Thank you guys at a1 auto. This video helped me a lot. I didn’t know you had to reprogram anything until now. It worked great with my 2002 Nissan Altima with a manual transmission. But I also followed the advice of another person to make the idle go back to normal. When getting rid of the code then you have to unplug the throttle body and the battery- , wait a minute or so plug it all back then put the ignition on On wait 3 seconds, then pump the gas 5 times in 5 seconds then let go of the gas pedal Wait 7 seconds then hold it down for another 10. The check engine will blink then when it stops blinking and stays on let go of the pedal wait 3 seconds and turn the vehicle on. The cars idle should go back to normal. Like 600 - 800 rpms. Thanks again.
Helpful solution to my situation 2005 ultima 2.5, after numerous tries of the car not taking the reset I did 2 things, first I reset the check engine light to get it off : switch ignition on 3 sec, 5 times press accelerator release in 5 sec, wait 7 sec, hold accelerator down 10 sec. Second I disconnected both the negative battery cable and the throttle body harness then reconnected. Afterwards completed all instructions in this video using stopwatch letting it run continuously through steps, being as on time in the seconds as possible and now mine is fixed! Thank you 1A Auto for your super helpful turorials, you are greatly appreciated!
For Nissan Tiida 2007: After CEL becomes solid again release the pedal, start the engine within 3secs and let it idle. If it's still high-rev/pulsating idle, with foot on the brake, shift into Drive. Idle will now go down under 1000rpm. Shift to Park again, and the car will find its regular idle speed (near 650-700 rpm). BTW, thanks for the video.
I had the worst luck and almost gave up and took it the shop. Make sure your codes are cleared. Drive around for a little, stop the car, take keys out ignition for a little. Keep your key in the ignition and do everything in a row and use a stop watch. On the 2nd step, turn on and off quickly instead of counting. Did it like 20 times and having a breathalyzer made it even more difficult 😅
Another important point to note: If the engine is idling too fast (like after the throttle body has been cleaned), then the ECU will NOT perform the programming. Therefore, Nissan says (NTB05-067) to unplug fuel injectors to lower idle speed. For example, on a 4 cyl, unplug #2 & #4 injectors. Do not rev up motor because it will set a code with the injectors unplugged, just immediately do the programming shown in this video and shut it off. Then plug the injectors back in and start the motor to confirm if programming was successful. Good luck, our $10,000 scan tool didn't even list an X Trail.
I had a P0101 code for my Nissan Altima 2012 and I replace my mass airflow sensor, but the code didn’t go away. So I put the original mass airflow sensor back in and Performed the closed throttlebody relearn and so far for a week my check engine light has been off.. Thank you
There's nothing wrong with my 2006 Sentra throttle body, I did exactly like the guy said in the video, in the order he said, and it worked. Idle came up about 2-300rpm, from 500. The service engine light didn't do everything he said, but the idle still came up. Good deal. Thanks.
Thanks I just did the same thing on 2009 Honda Accord I cleaned the mass air sensor and throttle body it was Revved high did this in 5 mins it worked thanks 🙏🏾
I have a question? I have a 2006 G35 sedan and so far I changed the catalytic converters,A/T FR/B solenoid,Transmission Temperature sensor, fresh transmission fluid and filter, MAF , APPS, new battery, and new brake pads, plus fresh oil change and filter. My car symptoms are slip & vdc lights are on at the same time as the check engine light, late gear shifts, hesitant to accelerate from complete stop, RPMs are hesitant when pedal is fully depressed (very sluggish rev ups), reduced power, delayed response when stepping on gas pedal. Ive done the idle relearn procedure many times but its not sticking. Im lost , HELP!
I have a car problem. I have a 2006 automatic Nissan Altima 2.5S. There has been an emissions code, but not for misfire. The cars stutters and jerks sometimes when stopped while in drive or reverse. When I put the car in Neutral, the stuttering and jerking stops. This does not happen at any normal driving speeds, just at idle. What can be the issue?
+@srshwa We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you
i tried this in my altima 2010 but it does not work because my TPMS & AIR BAG & STEERING WHEEL LOCK warning light. is there another solution in my altima? kindly help me because my rpm is 1500 for 2 days now after i spray trhrottle cleaner
Nissan N16 Sunny 2003 I have a problem with RPM - it's completely unstable The Throttle nail has been moved - and the idle sensor has also been moved How do I return the Throttle nail to the original factory position?
I would love to find you guys have a version of this video for a Nissan Sentra 2015 B17 or similar. I will save a bunch of money now that I know better that you don't need a scan computer to perform all of these steps.
+Kaylee Oconnor The P0507 code means the idle control system has excessively high RPM and would not necessarily be fixed by reprogramming the throttle body. We would suggest taking the vehicle to get properly diagnosed. Please let us know if you have any further questions, thank you.
I was interrupted in the sequence while attempting to program idle air and the throttle will not accelerate the engine. Is it necessary or possible to reset or clear the throttle body to do the reprogram procedure again? I've tried starting from the beginning with no change.
I didn't know that you have to repogrammed the throttle body in a Nissan maxima,I tried to reprogram the Throttle body and the airflow sensor, but it doesn't work.The check engine light is on over 5 years now, and if you remove a certain fuse,it goes off.I got the car reved out but soon as the abs light and slip, the car loose it power.It will drive once it is in drive, but it is not revering out. Could you tell me what to do, waiting for your reply ok .
+NightOwl2022 This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c
I need to know the answer to this as well! I tried doing it on my 2012 Altima but had no success. My rpm is currently idling at about 1000 rpm but normally it should be closer to 500. Please let me know if you find any answers, thank you!
@@spectrakid92 Yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you
I have a 2006 nissa Altima 2.5l with a code p2101 to fix is to clean out the throttle body.. do I still need to reset or is that only when you install a new one
+Jesus Moya Thanks for checking us out. While it may not be required to reset this while cleaning or swapping the assembly out, it may be in the best interest to do so, just incase. You can also speak to your local mechanic to see what they recommend. 1aauto.com
@Pretty fly for a WiFi Let's say you get that p0101 code what would you do next? Replace the Mass Air Flow Sensor and then do the relearn procedure since I'm still getting a p0507 code?
I cleaned my throttle body because the car was a pain to start even if it would and now the car won't stay running. I tried the first 2 steps but it keeps dying a few seconds after it starts. Any ideas? I've even disconnected the negative battery cable. Didn't help.
+@MickDundee444 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
3:48 you turns vehicle 'OFF', then turned back 'ON' and started the car. Was that part of procedure, or accident? I've read other Nissan relearning procedures but they don't mention turning vehicle off. Whenever I try to do the relearn, then start the car, there's hardly any accelerator. Car goes limp with very little accelerator. Not sure why :/
+playmobil We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
i am having problems where i just installed the throttle body sensor and reset the battery but yet when i started the car up as the mechanic informed me to do my car is still idling loudly and as i put it in drive it shakes as if its going to cut off and thats how the old sensor did . on top of my car will not drive no higher in speed then 10 miles with my foot all the way down on the peddle .. please help what can i do if you may know i need help. thank u in advance :-(
I have an 02 Altima 5sp manual. We had just done the head gasket and the car started back up, however, the accelerator won't go up past 1500 RPM. Could my throttle body need to be reprogrammed?
Hello Derrick, of course! Feel free to reach out to us and speak to a customer service representative at 888-844-3393. We are happy to assist you with ordering or any questions you may have. +Derrick
i have a 02 nissan sentra 2.5L and tried this a few times, when i would get to the light blinking it would never blink. so after a few tries i went on with the cranking an reving the motor and it seemed to work. an has been doing fine for about a week now.
In a Nissan Sentra 2004 I had to replaced 02 sensor ( the code P1279 show 1 bank 1 air fuel sensor was greater than the maximum allowabe limit) the RPM were find befor I replaced the 02 sensor. Now I can start up the engine just find when engine is cooled. But when the car engine warmes up the RPM drops and when I need to restart the engine the RPM will drop to 0. I get the same code P1279, I went and changed the PCV vale and still the will start the first time and when I truned it off and restrated the engine it has the power but the RPM drop to 0 I have to push the gas pedal 3 to 4 time to get the RPM up. Please help...
+Bella Karam We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
+stuck in time Since there could be multiple reasons why you’re experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. They’ll be able to troubleshoot the problem and tell you what part or parts you’ll need for the repair.
I recently replaced the throttle body on my 05 Nissan Altima 2.5 & a week later the car goes into Limp mode & I get the codes P1126 & P1122 what can I do to fix it ????
+Richard Gonzalez Thanks for watching! Have you checked to make sure your throttle body is getting the correct amount of voltage? Those codes could indicate an issue with power delivery to the assembly. As always we recommend you have a trusted garage take a look at the vehicle to get a proper diagnosis if you are unable to do so yourself! 1aauto.com
I have a 2012 Nissan maxima sv So I keep getting a check engine and traction control light and my car slows down to a stop I cut it off and cut it back on a few mins later works fine but check engine light still on take it to nissan said its my throttle body fixed it fine next week does it again they say its the k&n cold air intake on it making the throttle body clog up but I just can't see how shop manger says its the oil in the filter is this possible?
+Darrell Partin Since there could be multiple reasons why youâre experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. Theyâll be able to troubleshoot the problem and tell you what part or parts youâll need for the repair.
if the idle still run up and down after replace sensor and throttle body and run all steps according procedure of this video, then keep the engine still run , you unpluge the cable of spark plug of #1 and #3....the RPM will go back normal- then, plug back spark plug cable #1 and #3 back. Engine RPM will be OK. Try that.
+Jacek Luszczak This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +R L
I've tried this several times. The 2006 Murano has the Start/Stop button & this procedure does NOT work. I cleaned the throttle body & changed spark plugs. The code "Idle Speed Higher Than Expected" comes & goes. Other than that it runs fine but idles at 980/1040 rpm. Any thoughts? Thanks in Advance. BTW the 3 Liter V6 is a PiTA to change the back 3 plugs isn't it?
Preparation Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment. Battery voltage: More than 12.9V (At idle) Engine coolant temperature: 70 - 100 C (158 - 212 F) Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral) Electric load switch: OFF (Air conditioner, headlamp, rear window defogger) Steering wheel: Neutral (Straight-ahead position) Vehicle speed: Stopped Transmission: Warmed-up (Drive vehicle for 10 minutes.) Procedure 1Perform "2003-2011 Nissan Murano Accelerator Pedal Released Position Learning" 2Perform "2003-2011 Nissan Murano Throttle Valve Closed Position Learning" 3Start engine and warm it up to normal operating temperature. 4Check that all items listed under the topic PREPARATION (previously mentioned) are in good order. 5Turn ignition switch OFF and wait at least 10 seconds. 6Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds. 7Repeat the following procedure quickly five times within 5 seconds. aFully depress the accelerator pedal. 8Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. 9Fully release the accelerator pedal within 3 seconds after the MIL turned ON. 10Start engine and let it idle. 11Wait 20 seconds. 12Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications. Idle speed = 650 ± 50 rpm (in P or N position)
Will this work for a 2005 Pathfinder 4 liter V6? I am having the same trouble. Tried this to no avail... idles at 1500 rpm. Rev the engine it acts like it's going down hits 1100 then back up to 1500. When you drive it is stays 1100 rpm and will surge up to 1500 when your stopping or putting your foot on the brake.
I just cleaned my throttle body and its insane. It idles at about 1,500 rpm’s and once i put it in park the revs go up and down without idling. I did disconnect the negative for about 1 minute and did all three relearn procedures but problem remains. My 2006 pathfinder 4.0L was doing well, just decided to clean it since it was very dirty but worked just fine. Now I feel like an idiot because i have a problem now that never had before! Please any advice is wellll appreciated!!!
As soon as the service engine light stops blinking during the volume relearn try starting your car without putting the key to the off position. You might have to disconnect the negative battery terminal after the idle returns to normal. Worked for my 350z after I swapped the throttle body.
My 07 pathfinder put in a ignition coil Bank 3 but before that I had to replace my alternator and when I replaced my alternator I saw a lot of black residue around my throttle I took a toothbrush and sprayed it with some throttle body cleaner car was idling funny for a while drove down the street it started rocking got back home turned the car off let it sit for like 6 minutes then drove Maybe 30 minutes it seemed like it idled out right then a couple of days later it started misfiring that's when I found out it was the ignition coil Bank 3 I replaced that then Monday the 9th taking my daughter to work dropped her off . Put gas in the then drove off car started acting like it was running out of gas and gas pedal got loose . Car speed was 10 mile or 5 miles an hour was able to park in the mall parking lot. I tried to reset by taken battery connection off for ten minutes. Reconnect then start the car it will run but shaking like it was getting no gas . Then I press the gas pedal it goes to the floor then suv shuts off . Tried a few times same results. Runs like a lawnmower running out of gas. Got the suv towed home got in and car will crank but no ignition and my gas pedal still really loose I got to hook it up to a machine to read the codes I think I have a friend that has one but I'm just wondering before I get it checked out is it my fuel pump that went bad or is it my gas pedal. Oh I also put a bottle of cataclean a few days before the car did what it did. I did that after I replace my ignition coil check engine light went out few days later the initial check engine light cut back on. Took it to O'Reilly's they hooked it up to the sensor it gave catalytic bank 2 codes so the next day I put in a bottle of cataclean . And after I replaced my alternator I put in a bottle of Lucas high mileage fuel treatment do you think the Lucas high mileage fuel treatment and the cataclean did something bad .
working on a 2006 xterra - performing the Idle air volume learning procedure.. after pressing and releasing the accelerator, the light does not blink.. it is solid the entire time.. I have checked my timing multiple times.. tried longer time and shorter time, all the same results. Any suggestions?
This is not the way!!!!! After pressing 5 times wait 10 full seconds and hold accelerator down Utill check engine light flashes IRADICALLY hold until light come on constant start car witchin 3 seconds
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Thank you guys at a1 auto. This video helped me a lot. I didn’t know you had to reprogram anything until now. It worked great with my 2002 Nissan Altima with a manual transmission. But I also followed the advice of another person to make the idle go back to normal. When getting rid of the code then you have to unplug the throttle body and the battery- , wait a minute or so plug it all back then put the ignition on On wait 3 seconds, then pump the gas 5 times in 5 seconds then let go of the gas pedal Wait 7 seconds then hold it down for another 10. The check engine will blink then when it stops blinking and stays on let go of the pedal wait 3 seconds and turn the vehicle on. The cars idle should go back to normal. Like 600 - 800 rpms. Thanks again.
2.5 engine by the way
Does that goes for nissan AD o
07
It works on nissan AD 07 too
Helpful solution to my situation 2005 ultima 2.5, after numerous tries of the car not taking the reset I did 2 things, first I reset the check engine light to get it off : switch ignition on 3 sec, 5 times press accelerator release in 5 sec, wait 7 sec, hold accelerator down 10 sec. Second I disconnected both the negative battery cable and the throttle body harness then reconnected. Afterwards completed all instructions in this video using stopwatch letting it run continuously through steps, being as on time in the seconds as possible and now mine is fixed! Thank you 1A Auto for your super helpful turorials, you are greatly appreciated!
+1adorableone Thanks for your great reply! 1aauto.com
1adorableone holy moly thanks man. It worked what you said and did. Thank you so much. I was getting spooked lol
For Nissan Tiida 2007: After CEL becomes solid again release the pedal, start the engine within 3secs and let it idle. If it's still high-rev/pulsating idle, with foot on the brake, shift into Drive. Idle will now go down under 1000rpm. Shift to Park again, and the car will find its regular idle speed (near 650-700 rpm). BTW, thanks for the video.
I had the worst luck and almost gave up and took it the shop. Make sure your codes are cleared. Drive around for a little, stop the car, take keys out ignition for a little. Keep your key in the ignition and do everything in a row and use a stop watch. On the 2nd step, turn on and off quickly instead of counting. Did it like 20 times and having a breathalyzer made it even more difficult 😅
Would it be the same procedures for a manual trans too?
On the idle air....after pressing 5 times the engine light will not blink after 7 or so seconds...anyone had this problem?
Another important point to note: If the engine is idling too fast (like after the throttle body has been cleaned), then the ECU will NOT perform the programming. Therefore, Nissan says (NTB05-067) to unplug fuel injectors to lower idle speed. For example, on a 4 cyl, unplug #2 & #4 injectors. Do not rev up motor because it will set a code with the injectors unplugged, just immediately do the programming shown in this video and shut it off. Then plug the injectors back in and start the motor to confirm if programming was successful.
Good luck, our $10,000 scan tool didn't even list an X Trail.
+M Barry Thanks for the added tip! Have a great day! 1aauto.com
M Barry what if it goes to 2rpm and back to 1rpm reapeatly at idle?
In which part of this process should you unplug injectors? Or when to unplug back? Thank you.
I had a P0101 code for my Nissan Altima 2012 and I replace my mass airflow sensor, but the code didn’t go away. So I put the original mass airflow sensor back in and Performed the closed throttlebody relearn and so far for a week my check engine light has been off.. Thank you
There's nothing wrong with my 2006 Sentra throttle body, I did exactly like the guy said in the video, in the order he said, and it worked. Idle came up about 2-300rpm, from 500. The service engine light didn't do everything he said, but the idle still came up. Good deal. Thanks.
Thank you! I'm assuming it's the same for 2005 maxima since there is no video for it.
I hope you still look at this. Is it the same procedure for an 02 frontier manual trans?
I have a 2017 Nissan Altima. Is this the same procedure I would have to perform on my 2017 Altima?
Do you have the learning procedure for a Nissan Altima 3.5 se 2007 ?
Or a link to where I can find it
Will this work for a 2011 nissian altima with push button start
I have a 2003 Nissan Altima, I programmed it and it worked, but once I start the car again it unprograms itself again. Any idea why?
I can find how to do it on my 2015 pathfinder wih a push star button. Would it be the same?
Thank you for your video..
Is that mothed suitable for 2012 model nissan altima...??
Does Nissan Rogue 2014 awd sl also has electric body throttle which requires relearning after cleaning?
Is this applicable to old Nissan's? 87 Nissan D21
Gosh, what a process. That's a bunch of steps. Can or should you do this if you have not replaced the throttle body?
Thanks I just did the same thing on 2009 Honda Accord I cleaned the mass air sensor and throttle body it was Revved high did this in 5 mins it worked thanks 🙏🏾
Will this work with a 2001 Pathfinder ?
I have a 2008 nissan altima with push button it still the process to relearn the p2135 code
Are all of these procedures applied to all Nissan models ?
How do you turn the key on then on again ??? Did I miss something
Turn the key on and turn the key on again.
I have a question?
I have a 2006 G35 sedan and so far I changed the catalytic converters,A/T FR/B solenoid,Transmission Temperature sensor, fresh transmission fluid and filter, MAF , APPS, new battery, and new brake pads, plus fresh oil change and filter. My car symptoms are slip & vdc lights are on at the same time as the check engine light, late gear shifts, hesitant to accelerate from complete stop, RPMs are hesitant when pedal is fully depressed (very sluggish rev ups), reduced power, delayed response when stepping on gas pedal. Ive done the idle relearn procedure many times but its not sticking. Im lost , HELP!
How do u get the Allen wrench to stsy inside
I have a car problem. I have a 2006 automatic Nissan Altima 2.5S. There has been an emissions code, but not for misfire. The cars stutters and jerks sometimes when stopped while in drive or reverse. When I put the car in Neutral, the stuttering and jerking stops. This does not happen at any normal driving speeds, just at idle. What can be the issue?
+@srshwa We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Question I just clean the throttle body when I install it back. The rpms and going up and down 1500-2000 any suggestions
Why is doing the same thing
Jesus Moya did u fix it?
Yeah I took it off and cleaned it and put it back in
Roy Guevara took what off?
yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you
Do these procedures work with a 98 Nissan Frontier 2.4L? Because I’ve done these procedures probably 10 times with no luck
Hello sir in the dashboard appear engine service soon
What happens if the throttle plate doesn't move at all?
i tried this in my altima 2010 but it does not work because my TPMS & AIR BAG & STEERING WHEEL LOCK warning light. is there another solution in my altima? kindly help me because my rpm is 1500 for 2 days now after i spray trhrottle cleaner
Nissan N16 Sunny 2003
I have a problem with RPM - it's completely unstable
The Throttle nail has been moved - and the idle sensor has also been moved
How do I return the Throttle nail to the original factory position?
It did work perfectly for me 😊Nissan Liberty 2002
Should I do the same procedure on my 2005 Xterra 4.0l? I just removed the TB for cleaning then this happened, idle RPM is too high!
I would love to find you guys have a version of this video for a Nissan Sentra 2015 B17 or similar. I will save a bunch of money now that I know better that you don't need a scan computer to perform all of these steps.
thank you, took me couple times, dont know why but after third try idle went back to perfect.
Im having the p0507 code come up will this step still work if I just replaced my throttle body
+Kaylee Oconnor The P0507 code means the idle control system has excessively high RPM and would not necessarily be fixed by reprogramming the throttle body. We would suggest taking the vehicle to get properly diagnosed. Please let us know if you have any further questions, thank you.
I was interrupted in the sequence while attempting to program idle air and the throttle will not accelerate the engine. Is it necessary or possible to reset or clear the throttle body to do the reprogram procedure again? I've tried starting from the beginning with no change.
I didn't know that you have to repogrammed the throttle body in a Nissan maxima,I tried to reprogram the Throttle body and the airflow sensor, but it doesn't work.The check engine light is on over 5 years now, and if you remove a certain fuse,it goes off.I got the car reved out but soon as the abs light and slip, the car loose it power.It will drive once it is in drive, but it is not revering out. Could you tell me what to do, waiting for your reply ok .
Will this work on a 2008 Nissan altima 2.5? Thanks
Yes, the how-to video you're looking for is here: +Alfred Revis
Thank you for video. I followed step by step your procedure and applied to my 1996 Nissan Quest, my car is running good. Once again thanks much.
+Mydung Tran Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
What size engine do you have?
Do you have a video of cleaning the throttle body? I have a 2006 Altima 2.5 and there's no videos of cleaning it
+Sean Anderson We do not have a video for this right now, but we'll keep this request in mind for a future video! 1AAuto.com
Will these steps also work for the Nissan Versa?
+NightOwl2022 This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c
Will this work on a 2012 Nissan Altima?
I need to know the answer to this as well! I tried doing it on my 2012 Altima but had no success. My rpm is currently idling at about 1000 rpm but normally it should be closer to 500. Please let me know if you find any answers, thank you!
@@spectrakid92 Yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you
I have a 2006 nissa Altima 2.5l with a code p2101 to fix is to clean out the throttle body.. do I still need to reset or is that only when you install a new one
+Jesus Moya Thanks for checking us out. While it may not be required to reset this while cleaning or swapping the assembly out, it may be in the best interest to do so, just incase. You can also speak to your local mechanic to see what they recommend. 1aauto.com
@@1AAuto thank you for getting back to me so fast.. I love your videos been following 1A Auto Parts for 3 plus years.. thanks again
What happens if you drive it without doing the relearning ?
@Pretty fly for a WiFi Let's say you get that p0101 code what would you do next? Replace the Mass Air Flow Sensor and then do the relearn procedure since I'm still getting a p0507 code?
Thanks for the video. I think it is working. car wouldn't start before. now it does
+Conner CARANNA Glad we could help! 1aauto.com
My 2003 Nissan Pathfinder keeps the check engine light flashing
You can't do this with a scanner?
I cleaned my throttle body because the car was a pain to start even if it would and now the car won't stay running. I tried the first 2 steps but it keeps dying a few seconds after it starts. Any ideas? I've even disconnected the negative battery cable. Didn't help.
+@MickDundee444 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Please how can I correct bad idle on my Nissan maxima 2004 v6 while idle at 1800 on park mode with very high fuel consumption
Happy new year . How can I do Re-learn Nissan note 2007 1.6 automatic transmission . Thanks allot
3:48 you turns vehicle 'OFF', then turned back 'ON' and started the car. Was that part of procedure, or accident? I've read other Nissan relearning procedures but they don't mention turning vehicle off.
Whenever I try to do the relearn, then start the car, there's hardly any accelerator. Car goes limp with very little accelerator. Not sure why :/
Same bro same
How about if I have to start/stop button
+playmobil We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
This works with Nissan Rogue 2018???
+oscar vargas We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
I clean my Nissan qashqai 2010 throttle body and it just mest up high revin... What can I do.... Can anyone help.....
i am having problems where i just installed the throttle body sensor and reset the battery but yet when i started the car up as the mechanic informed me to do my car is still idling loudly and as i put it in drive it shakes as if its going to cut off and thats how the old sensor did . on top of my car will not drive no higher in speed then 10 miles with my foot all the way down on the peddle .. please help what can i do if you may know i need help. thank u in advance :-(
They need a dealership to reset it with. Consult 2 machine
Hi, do you have a relearn for 2006 fx35 throttle body ?
+Brooklyn 4 ever We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com
@@1AAuto Thank you..
Can you do it for 2005 G35 coupe
+Indoorboyz We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c
I have an 02 Altima 5sp manual. We had just done the head gasket and the car started back up, however, the accelerator won't go up past 1500 RPM. Could my throttle body need to be reprogrammed?
+foosblood24 Thanks for watching! If you disconnected the throttle body then you might have to reprogram it. 1aauto.com
So you guys are legit was gonna order some parts but never heard of you guys
Hello Derrick, of course! Feel free to reach out to us and speak to a customer service representative at 888-844-3393. We are happy to assist you with ordering or any questions you may have. +Derrick
i have a 02 nissan sentra 2.5L and tried this a few times, when i would get to the light blinking it would never blink. so after a few tries i went on with the cranking an reving the motor and it seemed to work. an has been doing fine for about a week now.
Me too
Does dis work on qashqai j10?
+PauL1e It does not. We currently do not have this install video for your vehicle. Thanks for checking us out!
@@1AAuto alright, thanks for the answer!
In a Nissan Sentra 2004 I had to replaced 02 sensor ( the code P1279 show 1 bank 1 air fuel sensor was greater than the maximum allowabe limit) the RPM were find befor I replaced the 02 sensor. Now I can start up the engine just find when engine is cooled. But when the car engine warmes up the RPM drops and when I need to restart the engine the RPM will drop to 0. I get the same code P1279, I went and changed the PCV vale and still the will start the first time and when I truned it off and restrated the engine it has the power but the RPM drop to 0 I have to push the gas pedal 3 to 4 time to get the RPM up. Please help...
+Bella Karam We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
For 2004 sentra u have to do additional steps
What steps are those??
I got p0507!!! Quick question my 02 altima got a new engine runs bad from start should i do this??????? No vacuum leaks
+stuck in time Since there could be multiple reasons why you’re experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. They’ll be able to troubleshoot the problem and tell you what part or parts you’ll need for the repair.
how to make nissan altima model 2008 ???2.25
I recently replaced the throttle body on my 05 Nissan Altima 2.5 & a week later the car goes into Limp mode & I get the codes P1126 & P1122 what can I do to fix it ????
+Richard Gonzalez Thanks for watching! Have you checked to make sure your throttle body is getting the correct amount of voltage? Those codes could indicate an issue with power delivery to the assembly. As always we recommend you have a trusted garage take a look at the vehicle to get a proper diagnosis if you are unable to do so yourself! 1aauto.com
I have a 2012 Nissan maxima sv So I keep getting a check engine and traction control light and my car slows down to a stop I cut it off and cut it back on a few mins later works fine but check engine light still on take it to nissan said its my throttle body fixed it fine next week does it again they say its the k&n cold air intake on it making the throttle body clog up but I just can't see how shop manger says its the oil in the filter is this possible?
Do you have a video on how to clean the throttle body?
+Jet Lee We currently do not have an auto repair video on this particular repair. 1aauto.com
What if car won't stay started?
Great video, thank you! Is the reprograming different for the 3.5 V-6??
+Julio Alvarez The computer should adapt to the new throttle body.
1A Auto Parts when you say adapt do you mean automatically? Because I have a g35 with a new throttle body and gas pedal and I get nothing
Is it the same for a manual transmission 2002 Nissan altima 2.5
I need help with da 07 push button model plz
I did this process and it worked fine, but when I get on a hill it lags and has no power ?????
+Darrell Partin Since there could be multiple reasons why youâre experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. Theyâll be able to troubleshoot the problem and tell you what part or parts youâll need for the repair.
hi. how to relearn throttle body for elantra hyundai 2013.
if the idle still run up and down after replace sensor and throttle body and run all steps according procedure of this video, then keep the engine still run , you unpluge the cable of spark plug of #1 and #3....the RPM will go back normal- then, plug back spark plug cable #1 and #3 back. Engine RPM will be OK. Try that.
is it work on nissan qashqai as well?
+Jacek Luszczak This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
Why it is not working on my car otherwise i have pay $80 to reset
How can I relearn on a 2009 Nissan Murano
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +R L
How do u relearn the 2012 Jeep Patriots throttle body
Hello I have same problem I’m trying to many time still is idle is high please help me
I've tried this several times. The 2006 Murano has the Start/Stop button & this procedure does NOT work. I cleaned the throttle body & changed spark plugs. The code "Idle Speed Higher Than Expected" comes & goes. Other than that it runs fine but idles at 980/1040 rpm. Any thoughts? Thanks in Advance. BTW the 3 Liter V6 is a PiTA to change the back 3 plugs isn't it?
RikterZilla did you fix it I have the same problem
How did you fix it? I have the same problem in my 07 Nissan frontier
Preparation
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment.
Battery voltage: More than 12.9V (At idle)
Engine coolant temperature: 70 - 100 C (158 - 212 F)
Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral)
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed-up (Drive vehicle for 10 minutes.)
Procedure
1Perform "2003-2011 Nissan Murano Accelerator Pedal Released Position Learning"
2Perform "2003-2011 Nissan Murano Throttle Valve Closed Position Learning"
3Start engine and warm it up to normal operating temperature.
4Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5Turn ignition switch OFF and wait at least 10 seconds.
6Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
7Repeat the following procedure quickly five times within 5 seconds.
aFully depress the accelerator pedal.
8Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON.
9Fully release the accelerator pedal within 3 seconds after the MIL turned ON.
10Start engine and let it idle.
11Wait 20 seconds.
12Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications.
Idle speed = 650 ± 50 rpm (in P or N position)
Will this work for a 2005 Pathfinder 4 liter V6? I am having the same trouble. Tried this to no avail... idles at 1500 rpm. Rev the engine it acts like it's going down hits 1100 then back up to 1500. When you drive it is stays 1100 rpm and will surge up to 1500 when your stopping or putting your foot on the brake.
+Anthony Jenkins It may be a similar process.
I use the scanner, great video😏
+Philly Dee Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
I just cleaned my throttle body and its insane. It idles at about 1,500 rpm’s and once i put it in park the revs go up and down without idling. I did disconnect the negative for about 1 minute and did all three relearn procedures but problem remains. My 2006 pathfinder 4.0L was doing well, just decided to clean it since it was very dirty but worked just fine. Now I feel like an idiot because i have a problem now that never had before! Please any advice is wellll appreciated!!!
+Javy Munoz You could try to clean it again to see if it fixes the issue. Hope this helps you out!
As soon as the service engine light stops blinking during the volume relearn try starting your car without putting the key to the off position. You might have to disconnect the negative battery terminal after the idle returns to normal. Worked for my 350z after I swapped the throttle body.
Javy Munoz
yeah I know the feeling and I did it with 2 cars. a Altima and g35. almost a truck but safe on that one .
did you manage to fix that problem? I cleaned mine today and im having the same problem
Pedro Aviles did you fix it ?
Didn’t work on my 2004 nissan sentra 1.8 l
My 07 pathfinder put in a ignition coil Bank 3 but before that I had to replace my alternator and when I replaced my alternator I saw a lot of black residue around my throttle I took a toothbrush and sprayed it with some throttle body cleaner car was idling funny for a while drove down the street it started rocking got back home turned the car off let it sit for like 6 minutes then drove Maybe 30 minutes it seemed like it idled out right then a couple of days later it started misfiring that's when I found out it was the ignition coil Bank 3 I replaced that then Monday the 9th taking my daughter to work dropped her off . Put gas in the then drove off car started acting like it was running out of gas and gas pedal got loose . Car speed was 10 mile or 5 miles an hour was able to park in the mall parking lot. I tried to reset by taken battery connection off for ten minutes. Reconnect then start the car it will run but shaking like it was getting no gas . Then I press the gas pedal it goes to the floor then suv shuts off . Tried a few times same results. Runs like a lawnmower running out of gas. Got the suv towed home got in and car will crank but no ignition and my gas pedal still really loose I got to hook it up to a machine to read the codes I think I have a friend that has one but I'm just wondering before I get it checked out is it my fuel pump that went bad or is it my gas pedal. Oh I also put a bottle of cataclean a few days before the car did what it did. I did that after I replace my ignition coil check engine light went out few days later the initial check engine light cut back on. Took it to O'Reilly's they hooked it up to the sensor it gave catalytic bank 2 codes so the next day I put in a bottle of cataclean . And after I replaced my alternator I put in a bottle of Lucas high mileage fuel treatment do you think the Lucas high mileage fuel treatment and the cataclean did something bad .
Will it work for Chevrolet Captiva?
working on a 2006 xterra - performing the Idle air volume learning procedure.. after pressing and releasing the accelerator, the light does not blink.. it is solid the entire time.. I have checked my timing multiple times.. tried longer time and shorter time, all the same results. Any suggestions?
DillysADV after pressing and releasing the pedal 5 times wait 7 seconds then step on it until it happens (no longer than 20 sec)
hello Sir, can you help me on How to Reprogram my New Throttle Body for 2006 Nissan Note, i will be glad thank you
anyone else notice the car smoking at 2:36? mine smokes too
I, MY XTRAIL USED TBI HITACHI.
I CAN NOT DO THE LEARNING
DOU YOU HELP ME?
I'M BRAZILIAN MECHANIC
Can anyone comfirm that this works on a 370z. thanks
mk4 the same as this one???
+Mokoma joseph We currently do not have this part listed as fitting that particular vehicle. Thank you for asking. 1aauto.com
Can’t turn on the car to make it to temperature 😊
This is not the way!!!!! After pressing 5 times wait 10 full seconds and hold accelerator down Utill check engine light flashes IRADICALLY hold until light come on constant start car witchin 3 seconds
The light is off but I still get code p0507