I Bought and Fixed this Broken Motorcycle
Вставка
- Опубліковано 2 жов 2024
- This 2012 Honda NC700x has another chance at life! After spending many hours troubleshooting the issue, I discovered the bike had a defective/damaged cam chain tensioner.
Thanks for the 100 subscribers!
Don't ride without a helmet,even if its only around the block...my uncle died that way, he went to the store 50m away and soke idiot hit him...
Great vid. Great sleuthing. So sad for the previous owner that after running "Diagnostics" the Dealer's shop failed to notice the cam timing marks were out. One would think that timing issues would show up on a diagnostic readout or that someone would've pulled the valve cover and checked the clearances etc.
Worked out well for you though. Nice work.
Well sorted out - good job.
Great video, certainly a standout in a sea of typical crappy UA-cam videos. The only thing I wonder is why you made a gasket when Honda builds these engines with a thin bead of sealant there, not a gasket. I have done a clutch replacement on an NC700X and followed the service manual instruction for using the appropriate sealant. It worked just fine; no need to make a physical gasket.
I am reading of a number of NC engines that had a cam chain tensioner fail in the first 20,000 miles. Seems once you've past that mileage point, you're OK.
Well done,young fella!
Top film, I need to see more of your stuff!
Thank you, that's very kind!
@@rookiewrenching938
Nice video, very helpful.
Do you still own the red Honda ?
I mean, how is it even possible to mess this engine up? It should run 250k km no problem.
Good video!
The background of the used bike just like this guy said it was perfect and long story short he dropped it at high speeds and covered it up. I wish I payed more attention but I was too excited since it was my first bike
Great investigation. Congratulations.
Love the graphics! I can tell you spent a lot of time editing. But the start to finish process was super satisfying
⭐⭐⭐⭐⭐
Great job ,How did you get the cam chain sprocket off,with engine still in frame?
This a great video. Good job. I have the same bike and I love it. Love the way the torque comes on. They're known to be super reliable and I haven't heard of this happening before. Simple enough to repair though and I know now to watch for this.
Can't understand your username "Rookie Wrenching" If this is rookie Wrenching, wondering how a does it ... Great job and movie !
Amazing skill . how many times did you take on this project?
How do I remove a computer box on this Bike
Have heard of them
failing, thanks for sharing.
Good job. I think you can get the tensioner out by just undoing the top two bolts.
Hi BRILLIANT hope this bike is still running they say they can do 1.0000 miles
1 mile?
Wow you are an expert bike's mechanic, I would like know your mechanic knowledge.
I'm flattered, thanks! In reality I just try a bunch of stuff until it works 😅
I should've been a mech. Came up with the same hypothesis as you on each step, at least up to the timing.
I would have just got a new tensioner, they aren't that expensive, at least compared to an engine.
So smart 👌🏻
very good work.
Thanks for the video, nice to see the insides of these motors.. not much info on them as they are very reliable usually, I just picked up one with extremely low kms. Low rev limit is hard to get use to.
Congrats on the new bike! The rev limiter was hard for me at first too. I kept hitting it in first and second gear whenever I was distracted 🤦
@@rookiewrenching938 where do you find these broken bikes?
@@turkishman4202 Just local classifieds. At the time, I was scanning bike listings multiple times a day to find deals.
Me too, I think hitting the limiter causes the camchain to bounce and destroys the tensioner - as it's only manual shifts that this happens to ?!!@@rookiewrenching938
Mine has gone on a 2021 at 6500miles. Really not impressed with Honda build quality, or lack of!
Not sure.
I have a NC700 with 140.000 km, 2013 model and I have no issues. First clutch, first cam chain tensioner.
But I had to change the wheel bearings front and back already twice. That being said , the bearings aren't manufactured by Honda.
I am actually very pleased with the Honda quality, at least on this bike.
And yes, I've heard about cam tensioner issues from other owners as well.
Safe rides 👍