Bernette Serger / Overlocker Threading - Model 134DL
Вставка
- Опубліковано 11 лип 2024
- Threading a Bernette four thread overlocker / serger.
Covers model 134DL and similar models.
This video includes a timed speed run of threading to compare this more traditional serger threading with the Babylock Jet-Air threading system.
0:00 - Introduction.
0:15 - Thread stand and mast alignment.
2:10 - Installing threads and threading mast.
2:58 - Threading top thread guide bar.
4:30 - Upper looper threading.
8:49 - Lower looper threading.
14:16 - Needle threading.
16:58 - Closing covers and preparing for test sewing.
17:57 - Threading speed run.
23:50 - Conclusion.
Start by making sure the thread mast is positioned properly. Thread the upper looper, then the lower looper and then the needles.
This model can be used as either a four or three thread overlocker / serger.
To use the machine in three thread mode, just remove one needle and its thread.
Tools required - Tweezers and scissors or snips.
Troubleshooting:
Make sure to have good needles installed. If you're unsure, replace them with brand new ones.
Check the blades are cutting well. Use several strands of thread and put them under the top blade and turn the hand wheel until the blade comes down and the threads should be cut cleanly. If not, the blades will need sharpening.
Double check the treading and check the tensions.
www.institches.co.nz
www.patreon.com/sewingmachines - Навчання та стиль
I am so happy to watch your throughly comprehensive and clear view of the video. Thank you so much! My overlocker is Bernette 334DS, I hope that will work with the same procedures as your model 134DL. I will be over the moon if I successfully thread my overlocker. Merci beaucoup! :)
Thanks! I bought a used machine and never open it up for 15 years! Now I can try!
Thanks for this great video! I was struggling to get my new to me 134D threaded correctly and your video helped me isolate where I had misunderstood the instruction manual.
Thank you very much from France
Lawdhammercy!
I’m looking at a serger tomorrow very similar model to this one. I don’t think I could ever do it without your video. I will keep you posted. Thank you ever so much for sharing your expertise with all of us ❤️
Glad it was helpful. Thanks.
Your videos have saved me hours of stress!!! thank youuuu
Happy to help!
Thank you so much for teaching me how to thread my machine - it has been in my closet for 8 years because I was too intimidated to try it. Now I love it - THANKS!
Glad it was helpful!
I finally can use my overlocker. It works perfectly with my Bernette 334DS. I am really over the moon this time! Thank you for your video with detailed instructions and easy steps to follow. Thanks a millions!
This was incredibly helpful!! Thank you! I very much appreciate the clear views. I inherited a Bernette 234 and am amazed that there were several differences, but you helped me figure it out! Thank you so much for this video!
Glad it was helpful!
Excelent demostration! Very helpful! Thanks a lot!
Glad it was helpful!
Worked a treat, thank you! I was fast becoming exasperated before watching this.
Glad it helped!
Very good, Marcos : Brazil
Thanks
I bought this exact same overlocker from an op shop in Auckland and was pulling my hair out trying to figure it out. Fancy finding this awesome video from a kiwi. You are a legend!
👍
Thank you so much! I’m looking at this model at the moment and this is the only guide I could find on it :) would you say this would be a good, reliable machine for a beginner?
Hi there, thank you for posting this video. i followed your video and had success but then one of the pieces of fabric i was sewing had a sticker on it and the neddle broke so i tried to replace needle and rethread which i think i have done correctly but now the threads dont make a stitch when I try sew. Any tips to fix?
Can we do hemmer folds with this ?
Dónde podría encontrar la pieza que se pone en el ancora superior, que sirve para anular la puntada de la misma, y remallar con dos hilos.
would you have a service manual for the 334D that i could download? I've got to replace hook gear as it is cracked. Cheers, Andrew
No sorry. You don't really need the service manual for that job. Just take special note of the timings manually and you should be good. Thanks.
Donde conseguir el manual de la Bernette 134D en español?
Cómo conseguir el manual en español de la Bernette 134D
Por favor alguien tiene el manual en español, el manual de la remalladora Bernette 134D? Lo agradecería.
Hi can the spool holder be replaced if one is broken no
Yes, there should be parts available.
Manual de esta remalladora?