2024 Ford Super Duty Factory 5th wheel tow prep install....F-250 and F-350...YOU CAN DO IT!
Вставка
- Опубліковано 30 бер 2024
- Installing the Ford OEM Puck system on the new 2024 Ford Super Duty F-250, Ford Super Duty F-350, Lariat, Tremor, or XLT or XL. this procedure you can do yourself. I’ll show you how to install the New Ford Puck System on your 2023 and 2024 Ford Super Duty truck.
I’ll also give you links below to all of the tools needed. Also links to the instruction Sheets so you can put it all together.
Easily watch my install, and then subscribe to see many more accessory installs and must haves on the new Ford Super Duty Tremor truck
#Ford #Super Duty #how to install #affiliate #afflink
Spring loaded Metal Center Punch:
amzn.to/49isNGE
Hole saw 4.25 inch:
amzn.to/3THnjzl
Hole saw 3 inch:
amzn.to/3IXVE8H
Hole saw ¾ to 2.5 inch hole saw kit:
amzn.to/3TZdlek
Torx 24 plus set:
amzn.to/43HGGgh
Wet Dry Vac:
amzn.to/3vqDBF0
Trim Removal Tool:
amzn.to/3U17jtH
Rechargeable Impact Wrench:
amzn.to/4cAYWw1
Dewalt complete tool set with 22 mm sockets:
amzn.to/49h3PaH
Instruction sheets:
2023 CMY Super Duty 5th Wheel gooseneck hitch Prep package:
www.fordservicecontent.com/Fo...
2017 to 2023 Super Duty 5th Wheel 7 pin installation sheets:
www.fordservicecontent.com/Fo...
I also have links below to 2017 to 2022 Ford super Duty step by step process to install the factory 5th wheel Tow prep package.
6 part series:
Part 1 of 2022 Super Duty F-250 7.3 Godzilla install:
• 2022 Ford Super Duty F...
I know it takes twice as long to film it all so thanks for taking the time.
You did a great job on this video! I'm not installing a hitch but wanted to see the procedure. Thanks!
Thanks, I appreciate the feedback and happy to have you check out the video.
Very detailed and easy to follow. Can’t wait to see the towing videos that follow. Thank you!
Great video ,very well done. The factory hitch is usually the best option,I’d done it the same way you did hanging the bed off your trusses👍
Excellent instructional video, and indeed one wants to order the truck or find one that has the puck system in it from the factory if possible and as you pointed out its not possible to even install the GM unit after the fact. I was going to mention a trick with drill bits if there is a danger of flying through a hole and unintentionally damaging something. I know its easy to have a drill grab and "thread" itself into thin material and things can go wrong fast. The trick is to have some rubber hose of an inner diameter that is slightly larger that the drill diameter in question, a smaller drill sizes can use vacuum hose or a size of fuel hose for example. Chuck the twist drill and then cut the hose ... could be as little as a 1/4 shorter or a 1/2 inch as examples. Then there is no way the drill bit can accidentally go deeper than the "give" of the rubber hose. A hole saw can be done similar by using a narrow section of rubber hose and it can be slit and then cut to length so it goes around the hole saw and then a hose clamp is utilized to clamp the hose to the hole saw. Yes its a lot of messing around but if something is very critical it might be worth the effort.
Great video.
Great job 👍
I'll eventually get this done on my truck, so as Arnold says...
"I'll be back"
Thanks I appreciate you watching.
Great video very detailed 👍👍 one question do you have size of all the bolts used??
You have to have that tailgate up at 80° or you’ll have a bitch of a time getting that out of the driver side tensioner groove that’s the key to getting that tailgate off with no trouble 80° up and then it’ll come right out of the notch. Also you should mention in your link that that the side measurement of 10 1/4 is from the wheel well not the side of the bed. Great video.
easier to get from factory isnt it?, smart to do it b4 bedliner......aftermarket is usually better anyway.......
Absolutely, get it from the factory if you can if you order as it's only a 500 plus option, but most dealers aren't getting this put in on their stock orders. Not sure why. I do prefer this sytem from all the big three over a BW turn over ball or other puck systems not being OEM. Ford and RAM you can ad later, Chevy, you cannot get their puck system added after the truck is built and one would have to do a turn over ball system. Thanks for watching.
Looks like 36 and 1/4 on the center.
Traitor flag killed it for me. I'm out.