How To Install A Stair Nose On A Landing
Вставка
- Опубліковано 5 вер 2024
- How To Install A Stair Nose On A Landing
In this video, we start off on how to install a stair nose 1 particular way but in life things don't always go as planned. As opposed to using the U channel we used a glue down method on this stair nose. The video is for educational purposes and for entertainment we've included video of our epic failure using the U channel and how we recovered using the glue down method.
Please leave your questions in the comments and I will see you on the next one!
If you have a detailed question, please send 📷 pics of the problem and your question to
📧 YouFloor.net@gmail.com
☕️ Buy YouFloor A Coffee ☕️
www.buymeacoff...
Thanks to all the supporters and subscribers of this channel! 😁
If You Like This Channel, Check Out Our Other Channels - Links Below
📱iFloor . . . with him
/ @ifloor...withhim9721
📱Rent This Flip That
/ @rentthisflipthat
📱UnIdentified Channel
/ unidentifiedchannel
🌐 Facebook Page
/ youfloor.net
🌐 Facebook Group
/ 769392503713895
Tools You May Or May Not Need: (Affiliate Links Below)
CA Glue
www.amazon.com...
Tape Measure
www.amazon.com...
Dewalt Razor Knife
www.amazon.com...
Floor Mallet
www.amazon.com...
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I will receive a small commission (at no extra cost to you of course). This helps support the channel and allows me to continue to make videos like this. Thank you for your support!
I'm glad I subscribed to your channel to learn. Ya'll both have great accents BTW.
Hey Ken! Thanks for subscribing. Check out our other channel. It is full of diy projects not related to floors. Welcome to the diy family. Thanks for the comment
Ohhh I feel your pain brother! I was frustrated for you while I was watching man!
Thank you
The likely problem was with the track one of two things that it could have been. One the screws weren’t completely set which causes the track to not to deflect enough to pinch the mdf or the screws weren’t set low enough to allow the height of the mdf to fully seat in the track
I have thought about this situation a lot. I think if I would have shimmed the metal track up just a little, It would have grabbed. Because in the places where it did grab it caused a slight cup it the stairnose. Telling me it was too tight. If I had to do it again, would probably slip a strip of cardboard under the u channel to bring it up enough to grab not not cause a gap in the front. This was a very frustrating install, as I have do e this numerous times in the past. Thanks for your input. I appreciate the advise. And thanks for the comment
@@YOUFLOOR yea shimming it may have helped but then you run the risk of the moulding sitting above the floor. Those things are a horrible design over time if they are installed in a high traffic area the mdf wears on the track and the transition starts getting loose eventually it comes out of the track.
Going through this pain right now. This metal track just seems like a horrible idea.
Help. How do you transition from wood to carpet on the last stair at the top landing? There is no bull nose on the landing it is flush. Don’t want to start pulling up the carpet on the stairs until I know how to finish the project.
Cut the carpet back slightly, lay a thin piece of flooring and use a room transition
Good Job
Thank you
with the pergo outlast+ it seems that there are no options for a flush stair/edge bullnose. the pergo brand stair edge overlaps the top of the flooring similar to what you used. Is that the only things you've had experience with?
I've had a couple like that but don't remember the brand. One time I took a stair tread and a vinyl plank. I clipped
The plank to the tread at the front. Then took a heat gun and shaped it over the round nose. I used a 2x4 wrapped in cloth to not scratch it. Then ran it back and forth as I blew a heat gun on it. It took the shape of the stair tread underneath. And I had a custom plank with nose built in. Then I just cut the back piece to fit. With I recorded it. I thought I made a video for it but I guess I didn't. Hope that gives you something to think about. Thanks for the question
I have one to fit it next week 195m between room and kitchen thank you
Yes sir good luck with your project. Thanks for the comment
Your video will help. Thank you so much for all your efforts
If the landing floor is ceramic and comes flushed to the raiser, how would you go about to install a stair nose? The current one is made of black rubber, is coming undone with the years (was glued in place) and resist re glueing
I would love to take a shot at coming up with a solution. Could you send me a couple pics from different angles so I can get a better idea of what we are dealing with. Youfloor.net@gmail.com thanks ,Z
Hi - I am applying 3/4" hardwood to a stairway landing, which is 6.5 ' x 3'. In this case, I am told I have to place the stair nosing first, working back to the wall (to make sure the nosing is exactly where it needs to be , snug on the edge of the stair). The back of the nosing has a groove, not a tongue. So how do I nail in the next course when there is no tongue to nail into?
Go to 9:52 in this video. It may help or give you an idea. You can install you nose and the first row. Then turn your floor around using a spline. It’s like the first board has 2 tonges Hope that helps. ua-cam.com/video/At936Q9YL_o/v-deo.htmlsi=WWbFQFlCjHx4etsM
Ok, question, I have removed the nasty carpet from my stairs and the 1st small landing. This landing has the newel post sitting on the subflooring. How do I apply bullnosing to this area? Should I remove the newel post and set on onto the new floor?
Whoa that a tricky one. Hard to say without really seeing it. If you don't mind could you snap a couple pics from different angles and send them to me. Youfloor.net@gmail.com I'll take a look and see what I what I would do. Great question. Thanks
@@YOUFLOOR yes stand by
@@YOUFLOOR Next question, I wanted to install bottom and top of stair-landings with Luxury Vinyl - hardwood is costly, I am not sure what direction the planks should.
The direction will not matter structurally. That's more of a preference. But I would probably run it in the direction that the majority of stairs are running. I am looking at your email asap
What color is that flooring? I love it!
I think it's called pewter