. These units are used often and I’m sure there’s more that can be done to fix the issue but I keep getting dismissed and they only replace the belt. Now I have a little more of an understanding, to stand my ground.
Belts are made of Kevlar and don’t “stretch out”. I would suspect they are installing belts that don’t fit your machine model (stacked units have shorter belts) or there could be an issue with your idler pulley or motor pulley. The motor/blower assembly could also be loose from the frame. Look inside your door and find the model number and with that search a reputable parts dealer like “Repair Clinic” to get the correct belt part number. Ensure that the service technician is installing the correct belt. If the belts they are replacing aren’t broken or chewed up they are selling you a part you don’t need. Thanks for watching!
All good information
Thanks for watching!
Appreciate all the detail. I replaced a dryer belt, and even though it works, we're getting a burnt rubber smell after more than a month of use. I checked and there's lots of little bits of shredded belt rubber on the motor. I wonder if some problem with the pulley groves that you showed is tearing up the belt?
That may be your problem. I’d check the drum rollers too. If one is seizing up that will make your belt slip and the rubber on the roller will smell too. Thanks for watching and good luck with your repair.
Chip and Brando. Adding another reason:
In my case, kenmore 110168..the front felt a bit old and when drum should seal well it had enough gap for socks and small items get stock. When something goes and gets stuck it will cause it to be be trapped and torn.
Great info. Thank you.
Glad it was helpful!
I have replaced my belt now for three different times and it’s been just fine it dried a whole load of clothes I put the next load in and you hear the belt snap and it keeps breaking them in half what could be causing that?
It’s probably a bad motor pulley. Here’s a link for a new belt and pulley for a Whirlpool made machine. amzn.to/3Qf4Mro If you don’t have this type of machine look inside the door for your model number and use it to order a new pulley for your machine.
Incredibly helpful and enjoyed the tangential stories about working fires as a pilot. Well scripted and edited video
Thanks for those kind words and for watching my videos too!
Thank you.
You are very welcome. Thanks for watching!
Belt looks shredded... what could cause this. Dryer is from 2019
The first thing I would check is a worn out motor pulley. A seized idler pulley can cause this too. I’ve seen on some GE machines that the original belt is very thin, only about three vee grooves wide. I suppose this is a way for the manufacturers to save money. Kind of like the tires on new cars. They only last about 20,000 miles before they are worn out. But, on these machines that thin belt will wear down until the metal grooves in the motor pulley cut right through the belt and shred it. The replacement belts are wider and thicker. Maybe, if everything else checks out, you are a victim of corporate bottom line. Thanks for watching!
Thanks for the tips, I’ve replaced about six or seven belts in the last year. Sometimes only lasting a week. I Totally replaced the pulley and rollers and tensioner idler when the very first belt broke. Wondering if the drum is dragging on the front and back portion of the dryer somehow. Kenmore 500 is the model.
Check the tub glides on the drum and the felt they run on. Be sure the rollers are free and not jammed by hair behind them. If you are using an aluminum motor pulley try changing to one that is steel. Thanks for watching.
Our belt keeps breaking but the metal piece shattered but we repaired both and it shattered again and broke another belt
And we bought a new motor/pulley
I’m not sure what metal piece you’re talking about. Thanks for watching!
Awesome !!!!
Thanks for watching!
What's the problem when you've replaced the wheels, the idler pulley and the moter pulley put your belt is still snapping. I've watched a dozen videos to make sure the belt is on correctly. The belt lasts about a week. I've been through three, hence the replacement of everything. I'm honestly confused because the felt isn't damaged either. Please help! Thanks! The belt seemed to be shredded a bit because there's rubber dust everywhere, and then it's snapped in one place.
Something is causing a severe drag on the drum if the belt is slipping on a new motor pulley. I’d make sure the rollers move freely, the motor pulley is new and the belt is correctly installed on the idler pulley and motor pulley. If the clothes you are loading it either aren’t spun out correctly it will cause a weight overload too. Thanks for watching!
I just bought a new belt for my Amanda yesterday and I attached it and all was working fine then when I loaded clothes into it, it had a burnt rubber smell and after 3 spins it snapped
I'm sorry to hear about the issue with your Amana dryer. Based on your description, there are a few things you might want to check to resolve the problem:
Examine the motor pulley for any signs of damage. If it's worn or cracked, it might need to be replaced.
Ensure the belt isn't slipping off the idler pulley and jamming, which could cause it to snap.
Check if the drum rollers move freely and don't jam. If they're not functioning properly, they might need to be replaced or lubricated.
Lastly, make sure your washing machine is spinning out the clothes effectively before placing them in the dryer. An over-weighted load can cause the belt to slip and burn before the drum starts turning freely.
I hope these suggestions help you resolve the issue with your dryer belt. If you have any more questions or need further assistance, please don't hesitate to reach out. Thanks for watching my channel!
@@HarperandKnowles thank you I will check this tomorrow
Any information on Fisher Paykel dryer DEGX1 that shreds belts. I’ve replaced the idler pulley kit and bearings. Side of belt wraps around motor shaft with groves turned downward.
I would suspect that the motor pulley needs to be replaced, That's almost 100% the reason why belts get shredded. It may look okay but if you compare it to a new one you'll be surprised. Thanks for watching!
I keep having to replace the belt for my magic chef portable dryer because it snaps. I do have a dog so it is likely the hair. I will say that I do start to hear it sound like it is working a bit hard before it snaps again. It first happened within a few months to a year but I now replacing them a few times a year. This last one only last a month. What do you suggest?
Change the motor pulley and rollers. Thanks for watching!
Hey Chip, question for ya. I have a whirlpool dryer and I've been having to replace belts on it left and right. I've replaced that aluminum head on the pulley on it this last time and this last belt lasted a couple of months and just broke today. Thinkin the wife may have just overloaded it, I replaced that belt and it didn't make it 20 minutes and broke in the load she tried to run. Any tips on what I should I look at next? Thank you in advance.
Make sure your drum moves freely on the felt seal on the front. You may have to replace that. Also the rollers have to spin smoothly. You might need new rollers and axles. I usually replace the aluminum pulley with a steel one when I have customers that break belts too often. I get most of the steel pulleys from scrapped machines. Here is a link for one a.co/d/1jFXFtt I think this is right hand thread, it doesn’t say left anywhere and I disremember the correct part number. Many steel pulleys are left hand threads so be sure when you order to watch out for that. Thanks for watching!
Hey, Chip, thanks for uploading these.
I replaced belt, idler pulley, and rollers about a year ago. Well the dryer quit turning. Opened it up and the belt was disintegrated. Replaced belt, checked rollers and pulley. Checked felt gaskets. Now it spins fine and fast empty. But with a load in it will not spin. Seems to be sitting on idler pulley?
Could it be the new idler pulley "spring" or frame is worn already?
Thanks from Texas, Lee.
Amana run-of-the-mill dryer from home depot
I bet your motor pulley needs replacing. If it’s the aluminum kind with the bell on it , it will wear out and shred a belt in no time. Try that and let me know if that works for you. Here is a link for a pulley and belt: amzn.to/3WOXXQ2. Thanks for watch my video!
@Harper & Knowles Washer and Dryer Repair
Hey bud, that was a fast reply!
Upon inspection, the motor pulley does have pitting all throughout the grooves, not to mention smooth spots!
Thanks, Subscribed!
@@leezy7787 that is your problem then. Hey, I don’t let the grass grow under my feet! Johnny on the spot right here! I’m glad I earned your subscription, thanks so much.
On a WP Mod# WED7300XWO Cabrio Dryer, to replace the (drum) “belt retainer”, PN# WP3393657, is/are the belt pulley(s), fore & aft, Left Hand Threads???
Please advise. 🙏
The motor pulley is right hand threads and the blower is left hand thread. The belt retainer isn’t threaded. I hope this helps. Thanks for watching!
Thanks for your prompt & helpful reply!!! 👍🇺🇸👏
@@HarperandKnowles …actually, at least in my case, it’s the drum drive (aft) pulley that’s left-hand thread. The blower drive (fore) pulley is standard right-hand thread.
I thought that’s what I said. The shaft that the blower goes on is left the shaft the belt goes on is right. Oh, wait, I’m sorry I didn’t look up that model number. That model has the flat blower that mounts on the bottom center of the cabinet. I was thinking about the standard Whirlpool models. I apologize for the confusion. I hope I didn’t cause you to break anything!
Maytag centennial will not spin after replacing broken belt.
Is the motor turning? If so examine the motor pulley or your installation. Something is wrong. Thanks for watching!
@@HarperandKnowles motor is on. I switched the belt and pully. No spin.
Is the belt tension tight?
@@HarperandKnowles it is. It starts spinning then stopped when I put the clothes in. Maytag centennial. Wheels spin.
Either something is binding or the belt tension is too loose or the wrong belt or the motor pulley is bad.
No but my dryer drum roller keeps breaking within month of replacing
Did you change the axle too?
After checking it just now, looks to be slightly bent ( axle ) thank you for your reply because you lead me to check my axle!
At what point is worth just getting a new one
I suppose when you’ve had enough aggravation from it and you’re done. Thanks for watching!
@@HarperandKnowles thanks. I am current trying to id my problem . Sounds similar to what you described in the video. First my belt broken, then I put a new belt it. The drier started spinning fine with no load but after some load put in.. it started peeing and the barrel stopped spinning … then I see my new belt is now completely shredded … disintegrated to almost masticated rubber all over the bottom of my drier … I am wondering if it’s the teeth on my motor shaft.. will check it out later tonight but just got my acl surgery done. It’s going to be a challenge
It is most certainly a bad motor pulley unless you failed when you installed the belt and it wasn’t riding on the idler pulley correctly.
@@HarperandKnowles thank you! I just dissembled the support roller on the lower left corner because it wasn’t spinning smoothly. Now it spins smoothly… I also just cleaned everything . I just tested a small load looks like it’s working. However when I try to turn the barrel myself by hand it still has strong resistance..not easy to turn by hand. Is it supposed to be easy to turn by hand? I just don’t want it to break again..
It should be fine. Glad you got it fixed!
Pro
Thanks for watching!
I’ll bet my bottom dollar it’s the drum turning point being too rough and having a problem turning with anything more than a handful of clothes, turning point of the drum needing a good greasing, the belt will be shredded in no time of the drum doesn’t spin
Yep, we cover that in the video. Thanks for the comment!