Add two simple fuel shut off valves on fuel line one before and one after fuel filter. Small piece of foil under filter to channel oil flow down into catch pan, then pop a hole with a nail on bottom edge of filter followed by one on top edge to let filter drain before removing.. no to little oil mess.
Just got one of these with 242 hours on it off my elderly neighbor. It sat for at least two years and she said I could just have it but I gave her $100 for it
If your oil is ink black, you waited too long to change it. Also change the oil filter every oil change. Those engines are expensive, and motor oil is cheap. Don't forget the air filter. Not enough air will carbon up your engine. If you can find ethanol free gasoline, use it. Ethanol pulls water out of the air, and will make a gooey blob in your carburetor bowl and corrode it. I don't even use it in my old 2000 Ford Expedition. Don't forget to grease the front wheels and the spindles. Find the 4 grease fittings & pump some grease into them. Feel all the steel idler wheels on the mowing deck, & plastic ones under the mower frame. If any feel rough as you turn them by hand, spray a LITTLE bit of WD-40 on the center of the pulleys. Then spin them around so the WD works its way inside the ball bearings. Do NOT get WD -40, or oil, on the belts, or in the V of the pulleys where the belts touch. If you have a plastic transmission be sure to blow, or vacuum, the grass clippings off the top of them. Grass packed in there causes 99% of the problems with the plastic transmissions. When the axle seals start to leak, use silicon sealant, or some caulking to seal the new seals into the transmission, since they have a tendency to work their way out of the transmission and leak grease out. Don't worry about the oil from the grease inside the transmission, that leaked out. It is full of grease from the factory. There is plenty of grease inside it. You can ignore a slight oil leak from around the axles.
I'm not sure, those filters are tiny so it wouldn't be that much. When you get down to adding your last quart of oil just add a 1/4 at a time until you get to the desired level on your dipstick. Thanks for watching and commenting.😁
Check in the description area below the video, there are two links, one for the front tires and one for the back tires. Just click on it and it will take you right to it. Thanks for watching!
I own this machine for 5 years, bought it from Lowes. Year 4th engine oil leak, year 5th hydraulic shot. I better getting new machine intead of fix it. Piece of junk machine. I would not recommend Husqvarna. I do own a Husqvarna blower and that working ok.
Had my husqvarna 46 for 8 years now. Never changed the oil, never added oil, no new oil filter, or air filter. Put gas in it and cut grass. Hah still running like a champ!
Thanks for the coaching, very helpful! I put the kit and my fuel filter was broken!
You help me make a list of things - I will need to start. Thanks for sharing.
You are so welcome!
I always fold up a piece of cardboard and slide it under filters like that to catch spillage
Love those tires!
Add two simple fuel shut off valves on fuel line one before and one after fuel filter. Small piece of foil under filter to channel oil flow down into catch pan, then pop a hole with a nail on bottom edge of filter followed by one on top edge to let filter drain before removing.. no to little oil mess.
Good advice.
Just got one of these with 242 hours on it off my elderly neighbor. It sat for at least two years and she said I could just have it but I gave her $100 for it
Good deal. Good tractor.
Very nice video. Simple to follow. I'm buying one tomorrow with 50 miles of usage and this will help me do the mant as soon as i get it home.
Glad it helped you out! Thanks for watching.
Wat oil did u use. Does it matter which one u use?
Do you know what the inner diameter of the oil drain hose is? I need to buy one as I Dont have the original. Thanks.
1/2"
turn the drain plug an eigth of a turn counterclockwise, then it unlocks, then pull it forward to get the oil flowign out.
Yes, that is correct.
Muy bien explicado
Thanks
You're welcome.
Any maintenance required on the transaxle?
Did you put oil inside of the new oil filter? I know that you greased the ring top
What size hose do you use 5/8?
Yes!
If your oil is ink black, you waited too long to change it. Also change the oil filter every oil change. Those engines are expensive, and motor oil is cheap. Don't forget the air filter. Not enough air will carbon up your engine. If you can find ethanol free gasoline, use it. Ethanol pulls water out of the air, and will make a gooey blob in your carburetor bowl and corrode it. I don't even use it in my old 2000 Ford Expedition.
Don't forget to grease the front wheels and the spindles. Find the 4 grease fittings & pump some grease into them.
Feel all the steel idler wheels on the mowing deck, & plastic ones under the mower frame. If any feel rough as you turn them by hand, spray a LITTLE bit of WD-40 on the center of the pulleys. Then spin them around so the WD works its way inside the ball bearings. Do NOT get WD -40, or oil, on the belts, or in the V of the pulleys where the belts touch.
If you have a plastic transmission be sure to blow, or vacuum, the grass clippings off the top of them. Grass packed in there causes 99% of the problems with the plastic transmissions.
When the axle seals start to leak, use silicon sealant, or some caulking to seal the new seals into the transmission, since they have a tendency to work their way out of the transmission and leak grease out. Don't worry about the oil from the grease inside the transmission, that leaked out. It is full of grease from the factory. There is plenty of grease inside it. You can ignore a slight oil leak from around the axles.
Thanks for commenting!
Cómo ajustar la banda de cortar secped
Can you put wheel weights on these?
Why?
@@CycleFabhills
My belts are lose what i do they are right size still lose please help
What size is the oil filter
How many quarts. If filter not change
I'm not sure, those filters are tiny so it wouldn't be that much. When you get down to adding your last quart of oil just add a 1/4 at a time until you get to the desired level on your dipstick. Thanks for watching and commenting.😁
Can you share the Amazon link for the oil? And is it the same as SAE 30?
Thats what i use in mine
Husqvarna recommends SAE 30 oil in my unit.
For the hotter months yes.
Which one 5w 10w 30 or 40
The kit u showed on the video did not come up
@@BertaCarkerthey make a 30w
@@BertaCarker5w30 honey
nice tires, where to buy?
Check in the description area below the video, there are two links, one for the front tires and one for the back tires. Just click on it and it will take you right to it. Thanks for watching!
Here is a video I did on those tires. ua-cam.com/video/92JDS0As19U/v-deo.html
Just click on it.
use red grease on fittings and there’s a clip removal tool. our DPW will take used oil and filters .
Iv been selling ALOT of ethonol free premix at work. People are like yeahhh but isnt pump gas good. I say it works yes but its not exactully good
I run ethanol free gas in my small engines too.
What is the oil weight 10w-30???
I own this machine for 5 years, bought it from Lowes. Year 4th engine oil leak, year 5th hydraulic shot. I better getting new machine intead of fix it. Piece of junk machine. I would not recommend Husqvarna. I do own a Husqvarna blower and that working ok.
I heard that some later ones have had issues, what motor do you have in yours?
Had my husqvarna 46 for 8 years now. Never changed the oil, never added oil, no new oil filter, or air filter. Put gas in it and cut grass. Hah still running like a champ!
@@xourheartsdesirejesus dude lol how big is the yard
Very informative. I’m going to attempt this tomorrow without my husband!
THANK YOU! I have been putting off maintenance as I have never needed to do this before. I appreciate the details you gave.