Відео

Those are regular deore pedals not xt.

What type of wheel is that on your bench grinder? I want a wheel to polish metal, such as aluminum brake calipers, but don't know what wheel I should buy.

where did you buy the replacement of the free hun bushing?

Thanks for the video, I did the same on a crossride FTS-X. Have you ever taken off the freehub again? Because its pressed on, I wonder how to take it off again. There is very minimal play on the casette right now but not zero. Does this mean that I need to tighten the axle nut against the freehub even more (was starting to run rough when tightened more...)? Or replace the bearing washer inside the freehub?

No difference, good problems

huh?? 0...info

Legal demais essa peça é muito importante para a bike

Bedankt voor de info, erg helder en inzichtelijk!

ua-cam.com/video/meErJdr_fUI/v-deo.html

no gloves is crazy 😭

What are the wheels’ spacing?

As suggested on alu frame i will try the stronger JB WELD steel stick. is it still holding up well instead of the original you've used? Thanks

Please Bearing Code

Good vid shit

Nice work. Would this work on a carbon matte black frame? And should I aplly touch up paint before or after these steps ?

What if you do not have a chain tool

So nice ❤️ Love it. I Just bought a trek800. I am not Sure What Kind of Tool I need for the bottom bracket. Which one did you use?

I saw you removed and polished , but how can u prevent the aluminum surface from oxidized?

Great, but cones are easily replaced. What about a pitted hub cup.???

I have Shimano UN55 and just done over 1000 miles and still smooth like new and i ride mainly on road so only little bit dirty and raining condition i try keep away if i can and hoping will last me 10,000 miles finger crossed

There is no hole for me to screw the bolt into but I have the same crank, I’m so confused

yes I saved a lot on labor thank you

Mooi werk! had niet eens door dat je Nederlands was tot ik Marktplaats zag ;)

For years I've been using just a clean cloth with a dab of turps. It worked great sprayed on to the whitewall tyres of my car; brushed lightly with a nail brush and then rinsed off. It never failed! For bike tyres clean off the grime with a cloth dabbed with turps. For me it has worked every time, and no damage to the tyres or rims.

A quick release skewer broke on me two weeks ago and I just recovered from the crash. Thank you for making this video

Qual a medida do rolamento?

Bout je bedoeld een moer

Pronounced ‘Day e tee’

Followed your instructions and it Worked perfectly thanks

Brillante, directo al grano

Hi, Joe. Everytime I search a nice kit of vintage wheels for my ice red 19,5” 1995 Trek Y 22 I come Back to this video of yours. It is really very clear and explains a lot about what Spinergy rev-X-roks carbon wheels really are. I’ m just wondering if those flaws couldn’t be repaired or enhanced before they show a faulty behaviour on the trail. Replacing rivets by pieces of carbon inside of the edges of the spokes, making them a massive piece only in contact with the aluminum edge. Turning my rear v-brake (it was a cantilever one) into a brake disc type with a special holder in the rear could reduce stress on those wheels. Another brand of 26” wheels of the time was SPIN that only made a tri-spoke mountain bike hollow carbon monocoque wheel bonded to aluminum braking surface rims like Spinergy did. By the way the Spinergy wheels for 700C tires could be used on a mountain bike tire ? My best wishes from Brazil.

Thanks for the review. I've just fitted 700x35c Speed Kings on my Merida Scultura Endurance di2. Not tried them out but the bike certainly looks more like a cyclocross now than a road bike. Looking forward to testing them out along with my new ISM seat.

My first 10 speed chain install went smoothly after watching!

Ali express rocks

Wow, rims are strong af. You were cranking on that hub.

Did the restoration not happen?

Nice shoes and socks... 😉

Ok, informative, you need to adapt and be creative, not everyone can afford to buy the entire Park Tool catalog

someone likes projection on his hands

I had some rusty bike wheels that I used Flitz with 0000 steel wool. They look like new now.

It takes me about 16 hours to hand polish two rims. 2 hours a day while drinking beer and 8+ days later I'm done! It takes a lot of time by hand

I can appreciate what this guy did in this video of restoring this bike saddle. Me personally I don’t have those skills so if I find a destroyed saddle, it usually ends up in the trash and I usually just buy a new one because that’s easier. Sadly, but you know when you don’t have those kinds of skills and it’s just easier to replace something then to try to restore something that you know you have no idea how to restore. I mean you’re gonna go for the easiest option and that is Replace it. I mean, if I had those skills, I probably would be restoring more saddles and keeping a lot more saddles out of the landfill, but unfortunately I don’t have those skills so most of the time they just end up in the garbage.

i dont like those side inlays looks like the tyre is worn out. thanks buddy.

from where can I find that aluminium kid to repair my free hub?

I have this bike, but in my country there are no spare parts for such parts and from abroad it will be expensive

duizend maal dank! werd er gillend gek van!

Great Video 🚴🚴🚴

great! I have my first hydraulic rim brake setup and was at a total loss making sense of the service manual. This gives me the missing context, thanks

I have all my parts ready to rebuild mine right now! This video is just what I needed short and concise!

Derailleur problems is without a doubt the most annoying issue on a bike. After you've spent an hour trying to diy it frustration and anger builds. And now, an hour and half into it I'm close to go demo ranch and see how many 300 win mag it takes to cut it in half!