this solution is not problem as long as you do your service at time and every oil change guys clear the filter... i am using croslland almost 200.000km, 3x chanfe time belt and no problem..
This is a recall from PSA (when it was still PSA) because the batch of belts fitted to this particular engine are known to snap. There is an improved belt material which is fitted instead to resolve the issue! That is why many other puretech engines have no issues at all because they arent part of recall!
How long would you say it takes to just replace the rocker cover gasket and if I'm going through all that trouble for an oil leak shall I go the full way and have the cambelt changed at the same time if it doesn't look to bad....
Without videoing it I’d probably take an hour just to do the gasket… wouldn’t be a bad idea to change the Cambelt they are horrifically unreliable on these engines
It is possible to do the job without the use of timing tools but I do not recommend trying this approach because a mistake could cost you an engine - I suggest you buy the tool… it is cheaper than a new engine 🫣
I'm about to buy a used Peugeot 208 e-thp 1.2 , 110 hp. 2019, 95000 km. But im really sceptical after all those negative comments that ive recently read about this engine. My mechanic is going to check everything, plus check the full history service book. Should i avoid it, even if everything look good?
Yea definitely avoid them they are genuinely terrible engines. The one in the video had full dealer service history and three cambelts in four years!!!!
Awesome video, really really appreciate it, could I possibly run something by you? I have a Vauxhall Crossland same engine and its throwing up the low oil pressure fault, and the car is going into limp mode! So what ive done so far is remove the sump to see for blockages in the pickup and to be fair it wasnt terrible, there were some micro fibers which ive removed, i also changed the filter and oil but the fault is still there? The belt does have micro cracks all over it and i will replace it using your videos as a guide, but i fear just changing the belt will not rectify the fault? Is there something else I'm missing? When i plug it in its coming up with oil pressure solenoid valve circuit low? Any help from you would so appreciate.........
Thank you so much for the reply! Really appreciate it. The pick up is slightly different on mine, My one doesn't have the black pipe/funnel thing! My one looks like this ua-cam.com/users/shorts3FU03Dxo7YM?si=kmrB6MOwcr1kxKVb
The later Cambelt pulleys have a raised edge on the outer part of the pulley. So you don't have the clearance for the belt to fit through. I had to remove the inlet pulley as to get the old belt off and new one on.
I guess they will stretch but since you have to replace them so often, you don't notice it as much. Chains are superior, don't want anything else @@maxautouk
Great video, thanks for taking the time to clearly explain the job along with all the tips👍
Glad it was helpful!
The level of laziness using an air ratchet to take the battery terminal off. I adore you
If a power tool fits. It gets used. 😂
Time is money.
Dam right
En you have been doing this job for many years your hands kill anything to make it easy
Very good video. All video's should be made like this. Good job👍🏼 and thank you!
That’s very kind thank you!
Im just knew that peugeot engine timing belt should be wet and not dry after watched this video. thanks sir
Glad it helped
Good job 👍🏼
this solution is not problem as long as you do your service at time and every oil change guys clear the filter... i am using croslland almost 200.000km, 3x chanfe time belt and no problem..
This is a recall from PSA (when it was still PSA) because the batch of belts fitted to this particular engine are known to snap. There is an improved belt material which is fitted instead to resolve the issue! That is why many other puretech engines have no issues at all because they arent part of recall!
At what mileage was this car the sump is not so dirty
@@filipkrstevski5449 40k
How long would you say it takes to just replace the rocker cover gasket and if I'm going through all that trouble for an oil leak shall I go the full way and have the cambelt changed at the same time if it doesn't look to bad....
Without videoing it I’d probably take an hour just to do the gasket… wouldn’t be a bad idea to change the Cambelt they are horrifically unreliable on these engines
Hi great video can you please tell me where the PCV VALVE is thanks
I must admit I’m not a hundred percent where it is located sorry - this is a customer at and I don’t have access to it soo can’t check
Great video How many kilometers should the timing belt be changed?
If its the original belt then immediately they are known to cause issues
Did they fix it tho? Can I buy it from official dealer?
Yes you can buy it from main dealer
Sometimes the bits of timing belt also damage the vvt, oil pump and block the pick up tube
I've got a bearing noise sounds just like the alternator bearing have gone but its notvthatvor the welt belt pulls any ideas im thinking oil pump?
Im afraid without hearing it for myself in person i have no idea what to suggest sorry!
Will also need to clean the wire screen, at the end of the engine oil pick up tube, in order to complete this job?.
Only if the belt has started to break up 👍🏽
Is number one piston at tdc i dont have tool for timng
It is possible to do the job without the use of timing tools but I do not recommend trying this approach because a mistake could cost you an engine - I suggest you buy the tool… it is cheaper than a new engine 🫣
What part of the country are you in? Need belt doing on my sons car.
Brookeborough, County Fermanagh where are you?
thanks
No worries!
I'm about to buy a used Peugeot 208 e-thp 1.2 , 110 hp. 2019, 95000 km. But im really sceptical after all those negative comments that ive recently read about this engine. My mechanic is going to check everything, plus check the full history service book. Should i avoid it, even if everything look good?
Yea definitely avoid them they are genuinely terrible engines. The one in the video had full dealer service history and three cambelts in four years!!!!
@@maxautouk thanks a lot. Really valuable information. Is there any version of 208 engine reliable that i should look for ?
The 1.6 HDi is ok
@@maxautouk hard to find, maybe i ll check for a Clio, like an 0.9 tce engine. I hope that is more reliable.
Hi there how much is the labour for this job ?
I could say it depends very much on where you live but in my area easily £400 on labour, maybe more
Bu araç kaç model, kayış kaç km’de değişti?
This the 1.2L petrol puretech engine and this timing belt had only done 15,000km
Awesome video, really really appreciate it, could I possibly run something by you? I have a Vauxhall Crossland same engine and its throwing up the low oil pressure fault, and the car is going into limp mode! So what ive done so far is remove the sump to see for blockages in the pickup and to be fair it wasnt terrible, there were some micro fibers which ive removed, i also changed the filter and oil but the fault is still there? The belt does have micro cracks all over it and i will replace it using your videos as a guide, but i fear just changing the belt will not rectify the fault? Is there something else I'm missing? When i plug it in its coming up with oil pressure solenoid valve circuit low? Any help from you would so appreciate.........
Did you remove the pick up tube completely?
Thank you so much for the reply! Really appreciate it. The pick up is slightly different on mine, My one doesn't have the black pipe/funnel thing! My one looks like this ua-cam.com/users/shorts3FU03Dxo7YM?si=kmrB6MOwcr1kxKVb
Is the seal on the pick up tube damaged ? Because that can create oil pressure problems too
Can i ask where you're located? Is it a job you could do? Could I possibly take a number? Regards
@@JohnDoe-rf4td I am located in Northern Ireland in a town called Brookeborough - where are you?
The later Cambelt pulleys have a raised edge on the outer part of the pulley. So you don't have the clearance for the belt to fit through. I had to remove the inlet pulley as to get the old belt off and new one on.
Thanks for the comment information is everything! What year is yours?
@@maxautouk 2018 peugeot 2008.
@@maxautouk i work at vospers so work on peugeot and ford
Sweet, extra information is always mega helpful
GREAT VIDEO /IT WOULD BE EASIER IF YOU TOOK THE FIRE PANNEL OUT/ TWO WIPERS SOME PLASTICS AND FEW SCRUES
I think underneath the cowling is just a scuttle tray that is welded to the body so you wouldn’t actually gain any more space
Stupid wet belt. Real pain in the wotsit.
Yeah not a great design is it
Actually mindblowing to me that timing belts are still a thing. So stupid
Unlike a chain they don’t stretch and slowly make the engine run worse but this timing belt set up in particular is an absolute joke 🫣
I guess they will stretch but since you have to replace them so often, you don't notice it as much. Chains are superior, don't want anything else @@maxautouk
@luresforall and can save you some time and money!
What a misery.....
Not a great engine
DO NOT BUY 3 CILINDER ENGINE CARS !!! These are JUNK !
They do seem more prone to go boom!
French car technology.......:-/
Not great in this instance…