Nissan Electronic Throttle Body (ETB) Re-Learn Procedure
Вставка
- Опубліковано 16 лип 2024
- How to replace that pesky Nissan electronic throttle body? Although this installation seems to be simple plug and play, the following learning procedures are required to get your car running properly: Accelerated Pedal Released Position Learn, Throttle Valve Closed Position Learn, and Idle Air Volume Learn. Complete these 3 small learning procedures and you'll be back on the road in no time!
(Want to know if this Re-Learn applies to your vehicle--check out the listing below)
Where to Buy CARDONE Nissan ETB (Electronic throttle Body): www.cardone.com/where-to-buy
*RE-LEARN PROCEDURE STEPS*
Accelerated Pedal, Released Position Learn
1. Make sure that accelerator pedal is fully released. (1:09)
2. Turn ignition switch ON and wait at least 2 seconds . (1:14)
3. Turn ignition switch OFF and wait at least 10 seconds . (1:17)
(This procedure requires 2 key cycles, so again, ensure the pedal is fully released)
4. Turn ignition switch ON and wait at least 2 seconds . (1:24)
5. Turn ignition switch OFF and wait at least 10 seconds (1:29)
Throttle Valve, Closed Position Learn.
1. Make sure that accelerator pedal is fully released. (1:38)
2. Turn ignition switch ON. (1:39)
3. Turn ignition switch OFF and wait at least 10 seconds. (1:43)
(Make sure that throttle valve moves during these 10 seconds by confirming the operating sound.)
Idle Air, Volume Learn.
1. Ensure the accelerator pedal is fully released. (1:59)
2. Turn ignition ON, do not start engine, then wait 3 seconds (2:02)
3. Next, Fully depress and release the accelerator pedal 5x within 5 seconds (2:07)
4. Wait 7 seconds, then fully depress and hold accelerator pedal. After Approximately 11 seconds, the Malfunction indicator light will switch from steady to blinking. Approximately 9 seconds later, the light changes from blinking to steady once again. (2:13)
5. Fully release accelerator pedal and start the car within 3 seconds. (2:28)
6. Allow to idle. Wait 20 seconds. (2:32)
7. Lightly rev the engine several times, and make sure idle speed is within specification. When vehicle returns to idle, the learn should be complete. (2:36)
HERE IS THE COVERAGE FOR THIS PARTICULAR RE-LEARN PROCEDURE
MAKE MODEL YEAR CYL LITER
INFINITI G35 2003 - 2006 V6 3.5L
INFINITI I35 2002 - 2004 V6 3.5L
INFINITI M35 2006 - 2008 V6 3.5L
INFINITI TRUCKS FX35 2003 - 2009 V6 3.5L
NISSAN 350Z 2003 - 2005 V6 3.5L
NISSAN ALTIMA 2002 - 2006 V6 3.5L
NISSAN ALTIMA 2002 - 2006 L4 2.5L
NISSAN MAXIMA 2002 - 2008 V6 3.5L
NISSAN SENTRA 2002 - 2005 L4 2.5L
NISSAN SENTRA 2003 - 2005 L4 1.8L
NISSAN TRUCKS MURANO 2003 - 2009 V6 3.5L
NISSAN TRUCKS QUEST 2004 - 2009 V6 3.5L
Was this video helpful. If so, make sure to like it, and be sure to subscribe to our channel.
For technical bulletins regarding steering click here: cardone.com/tech-help/
- Website: cardone.com/
- Facebook: / cardoneindustries
- Twitter: / cardoneparts
*Disclaimer*
At CARDONE we cannot guarantee against improper interpretation or application of the information we present in this video. You should always follow the enclosed safety guidelines, consult your OE repair manual for correct specifications when performing any install or repair procedure. Any injury, damage or loss that may result from improper use of tools, equipment, or from the information contained in this video is the sole responsibility of the user, and not of CARDONE Industries. - Авто та транспорт
Working on 2005 Nissan Altima. Replaced throttle body and watched numerous videos and spent numerous hours trying the relearn procedure. Was about to give up when I watched this video. Started completely over, followed this video and got it on the first try. Thanks for the video. There were some videos that had same procedure but this one just explained it better.
I was about to cry not knowing what to do with my car... Found this video, followed the steps 1 by 1 and viola!!! It solved my problem!!!
Thank you so much!!!
We love hearing from our customers who have found our videos helpful, thank you for reaching out!! 😍👌🔧👍
Hello! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
How can i relearn when the engine light is on throwing a P2135?
Can this keep car from turning on. Code P2135 came up before (Tps issueni have been having for a lil while. Car still ran but sometimes i could not start my car normally and have had to crank multiple times or step on pedal and turn on, other times i would have to drive at 20 mph on the speedometer because i was really going 40 mph. 30 mph is really 60mph, 40 on speedometer is actually 80mph to the cops or sometimes revs high or rarely at times, limp mode. Anyway changed to a new throttle body. Car still cranks but ignition wont start this time. Cannot run vehicle to temperature in order to relearn. I have a camshaft code i need to look into. Maybe i just need gas? Can this be why an 05 altima 3.5 se wouldnt crank over. No clicks just wont start. Also, can these codes still be done. Thanks in advance.
this really helped on my 2005 nissan altima, had removed and replaced the throttle body and car started to rev up and down like crazy.. didn't know what had happened, after watching this video and with a lot of patience, I finally program the throttle body. good video
Just did a spark plug change on a Nissan Tiida. Had to remove the intake and throttle body to get to plugs. Decided to clean the carbon out of the throttle body. Put it together and had idle issues. Went thru this procedure and was a great success. Much appreciated.
Bro 😢same here I changed plugs clean carbon and after all fix the response are so slow is this will successfull work
This method worked on my 2007 Nissan Murano. I took off the throttle body last week to give it a clean and after putting it back in, i started having problems with start ups. So i searched on YT and came across your video, followed the instructions and voila, the car started on the first turn, thank you so much for making this video.
Up up down down left right left right b a select start
CONTRA!
You sank my battleship!
Sounds like a Brutality on mortal kombat
30 lives
Contra baby
Worked like a charm! Dropped idle from 1,300 to right around 650. Thanks!
Glad to hear it 👍
Worked great! My idle was high/erratic after dead battery replacement. P2119 code, so I cleaned the TB and did this relearn. Thanks guys!
It worked on my 2002 Sentra se r spec v. Was throwing a code for tps when I bought it, but the throttle body was new. Thanks for the video, it helped me tremendously!!!
I gotta say I'm impressed to say the least. I had an issue with a vehicle of mine 2003 Pathfinder. Kept getting a code for idle air control RPM too high. I knew something was off it was idling around 1200 or higher RPM. Started doing some research and everything pointed to this video and the more I watched this I thought it was complete bogus just seems a little far fetched. Sure enough no kidding this worked and fixed my issue due to me taking the throttle body off and cleaning it I guess threw it off and messed it up well this procedure fixed it right back to perfect idle around 800. Thank you for this video very helpful indeed
MAN THANKS VERY MUCH !U ARE EXTREMELLY HELPFULL AND USEFULL FOR ALL OF US THE MECHANICS PROFETIONALS!
I HAVE ALL THE DIAGNOSTIC EQUIPMENT I NEED BUT I COULDNT SET UP THE P12 PRIMERA THAT I HAD THE THROTLE BODY CLEANED.THE CAR WAS WORKING 1500 REV ON IDLE .THANKS TO U ITS A PERFECT CAR NOW CLEAN MOUTH WORKING 650 AGAIN.
Thanks for this. Helped me alot on my 2003 pulsar n16. I replaced the battery and the car would shut off after starting. I did the idle air, volume learn process and I had to rev the car up at the end when starting. After that the idle fixed itself.
This procedure really works, if you pay close attention to the instructions and have patience, it took 4 trys before it finally worked. You have to be right on with the timing of each countdown, but good luck to everyone that has to do this!!!
Did u do all 3 Procedures
This video proved extremely useful when I cleaned the throttle body on my 2011 Nissan Rogue. It was running very poorly when I restarted it after the cleaning. The steps shown here, when performed properly, solved the issue for me and I could not be happier. The vehicle is running very well now and there is no more 'stumble' at idle when coming to a full stop.
This saved my life 😀😀😀, been looking for lots of videos to relearn process and this is the only working for me on a Nissan Sentra SR 2015 , thank you so much for this video .
Thanks. Took a few trys but ultimately worked for my 04' nissan titan make sure you follow every step to the end even the rev 7 times at the end. Dont get all excited once you see the blinking light your only half way done...!
Thanks for this. I didn't realize I did it wrong on my '13 titan until I saw this comment. I did it right and now it works. I was tearing my hair out trying to find a vacuum leak after replacing my starter and cleaning my original MAF. Replaced the MAF thinking it was bad, intake seals, was about to try a new intake and throttle body next.
@@misterbulgerso you never replaced the throttle body, just did the procedures?
@@bradlee4309 correct
Thank you! My idle was rough after I changed the coils and spark plugs. Had to remove the whole intake and window cowl to get to the back spark plugs, they made this van hard af to work on.
Thanks for the feedback and insight Robert! We hope you connect with us on Cardone’s other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
This worked on my 2008 2 litre petrol Qashqai. Now drives normally and idles at a steady 700rpm.
Thanks Cardone, I'm absolutely delighted!
Here's my story. I'm driving 2006 Almera till one day car's rpm just wouldn't get higher than around 2k rpms, everything sounded/felt fine just loss of power, took it to mechanic/services and it took them one month to diagnose/replace throttle body, when I got the car back, noticed that rpms are jumping up and down when going into neutral, fuel usage increased insanely, idle rpms too high, brought in back to mechanic because we thought it's not adjusted but he failed to do that and I got worried that the service had given me another bad throttle body and I have wasted my money, till I found this video, tried everything myself and got it working properly on the first try!!! So happy now, love u man, good work!
i have the same issue please advise
MVP🤜🏾 was having issues with my MAF sensor, replaced it and cleaned the throttle body and it started reving around 1200RPM. Your steps helped now its revenge at 600-500👌🏾
Thank you! This video saved the day. Other ones on here are a little wrong and misleading. Also hard to follow. Yours was perfect.
Lllllllllllllllllllllllll
Nicely done guys! This fixed my 06 Nissan Quest after the mechanic cleaned the throttle body and the P0507 popped up.
Thank You! These steps worked at the first try, 2005 Frontier idle was high after TB and MAF cleaning.
Thank you for the feed back.
Thank you for the explanation, I have seen this 'procedure' on other videos but all of the steps were combined and not needed once completed. This worked for me the first time , so I made notes in my Haynes manual for next time.
Im still stunned that actually worked 1st time. you saved me a lot of time so thanks.
Worked for my (push to start ) 2011 Nissan Altima 2.5 . Thank you so much , I had cleaned out my throttle body and mass air flow sensor and after putting things back together . I noticed that my throttle body wouldn’t respond well . My car would show me how much gas I had released by stepping on the gas pedal by having the dashboard indicator meter ( 0-60) MPG on dashboard display . When stepping on gas pedal the meter wouldnt go up and when I would let go the meter would rise and drop constantly and finally max out (randomly out of order) . When it would max out i would assume I can lay off from the gas pedal for a bit but instead the car would lose power as I’m driving and than gain power . Like , the torque would set u back going 30mps literally . I knew it was the throttle body , the flap wasn’t opening right and releasing its mixtures at random times making my car to jerk and idle bad . But nomore . I changed my spark plugs , cleaned out the throttle body , air mass sensor , changed the ignition coils and nothing ever fixed the problem . Other you tubers were saying it’s the transmission slipping but no , it wasn’t . Thank you for your help !
How did you do it with the push button?
My 06 Altima 3.5 is having a similar issue. It did sit for a few years so that’s probably part of the issue. But about a week after getting it going, the service engine soon light came on, the code read p0507. The light went off . Drove 3 more days and light came back on..and one night I accelerated from a red light and then the acceleration went out for a second. I continued on and 10 seconds later it did it again. I get home and park it. The next morning the car won’t start and the service engine soon light is no longer on. Later Day it starts up. But a few hours later nothing happens. I notice I have an oil leak as well.
I unplug the battery for a little bit and it starts up, so I plan next morning to bring it in to be diagnosed. But in the morning it won’t start. I recently had the throttle body cleaned but it still won’t start after I turn it off and let it sit for a little bit. You think the relearn procedure will fix it or I’m not finding the right thing to fix?
Omg thank you so much !!! I had very to almost no acceleration speed once I did this and finito! Worked like a charmed !
Just wanted to add that this is an excellent video but just remember to make sure everything is reconnected especially your mass airflow sensor. I went through this procedure numerous times with no success and was absolutely frustrated. I walked away I came back and noticed I never reconnected the mass airflow sensor. Reconnected the sensor and presto problem solved and the relearn was successful. Much thanks to this video. Hope this helps someone out that might be scratching their head thinking they did everything right but I actually forgot something very simple.
Thanks for the feedback and your insight! Be sure to connect with us on Cardone’s other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
Hello Living Big! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
Ho my god ....i really surprised ....i did on my nissan tiida ...now engine working smoothly because of ur video .... thanks broooooo
Thanks for the comment and the positive feedback! We hope you will connect with us on Cardone’s other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
Hello Aju! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
So you didn't replace anything, just did the procedures to fix performance issues?
For my Nissan Altima 2007 2.5 this worked, I tried about 5 different ways before coming to this one. Yes. Thank you sir.
Thank you for your feed back
@@CardoneIndustries will this work on the 2010 sentra? Having exact same problem
So very helpful! Worked on 2004 1.5 petrol Almera.
Muy bien explicado seguí los pasos cómo lo Explica el maestro y con un solo intento lo logré gracias a Dios muy contento gracias
es el unico que explica el porque y para que de cada cosa, los youtubers de latam nomas te dicen haz esto y esto y lo otro jajajaja y me creia exceptico mañana lo intentare a ver que sale
WOW THANK YOU! I SPEND 1 YEAR TRYING OTHER CODES GIVEN IN OTHER VIDEOS AND NOTHING WORKED! Obviously REPLACING THROTTLE BODY & AIR FLOW SENSOR, ETC., WAS TOO EXPENSIVE!! I HAD TO DRIVE MY CAR TO WORK LIKE THAT EVERY DAY, HURTING MY TRANSMISSION! BUT IT DOES STILL WORK! I ALMOST GAVE UP...UNTIL I FOUND YOU🙏👼👍😀 the shortest of all steps! and IT WORKED!! I WAS IN DISBELIEF! I LITERALLY CRIED! YOU SAVED MY CAR AND I 😉THANK YOU & THANK YOU AGAIN! BLESSINGS!
PS. I LOVE YOU!!!!💕💕 NOW I CAN REST! I CAN SLEEP! & BE AT A LIGHT, OR PARKED WITH MY ENGINE RUNNING! 😀 WITHOUT EVERYONE LOOKING AT ME BECAUSE MY CAR WOULD BE SO LOUD! IT WAS AWFUL! THANKS TO YOU IM NORMAL AGAIN!...well my Nissan is normal again! 🙏👍😀
So you never replaced anything, just tried the procedures to try and resolve performance issues?
Hey I did this last night and it worked. Thank you
Thank you so much for making this video! It worked for my 07’ Nissan Frontier v6 4.0 when I did my engine swap! Idle dropped down rite where it should be after following this video.
Thanks for the comment and the compliment! We love hearing when our videos help with DIY repairs!! Be sure to connect with us on Cardone’s other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
100% working i go through the instruction and my rpm came to normal on my nissan xtrail....thank you sir
I did with my xtrail but didn’t work y
Awesome! I did this even after changing the mass airflow sensor! Worked perfectly! Thanks 🙏🏼
Hey Brian, thanks for the positive feedback! We love hearing about how our videos help our customers!! We hope you will check out Cardone’s other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
Hello Brian! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
I 6th/ forums forums 758@@CardoneIndustries550.00 😅5487
Ahhh I just changed the MAF and cleaned the throttle body, but now I have a lean code and high idle... I'll try this
This is the best video on this test process by far!!!!! Don’t listen to anyone but this guy!!
Thank you very much for the precise step by step video. I would like to add on to this procedure as most batteries are below 13 V, so I if you can connect a booster cable with another vehicle then your voltage should be around 14.5V. Then try to relearn, mine worked the first time after I had 4 failed attempts without a booster connection.
Straight forward, clear and concise. Thank you!
Thanks for the positive feedback Rod, much appreciated! Be sure to connect with Cardone on our other social channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
Hello Rod! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
very professional.. that's perfect.. excellent protocol.
THIS WORKED. Long story short, customer car was idling high I cleaned throttle body and intake during spark plugs replacement. No big deal if if idle high because I've recalibrated throttle body with my scan tool. This time it was a no go! On a 2002 maxima, car idle at 950. Followed steps and mainly final procedure, issue fixed!
Come to find out, it always ran high like that! Well it's fixed now
Awesome vids!!! The same step if you have a KEYLESS START... Just press the button simultaneously as if you are turning a key... It works on my 08 Altima SL in ONE TRY... :D
Thanks. I was looking for an answer for push button start. Much appreciated
Thanks ,man this exactly what I needed!!
2013 Titan... Worked for me! (So far no more lean codes anyway... Stand by). I pulled the intake to replace the starter... Pcv valve exploded last summer so had a mess to clean, noticed the intake tube was ripped under the throttle body hose clamp. Cleaned it all up, replaced the leaky tube, replaced MAF, cleaned the TB/replaced all the gaskets... Still running like crap. Transmission shift points were all screwed up too. I was scared i had cracked the intake or broke a sensor wire pigtail... Was tearing my hair out checking for vac leaks. Its amazing how the computer can correct for all of the messed up parameters this thing had. Im sure all of the tables were now all out of whack correcting for these problems. I never saw a dip in fuel mileage and it idled fairly smooth but was just starting to feel a tiny bit rough... Now that its fixed up i just badly freaked it out changing all this stuff at once. Now it shoukd run like brand new. If only i had somewhere i needed to drive to today lol...
Great video, helped out a lot, my car is a 2005 Altima, was running rough for 2 years red-lights. My steering wheel would shake, I've since cleaned the throttle Body and preformed this re-learn. Seems to run better so far.
Nigel Graham
Did it this weekend, took me only 2 tries... Thanks a lot!!!
Worked like a charm on my 2006 Nissan Quest. Thanks a lot!
How many miles
@@migoyt9127 Just hit 110k.
Great tutorial brother!
Took me two attempts but nailed it.
Works great now.
Glad to hear it, Gonzo!
Wow. This is worked! I was struggling for more than one month with this problem. What a miracle. Dropped idle from 1800 to right around 800!!! Excellent! Many thanks. (This is Nissan TIIDA)
It works perfectly on Nissan Bluebird G11 (Sylphy) 2005 - 2006 models. Just checked!!!
July 14, 2024
Wow it worked!!
Had to do it like 4 times.
It was idling high all the time. Nowit's normal! Yaaaay!
Did you have to erase codes ????
@@eleazarlanda9122
Nope
Did you change the Throttle Body???
@@eleazarlanda9122
No.
@@eleazarlanda9122
Car was idling high when I first bought it. It had 160k miles. Not sure if previous owner changed anything. (I doubt it). Maybe battery or ecu or something electrical
This works on a 1.8L 2005 Sentra. After trying this method many many times with zero success, I changed a couple of things.
1. I used my torque app and OBD dongle to constantly check and erase any ses codes while the car was running and during this idle learn. My car would set the high idle code many times but it takes time before the ses light comes on to let you know. So you think there's no code set...but its in the computer even so. Keep that code clear regardless of any dummy light.
2. After this process was done I idled it 5-10sec then placed into drive and back to park twice. It almost killed in drive doing this but I put I back in park and idle settled out.
Success!
Thanks this was so informative
Thanks. It worked after a couple tries
Glad to hear
Wah, great, selfless proper guide to Relearn... Thank u so much, but alittle too fast... ☃️☃️☃️☃️
I can't believe this actually worked but it did, thank you
What year Nissan?
@@davonteelse7163 2005 Nissan Altima
Tq for show information.this is a good skill🤙🤙
I tried this several times and got it. Thanks.
Thanks for your info...👍👍
Thanks heaps, procedure works like a charm.
Works for my nissan latio/tiida/versa 2006. Thank u.
It's not working on mine,y engine light doesn't blink on the last step
I clean my Accord 2002 throttle and disconnect the air sensor after I finish rpm when crazy up and down I did this procede and it worked thanks
Glad to hear the video worked for your accord, thanks for watching. 👍
Very professional......Thanks
Wow the best instruction video ever. Thanks.
If you look at 2.39 is it normal that the hand is pausing for 1 sec on its way back. I have the same on the my car and I thought it was a fault.
Exellent. I'm relieved as I thought it was a fault.
Thank you so much, this really helped.
Glad you got it done! 👍
Thanks a lot man this worked
Good video thank you.
Thanks you so much. I couldn't learn it using the Diagnostic scanner. Thanks to you I could learn the ETC.
Glad we could help!
Do you need to do this after replacing spark plugs in a nissan versa because I had to disconnect the throttle body in order to take off manifold to reach the spark plugs?
I cleaned my throttle body on my 06 Nissan Pathfinder. Started idling high around 1k, Check engine light after I put it back together. I did all 3 procedures about 20 times. Still high idle. Next day I tried the procedures with the engine stone cold, started it, came back a few minutes later and BAM 625 RPM! If this procedure isn't working for you with a fully warmed up engine and transmission, try it cold.
It was the idle high code on service engine soon (check engine) light. I have the factory service manual and the same steps for TB learning are in there also. i am curious if anyone else will have success with a fully cold engine.
Thanks a lot for this video it helps me a lot of time and money..
It worked! Thank you.
This is an awesome video and it’s the second time I’ve had to do it! I wrote down the steps in case anybody is interested:
1. Warm up engine
2. Turn car off
3. Place in Park
4. Release Gas Pedal
5. Turn ignition on for at least 2 seconds
6. Turn ignition off at least 10 seconds
7. Make sure accelerator released
8. Turn ignition on
9. Turn ignition off at least 10 seconds
10. Make sure accelerator released
11. Turn ignition on at least 3 seconds
12. Press and release Gas pedal 5x in 5 seconds.
13. Wait 7 seconds and PRESS and HOLD accelerator.
14. After 11 seconds engine light blinks
15. After 9 more seconds engine light changes to steady.
16. Release accelerator and start car within 3 seconds
17. Let idle 20 seconds
18. Slightly rev to see is normal.
Will this work on my x trail hybrid 2018 Thailand?
Thank you
Thanks mate for making this simple steps could do it easy performed it once nailed it. I cleaned the throttle body on my nissan tiida 2005 and had erratic idling. Almost had a heart attack lol. This saved my day. Cheers
Merci pour le vidéo
❤
Good video. What are the steps for a 2011 Mitsubishi lancer
Thanks!
thank you very much
Great vid
Is that for just the 2.5 liter Inline 4 or both 3.5 engines?
FYI..
I own a 2003 sentra spec-v, I tried many times and I was finally successful, but what I actually did was the following..
1*-ignition on for 3 sec.
- ignition off for 10 sec
2*-ignition on for 3 sec
-ignition off for 10 sec
3*-ignition on for 3 sec
-ignition off for 10 sec
^then ignition on and press on the gas 5 times in 5 seconds, release for 7 seconds then press on the
gas and hold till light starts flashing and follow like this video says
Thanks a lot it really help 👍🏽👍🏽
Glad we could help!
This appears to be the one that will do it. I took my Nissan Maxima 2007 (47,000 miles on it) into a Nissan dealer; because it was losing mileage per gallon. They said I needed the "Throttle Body" and the "Mass Air Flow" needs to be cleaned. They charged me upwards of $200.00.
When I drove the car out the "Engine Light" came on and stayed on. I took it back but then the Tachometer was going up and down badly in idle.
I do NOT believe the Nissan dealer "Re-Leaned" the computer as you do. Also I do NOT believe they cleaned the two items above correctly. I believe they just sprayed cleaner without removing them from the air canal; that goes from the air filter to the intake plenum.
I am going to remove them and clean them thoroughly. Then...
...I am going to do it just as you say. I believe it will solve my problem. Thank you so much.
Thanks worked on my Nissan Elgrand went from 1100 to 700
Thanks for the feedback Carl! We hope you connect with us on Cardone’s other social Channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
really helped allot.
Thank you it worked.
Thanks for the clear instructions. Seems that the idle is back to normal now but I still have one major problem. The "Check Engine Soon" light will still not go away. Any idea of how to remove it (as opposed to the usual battery terminal removal)? Hoping to find a way within the idle relearn steps on which I may be doing incorrectly...or not completing fully in order to have the light go back off. Thanks for any suggestions.
+Cardone Industries Wow thanks for the prompt response. I have a 2003 Nissan 350Z (3.5 DOHC). Yes..I know its old but hey it's still more reliable than all of my friends BMW's or Mercedes or Ford's :)
what happens if u don’t hear the sound ? done this like 5x and never heard anything
I have tried this o my 2003 2.5 sentra spec v. and sadly It did not work
I do something wrong though the process, or does it not work on this model?
please help, and thank you for the great video!
Tried it worked on my 2005 xterra
I have the same question as King J. My service engine light is on, just replaced the TBI and tried the re-learn procedure but it did not work. Do I need to clear the fault code first? It is 2006 Sentra
0:44 HAD me winning about filling the tank all the way!!!
I was like SHIIIT!! Ima have to fill up the damm TANK!!!
LOL so glad he skip that must lol
after re-learn would problem come back again?
Hi, can I use the same process for QX70 2014?
i have question
i changed my spark plugs on 08 G37 which required me to remove the throttle body. after i reconnect everything seem fine except whenever i turn ignition off or shut off the engine. It making the eletronic sound just like you did the throttle valves relearn. i tried all of those step but couldnt help. do you have any idea?
thank you
Will these procedures work on a 2011 sentra SE-R SpecV?
This worked! Thank you. I hope the light stays off.
Thanks for the positive feedback, we're glad we could help!! Be sure to connect with us on Cardone’s other social channels for related content:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
@@CardoneIndustries The light came.back on.😣
@@this.is.alkaline Give our Tech Support Team a call to help troubleshoot @ 888-280-8324 Mon-Friday 8am-5pm EST to speak with one of our ASE-Certified Technicians.
Thank you so much for your video ur a life saver!!!! 🙏🙏
This is crazy... it's like the esc for my electric Rc race cars throttle calibration! Lol
does this help out the low idle on a 2004 infinity g35 coupe?
Thank you man 👐🏽 this video saved me. I was on this problem for months (literally). I went from 1700~1800 rpm down to 700 on my Nissan murano
Thanks for the feedback Khalife, we are so glad we could help! Be sure to connect with us on Cardone’s other social Channels:
facebook.com/CardoneIndustries/
www.linkedin.com/company/cardone-industries/
twitter.com/cardoneparts
instagram.com/cardoneindustries/
Hello Khalife! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊
What year is your murano??