How To On: Everything About A Stock Motorized Bicycle Clutch! (Full Removal -To- Pad Upgrade!)
Вставка
- Опубліковано 22 жов 2021
- Before you buy a super clutch! Check out the Semi metallic Pad Video: • Video these grip like a mofo! I have been using stock clutch with these pads on Minarelli with zero issue of slipping even when pipe hits!
So this just fast video on how to remove the clutch! Why they slip! The fact most overlook the back side clutch plate! How it works! How to tighten a flower nut perfectly every time with out guessing! How to grease your drive train gears!
Just fast video since I got crap in my clutch area. figured I show to to remove one and what is involved in the ordeal! I also show you guys an old trick to really help the plates grab 100% better on your rubber pads! Most overlook the back plate lose tons of gripping force!
Hope this helps a few with questions of how this unit is removed! It seems to stump many all the time in forums and on face book! - Авто та транспорт
My ball Bearing is stuck in the clutch cylinder, how Do I get it out so I can make my clutch work again? seems to be wedged between something inside, I can't adjust the flower nut to make the clutch work anymore and the bike won't run.
Are the semi Metallic pads the green ones?
Just got my first 50 cc. As for starting from a complete stop. Im winding it up really high, its slow taking off. I changed the clutch pads but the new ones already have that burned look. Do I adjust the carb? Change the method of moving from a stop?
How small is your rear sprocket. 50cc has a hard time with smaller sprockets. 44-46t is what most use on 50cc. 36-38t with 80cc kits . Most start out clutch in and peddle some get going on 50cc engines
@@BuildBreakFix I was going to count the teeth never got around to it. It always starts in 4 or 5 pedals, maybe Ill just go with that. I guess if you pedal start you dont get the black clutch pads?
How do u get clutch gear from the back of pressure plate
considering it's a 20$ entire kit item or a 10$ pressure plate alone item lol. for 6 hours of work to get pull apart bearing off with a reverse gear puller would be crazy
Is it normal that the clutch moves up and down or left or to the right? My engine rattles loud
Yes it's normal on these kits
YOU MAY NOT NEED NEW PADS!!!! I've watch several of these videos of changing the clutch pads. In all the videos the pads seem stuck in the clutch pad gear. It seems to me if they're stuck in the gear, the spring loaded outer sheet metal disc is not going to be able to push the pads against the inner flywheel disc. This being the case, the only friction you're going to get is against the outter sheet metal disc and it's no wonder the clutch is slipping. I have not tried this but most likely you could remove the clutch pads, sand the edges so they fit in their recessed slots easily, button it up and it would run fine. There's a good chance they're not wore out but just stuck in the gear and can no longer be pushed against the inside flywheel. ; )
I find you just sand then on concrete drool bit
How tight do you tighten the 14mm by 1 nut? Thanks
14 ftlbs.
What length throttle cable can I use mine too short and I’m on budget my bike a bit bigger
Not sure what you are asking. Length of cable? I'm pretty sure all "motorized bicycle throttle cables" are around 48inchs or 1meter roughly. Only like 8$ on amazon
@@BuildBreakFix I need one that’s longer
I need help , my small sprocket teeth *the right one next to the big one * turned to dust , its completly gone. where can i buy one , i have been looking everywhere and i couldnt ride my bike in 6 months, please is there any website wich ships it , maybe to germany aswell ? please tell me .
Here my man! Amazon link for what you need! Front Sprocket Cog 10T Teeth Iron Alloy for 48cc 80cc 2 Stroke Motorized Bicycle 415 Chain Front Sprocket Gear Replacement Motorized Bike Accessory a.co/d/hexXHOO
@@BuildBreakFix Thank you , but not that one the one from the other side , i think its called snall bevel gesr
@@paulthedude oh you mean on clutch side? Here then. It's called a bevel gear. a.co/d/3f75199
I just lost my bearing can someone help me figure where could of it gone
Do you mean the ball that goes in the bucking bar part between the pins? This may be what you are asking about! 10$ for new set www.ebay.com/itm/233628054250?itmmeta=01HTZY8065D72J263ACY08M15X&hash=item36655132ea:g:RCoAAOSw9vpc5dgf&itmprp=enc%3AAQAJAAAA0FKuA3gUJ80D%2BW1dbF%2FMCnSEyT4GUPeoqovlB5j9EYBCz2lBcgtfGy%2BnBhglOyuyRDCsPMGs1rJIA7p9bSBO9u8SAYg6OBcl465hURTJ0Zm0IOz0Fbp6n5fs1w0%2FNvdKJ%2FVAPWV4K8ueoeqXqkczjpMOsXMErkGpMiNRip40pK0ZWohhkSZ9ATtnzx2sRt6zdGI4Xaeolv3mjF56s8spMaNk3bnCvj8D%2F2Spz45h8H0rnw6bJZo1sRR%2BtEPV74Tp8TOhjLtX3P52%2FhXZDJmT0rc%3D%7Ctkp%3ABk9SR5iDoP7XYw
I changed mine and now my bike moves with no clutch how do I fix it
Flower nut tighten it fully with lever pulled in fully. Back it off 1.5 turns while lever is pulled in. You should see clutch release at this point. When lever is let out. Should grab again. Release when pulled in.
@@BuildBreakFix I also changed the magnet coil could that affect it
@@BuildBreakFix I wish I had a visual demonstration
Sorry I meant 18 mm
Yeah I know what yeah meant lol. Biggest nuts