Many thanks for this video! My Samsung C480 had very dirty prints. On inspection the drum was also very dirty. First cleaned the transport belt, but that did not help. It turned out that the toner waste reservoir in the drum unit was completely filled to the rim. So it couldn't clean the drum anymore. I removed the roller and shook out all toner waste. Cleaned the drum unit and voila: happy clean prints!
Thank you very much for this video. I was able to fix "image ghosting" on a Samsung CLP-315W by following your instructions to clean the charge roller with water. Imaging Unit was only at 1100pgs, 84% life remaining, but living in dry climate(Denver, CO) made the charge roller(and foam roller) ineffective at removing excess image toner. Imaging unit drum was diagnosed as culprit by measuring 7.5 vertical inches between original image and ghosted image. Again, 10,000 thanks.
Original factory units that come with the printer do not have the thermal fuse anyways. In order to reset the drum without the thermal fuse, just put a jumper across the terminals of the resistor (small piece of copper wire will do). Close the door and plug the printer in. It will say "Initialize..." followed by a flash of lights, after which it will most probably reset itself as it is unable to "blow" the fuse (the cycle will repeat itself indefinitely). At this point switch it off (unplug power) and take out the holder with the resistor again. Take the jumper off (break the wire) and put the holder back in. Close the door and let the printer startup. Tested on CLX-3300 series with CLT-R406 drum.
Hey, You are genius ! «How to remove and clean Samsung Transfer Belt CLP-365» + «How to Clean an OPC Drum for Laser printer/Copier» + «CLP310 320 360 CLX Drum unit Rebuilding Instructions» helped me to diagnostic my CLX-3175N ghosted pic (from top printing) on on the bottom of each page, and was spaced to 188mm. I read forums, but was not sure if it was the transfert belt or the OPC Drum. Those both parts are quite expensive : ~ 120€ for both, not sure it worth it ! I did the cleaning like you said on both items, on the tranfert belt, it didn't change. But I for the OPC drum, I well listen your precious comments and found after the 1st rebuild a better printing, but still some few ghost pic on bottom. I pushed a bit all the wiper blade for enable it better fit the OPC Drum. And it worked... !! I know that It won't be lasting, but I know now for sure that's it's the OPC Drum, the wiper blade exactly. [EDIT] : I forgot also to mention excellent tuto «Toner Cartridge Printing Defects: Causes and Solutions». Many thanks !
a ghosted print may be related to the drum or to the fuser unit. the distance of 188 mm is related to the drum but I don't think it's a wiper blade problem. Probably you have to change the OPC drum
Hehe... Just have a look when I gently pushed the wiper blade in the drum direction in a way of having a better contact on the drum you can see spectacular result on the right : imgur.com/ssh7i6P or i.imgur.com/ssh7i6P.jpg Deprives me of a doubt : I also changed the black toner cartridge. I don't remember when in all those repair process (quantity
the space of 188 mm is related to the drum the developer roller is 26 mm but the ghost images are related to toner cartridge too. the developer roller is the roller covered with toner you can see on the toner cartridge
Hi viandent sorry couldnt find my original post but u asked me to respond if I had any luck, well i did! I was getting repeated black lines a long my pages dispite changing fuser unit and cleaning drum unit. Well I completely swapped te drum unit out, no more black lines! Clp365w. Yay! So I'm assuming drum unit must have been "damaged" in some way as image counter was only at 1982 not sure but working perfectly now. Thanks for yr help and keep the informative vids coming :)
Thank you for the video. I have a Samsung C460W that began to have faded printing. Cleaned out the waste toner tank, the transfer belt, and finally the image drum per your videos. Wow, a LOT waste toner in all those components! I found it best to do this job outside on a nice day. Used an electric leaf blower on low to blow everything out. Not sure why cleaning the image drum assembly helped, but it did! I am thinking it is the cleaning of the charge roller and the light rod that actually makes the difference. All of the other cleaning is just to get rid of the excess waste toner, which must be disposed of before the containers become full.
worth noting, for anyone who doesn't know, when replacing or refilling/resetting/cleaning the drum and/or toners, you should grab a ziploc bag and also empty the collection cassette into it, making sure to wear a face mask and gloves for protection against the toner dust. make sure to completely close the ziploc bag afterwards and dispose of appropriately. Most of all, don't be put off by the fact the toner in the bag will resemble mold lol.
@@EvanCarrollTheGreat Patently false. Most modern toners are composed of 85-95% plastic. The other 5-15% is comprised of ground silica, iron, chromium and zinc. What you're thinking about, is inkjet cartridges. Not even close to being the same thing. Regardless, you don't even want to have inkjet liquids touching your skin because they also contain petroleum. Petroleum is a skin irritant.
I was going to trash my CLP315 because it wouldn't be economical to fix it. This was very helpful and the thing is printing perfectly now. Thank You. The one thing I can't figure out is how in the world the reset fuse replacement can be figured out by the printer that it just hasn't been lifted and resoldered. That is a new one for me.
+viandant5 No problem. I was just remarking that the videos that I have seen are strange because having to replace one thermal fuse or resistor with another and the printer somehow knows that it is another one of the same value is a strange concept for a guy who was a radio technician for a lot of years. Thanks again.
@@Dickwooten When the printer sees a drum unit with very little resistance, it assumes a new one has been installed. It then blows the fuse by passing a lot of current through it. when this fuse blows, the 100k resistor is the only current path left. The printer now knows it has successfully "started the lifecycle" of that toner. It has no way of recognizing the toner (or a new one) besides a low resistance path that became high resistance after trying to initialise it.
CLX DRUM SHAFT INSERTION: Samsung seem to use the same drum design for many of their printers esp CLX series but bearing different Model numbers. The most important point in dismantling and removing the drum shaft is a result of the internal electrical contacts that while rubbing on the shaft, allow a clean shaft to pass easily through them in only one direction. This is from the end bearing the gear (and internal contacts) towards the opposite end. Unfortunately this is not mentioned in this "Remanufacture" procedure but can be seen by carefully comparing both the disassembly and assembly segments of the video.
I found that my imaging unit had an overflowing toner that stacks up from the top. Following your guide, I cleared out the waste toner tank (there was a TON of powder). Let's see what happens.
Excellent video. I followed the instructions and did pretty much what you did on the video on my CLX-3185. Alas, it made no difference to the print quality at all. Still washed out colours. And now, a white line down the middle too. I must have left some dirt in the unit when reassembling it. Hey ho, if new unit doesn't solve it, I'm chucking the printer and buying a new one.At a loss of why it won't print colours out nicely. Black is more or less OK.
Hi I've apply your guide on my samsung CLX3175N, and i've same problem with a 5 millimeter black line at the top and another 1/3 of the darker leaf. When i print 3/4 pages, it's better on 3 and 4 pages. i don't succeed to see which piece i must change. thanks for support and thanks for your very best videos.
+viandant5 thanks viandant5, i've unmount fuser and check it, don't seen something seems wrong. On belt, i see trace of precedent print, i've unmount it and clean it, without success. when i just do a copy without something on the window, i've trace on the page. thanks
+Antoine Girard I think it's something related to the fusers, that when are hotter after some copies work well. or may be a toner cartridge near the end of its life
Hello, I have a question : when cleaning my printer (samsung clp315) last week I removed the drum unit and noticed that the drum was full of toner. I swipe the drum and turn it but still a lot of toner. I shake it and a lot of dust (probably toner) was getting out. I am wandering if this normal or not : should we have toner inside this unit ? I tried to shake it until no more dust is getting out but it lasted for long. Should I dismanteld it and clean it as shown ? Thanks.
Your Tips are Great!!.Thanks a lot.Only what everybody should remember" toner is harmfull so don't get in contact with skin,body or inhale ".Whats about the resistor to replace?...this is a normal 100k resistor,..so how should the system short or open it when the counter for drum is full??...maybee you know it?
TheFlyer67 yes you are right, toner is harmfull but probably not carcinogenic. the fuser it's a normal thermal fuse 1/16A and it blow when you insert the drum into the machine. you'll find more information in the comment of khurram akhtar
I haven't attempted this, but my printer has lots of black and dark streaks in the photos, it appears to be leaking black poweder, hopefully this may fix it. I don't see anything wrong with the cartridges.
Thanks for your videos. I have followed your steps and it became obvious that my smudgy printing was due to waste toner everywhere after printing envelopes etc. After rebuilding I am still getting big patches of no or feint print but some decent print across the full page in places. Also, any pictures including the test page come out as a yellow smudge. Any ideas please?
Thanks for your video. I have a Samsung Clx-3185fn printer and I have a problem with color printing. I just changed all the toners but the print is only black and white. Do you have any idea where this problem could come from?
HI Viandant, thank you for the very informative and easy to follow video. I followed your instructions very closely to clean and reassemble my CLX-3185FW printer with no problem - other than heaps of waste to be emptied :( However, my printer is now printing totally black pages..? Can you tell me why this is?
Check the connection between the internal contact of the drum and the metal pin, check the supports of the charge roller and its connections, check if the drum turns freely
Hello viandant5. This is an excellent video. Thank you very much. My printer is Samsung CLX 3305w and I wanna do this procedures because it's asking me to change the drum unit and it's very expensive. Btw, I have 3 doubts before. I would ask for your help. :) The doubts are: 1. Do I need clean all these things first or if I just change the resistor the printer will work? 2. My drum unit have only 1 resistor (100k). If I change it for another one, the printer would work, ins't it? 3. Do you know the details about this resistor? I've been reading about it and it seems there are variants like 1/4w and 2w, something about 5%, ... Thanks a lot.
hice la limpieza y remanufactura de la unidad pero al quitar el eje o varilla lo hice por el lado opuesto y todas lai impresiones salen en blanco, coo podria solucionar este problema
My name is humar...I saw in the video ..that you change the fuse in blue color... so can you tell me the value of this fuse are you wearing... the 100k, resistor I already changed it..so I only need the blue fuse..Thanks buddy for you excellent information and video too...Grazie e Arrivederci...
+Humarbugo Ballesteros it's not a resistor, itìs a thermal fuse. In order to reset the drum without the thermal fuse, just put a jumper across the terminals of the resistor (small piece of copper wire will do). Close the door and plug the printer in. It will say "Initialize..." followed by a flash of lights, after which it will most probably reset itself as it is unable to "blow" the fuse (the cycle will repeat itself indefinitely). At this point switch it off (unplug power) and take out the holder with the resistor again. Take the jumper off (break the wire) and put the holder back in. Close the door and let the printer startup.
Is the drum that should 'lubricated' with toner a NEW one, or the same one (called the 'old' drum when removing it) that was taken out? I just installed a new drum assembly and my 3170 still prints ghost text & images and strange horizontal black lines on the paper.
Hello. Would you please shoot a video about how to dismantle the whole printer, especially the fuser. A paper is wrapped on the roller of the fuser and I don't know how to remove it!!
i follow the video and am now at the step where the axel is to be reinserted through the drum. i can't seem to get it past something inside. It still sticks out about 3.5 cm. and is hitting up against something. Is there any "secret" to getting it through the last 3 - 4 cm. of the drum? Have a great day! :) Edit> Oops - my bad. The video clearly states "from the drum gear side". i was trying to insert it from the other side. / Phew! That was close. It went in very easily from the drum gear side.
Good afternoon, I have for sometime a laser printer ; Samsung CLX-3175-FN and was very happy with the performance of it, but lately I think that my laser printer is due for an service checkup, sins the paper transport is giving a lot of noise and paper got jam so often. I have try to my knowledge to clean the dirt and black marking on the print copy with no result. Mean time I have now using windows 10 and the drivers for this type Samsung is no longer available, what do I have to do instead of buying another printer, can you give me some advice.??
Hi, My CLP-325W printer worked fine when I put it away for storage in 2021. Now that I want to use it again I find that after the power-up sequence completes it shows a steady red light. All toner lights are off, so toners are good. All doors are fully closed. Paper tray properly fitted (with paper). Any ideas on how to fix it? It was a new printer when I got it several years ago so I'm guessing that there will only be one resistor currently fitted. Should I fit a resistor or try the reset thing? Thanks for your video and help.
It's a general error, perhaps the drum unit or toner waste box. If moved the toner could cover the windows of the sensor so you have an error message Are there addtional information in the printer folder?
@@viandant5 Printer Folder? The printer did get shipped from the Far East to UK so internal movement of assemblies is possible but I already removed and refitted the drum unit and toner waste box. Where is this sensor window? Thanks for the reply.
@@viandant5 WOO HOO! FIXED! You're a Genius. Many thanks. So grateful.😀 Which assembly do I need to clean/lubricate in order to stop squeaking/groaning noises?
Not sure if we have the same case. I got the same problem but it finally works. I re-checked the video and realized that I put the drum on the opposite direction. See the video 4:20 that the gear part should be on the right hand side. Thanks for your video. It's awesome.
You can hola..espero ayudar..te me explain my problem I have the Samsung CLX-3305FN printer ... I begged change IMAGING UNIT (CLT-R406) proceeded to change with a new ... no longer gives any message on the printer LED red and green sensor now ... the problem is that sending to print a document printer ... makes the whole process, but does not print out nada..la completely blank sheet .- .. could you tell me what would be the possible causes of this problem .. .Thanks in advance for the help
+Pcs Home I think the drum unit is defective, probably some contact with the printer or the ground contact inside the drum. also you can remove it and reinstall again
mi impresora en una CLP 310, al imprimir deja marca de lo que imprimi, se puede correjir siguiendo las instrucciones de este video? Muchas gracias por su atencion. Atte. Hideki Nakashima
Hello viandant5. This is an excellent video. Thank you very much. My printer is Samsung CLX 3305w and I wanna do this procedures because it's asking me to change the drum unit and it's very expensive. Btw, I have 3 doubts before. I would ask for your help. :)
@@viandant5 my foam roller is almost broken too but I still have it cleaned and installed back. The printer seems working now. Could let me know what function the foam roller is?
+Jackson Boo It cno, it does not work in that way. the quality of a drum depends on the shape of its outer layer and light fatigue. cleaning a drum does not restore the outer layer
Well, it is printing very well now. However it seems to be making scraping sounds inside. i didn't see any suggestions to oil the drum axel - which is what it sounds like... Should i try this? Otherwise it seems to be printing just fine. Have a super day and thanks for such a wonderful video! :)
I followed the instructions. After reassembling the 3185fw prints only blank pages. The drum runs freely without any problem. Any clue what the issue can be? thanks
Hello friend, I have a big problem, clean the unit as mention it, but after installing all print command and all the leaves are blank, if I take the same copies, always leaves blank, nothing is printed.
+Jesús Casillas it may be a problem of bad contacts with charge roller, or with the internal ground contact of the drum. try disassemble and reassemble again the drum unit
Hi I work on it as your instruction. after assembly and print there are no image in paper. blank paper out. could you advise me how to image drum rebuilding?
@@viandant5 can you explain more detail for me or reference video in youtube? my printer is SL-C433. same problem was happen after dissembly and assembly in 3 time. can I check image drum roller broken? plz explain me thank you.
@@user-sb4dk2vy4d it's difficult to say exactly without checking the drum. may be the internal contact inside the drum cylinder is broken or bent, may be there is a faulty contact somewhere
I also printed blank pages. I had put the gear side of the QPC on the left. The gear side should be on the right side. Once the QPC gear was on the correct side, I was able to print again.
Followed these instructions because my Samsung CLP365's drum needed to be reset. All seemed to go well. Put the printer back together and the status light went green, but whenever I try to print, the green status light just flashes slowly. Printer never starts. Just sits there for hours flashing the light. Any ideas what went wrong?
viandant5 OK, I installed it. It just says "Status: Warning" and then below it always says "Warming up. Please wait." Doesn't tell me anything else in detail. Wish it did. When I try to print anything, the little status popup appears and says "Preparing Print Job", and the status light on the printer starts blinking, and that's where it stays. Even the popup stays on the screen.
Hello viandant5, I just watched your video. My Xpress 460FW only has a 100k resistor. No thermal fuse. Do I replace this resistor and also solder in a piece of copper wire across it? Thanks! Gary
I cleaned my Samsung CLX 3175 drum unit as per the video. On reassembly the drum turns freely counter clockwise but jambs up in the clockwise direction (as shown in the video. I can't figure out why - has anyone else had this problem and is there a fix?
Thank you very much @viandant5 ! Awesome videos you're the man! But still have a question: The waste toner paticles got into the lens array glass, can i clean it? (samsung clp 315)
i've changed to the new resistor and do not work , i done the jump with single copper wire, and not work to. In Brazil the drum unit it's very very expensive , please help me
+Joao Simoes if the drum does not reset in any way, I think the problem is not the drum or at least it's not the fuse. i would try checking the connection between drum and printer
Hi, i have followed your guide but i guess i have did something wrong. I tried printing a test page, but it only prints on the left most side for about 0.5cm thick. All the colors are there so the result is a heavy colored one. Any way to fix?
+Jepher Chang I think a component of the drum unit is out of position, may be the rod lens array. I suggest you to dismantle and reassemble again the drum unit.
+Jepher Chang I think the rod les array is broken, dirty or out od position or the drum is not reassemble correctly and the developer roller is not in contact with the drum surface.
Hello all, I have a Samsung C460W printer with initial OPC (Imaging Unit: 6649/16000 (Image(s)/Life)) I have some dirty prints so I clean the printer and OPC according to this procedure. The problem is that after doing that all printed pages are blank pages, there is no errors in the printer, everything seems to be normal. I tried dissembling and assembling the OPC again but nothing changes... Can someone help me to solve this issue? I have check in the comments that other people face same problem... can someone share any ideas? Thanks in advance!
I have clp 325 original toner no chip sometime it NOT found magenta cartridge sometime it found :: status "magenta cartridge not install please install " how to fix it
JeeRa Wit it's a starter cartridge. starter cartidges have no chip. do not remove the cartridge drom the printer or you may have problems. to fix it you can only install a chip into the cartridge
may be a contact between the printer and the drum unit is broken or out of position. try disassembling and reassembling the drum unit. verify the position of the charge roller
hello, thanks for this excellent video! my clx-3305fn gives error about "drum unit", it says "change drum unit with new one". I have been using this drum unit since I purchased the printer 1 year ago. I think I have to reset its chip and I took out the chip on drum unit, it has one brown resistor as you mention about initial drum units. in the video, you removed green resistor and put a new one there. What should I do now? should I put a resistor behind the brown resistor like in the video? but what is the resistor's name or value to put behind the brown resistor? if you tell me its specification then I can find it in my country, in some electronic shop. THANKS A LOT!
do not remove the brown resistor, in your case solder the new component. put the component behind the brown resistor like in the video. I think it's not possible to find this component in some electonic shop, it's an integrated not a simple resistor
viandant5 thanks for the quick reply. should I put the green component behind the brown resistor like in the video? I searched for info on russian forums and found this: www.chip.ho.ua/fuse.html and a photo about the compoent here: www.chip.ho.ua/reset_iu_samsung_clt-r409.jpg Fuses pico fuse 1 / 16A, what do you think? Also check this page: be.farnell.com/littelfuse/0251-062mat1l/fuse-quick-blow-62ma/dp/9921931 I think I have found it, here is the link: www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20150118012339&SearchText=r409+drum+reset+chip or here is another link: www.westfloridacomponents.com/F078PE04/1%26%2347%3B16A+Picofuse+Littelfuse+0251.062MRT1.html
viandant5 thanks a lot! after 2 days of search on internet, I have learned that there are 2 types of littelfuse. Type1 (0.0625A 125V) is to use on 110V city electricity. Type2 (0.0625A 250V) is to use on 220V city electricity. For example, in my country, we use 220V electricity so I think I should buy a littelfuse 0.0625A 250V version. I will order it and try it, I will let you know about the result.
viandant5 yes, it worked !!! I soldered the green littelfuse (0.0625A = 1/16 A, 250V version) behind the brown resistor on drum chip and I got rid of the "replace new imaging unit" error of my clx-3305fn printer! yayyy!!! :)))
Didn't work because I still get ghost images from the previous page. Also, when I turned over the drum, a lot of toner fell out that I wasn't expecting.
Help . I got the drum unit out of the printer and cleaned it but when I put it back the printer prints only the right half of the page , the left side of the page is blank. Anyone knows how to fix this ?
Hello! An email address can I ask? I have a picture that I report the error to produce. I would like to ask for advice what to do against the error. Thanks for the answer!
hi there - i have a samsung clp -315; recently I noticed it prints pages with horizontal lines and smudges in black and sometimes yellow the whole width of the page. When I print a 2nd page, it ghosts the previous page on the new page as well. I have followed your videos on how to clean the transfer belt and image drum, and installed new toner cartridges, but the problem persists. Any chance you could advise on what I can do to fix this issue? Here is a link to show my issue: imgur.com/gallery/WfH19jO
@@viandant5 thanks. I will look to find a replacement drum. Should I replace the transfer belt at the same time? Any tips on how to prevent damaging the drum unit ?
@@patrickx7876 It's not necessary to replace the belt, However without checking the printer I can't be sure it's a drum problem. To prevent the consumption of the drum do not turn on and off the printer frequently, the printer must be in a dry environment
Many thanks for this video!
My Samsung C480 had very dirty prints. On inspection the drum was also very dirty. First cleaned the transport belt, but that did not help. It turned out that the toner waste reservoir in the drum unit was completely filled to the rim. So it couldn't clean the drum anymore. I removed the roller and shook out all toner waste. Cleaned the drum unit and voila: happy clean prints!
Wow, it worked! It took awhile for the white lines to get worked out, but after 10 copies or so, they are gone. Thanks so much!!
Thank you very much for this video. I was able to fix "image ghosting" on a Samsung CLP-315W by following your instructions to clean the charge roller with water. Imaging Unit was only at 1100pgs, 84% life remaining, but living in dry climate(Denver, CO) made the charge roller(and foam roller) ineffective at removing excess image toner.
Imaging unit drum was diagnosed as culprit by measuring 7.5 vertical inches between original image and ghosted image. Again, 10,000 thanks.
Thank you for this comment. I have the same problem and did not know what to fix it. I will try this
Original factory units that come with the printer do not have the thermal fuse anyways. In order to reset the drum without the thermal fuse, just put a jumper across the terminals of the resistor (small piece of copper wire will do). Close the door and plug the printer in. It will say "Initialize..." followed by a flash of lights, after which it will most probably reset itself as it is unable to "blow" the fuse (the cycle will repeat itself indefinitely). At this point switch it off (unplug power) and take out the holder with the resistor again. Take the jumper off (break the wire) and put the holder back in. Close the door and let the printer startup.
Tested on CLX-3300 series with CLT-R406 drum.
Hey, You are genius !
«How to remove and clean Samsung Transfer Belt CLP-365» + «How to Clean an OPC Drum for Laser printer/Copier» + «CLP310 320 360 CLX Drum unit Rebuilding Instructions» helped me to diagnostic my CLX-3175N ghosted pic (from top printing) on on the bottom of each page, and was spaced to 188mm.
I read forums, but was not sure if it was the transfert belt or the OPC Drum.
Those both parts are quite expensive : ~ 120€ for both, not sure it worth it !
I did the cleaning like you said on both items, on the tranfert belt, it didn't change.
But I for the OPC drum, I well listen your precious comments and found after the 1st rebuild a better printing, but still some few ghost pic on bottom.
I pushed a bit all the wiper blade for enable it better fit the OPC Drum.
And it worked... !!
I know that It won't be lasting, but I know now for sure that's it's the OPC Drum, the wiper blade exactly.
[EDIT] : I forgot also to mention excellent tuto «Toner Cartridge Printing Defects: Causes and Solutions».
Many thanks !
a ghosted print may be related to the drum or to the fuser unit. the distance of 188 mm is related to the drum but I don't think it's a wiper blade problem. Probably you have to change the OPC drum
Hehe... Just have a look when I gently pushed the wiper blade in the drum direction in a way of having a better contact on the drum you can see spectacular result on the right :
imgur.com/ssh7i6P or i.imgur.com/ssh7i6P.jpg
Deprives me of a doubt : I also changed the black toner cartridge. I don't remember when in all those repair process (quantity
the space of 188 mm is related to the drum the developer roller is 26 mm but the ghost images are related to toner cartridge too. the developer roller is the roller covered with toner you can see on the toner cartridge
I couldn't rotate the drum clockwise after rebuilding it, and the tip given here @3:58 saved my day.
Thank you dude!
What tip?I can not turn it upwards also? lubricating the drum with toner?
@@alfasud1972 That's right, with a clean fabric and a bit of toner powder (gotta be specific for those who aren't quite computer savvy)
Hi viandent sorry couldnt find my original post but u asked me to respond if I had any luck, well i did! I was getting repeated black lines a long my pages dispite changing fuser unit and cleaning drum unit. Well I completely swapped te drum unit out, no more black lines! Clp365w. Yay! So I'm assuming drum unit must have been "damaged" in some way as image counter was only at 1982 not sure but working perfectly now. Thanks for yr help and keep the informative vids coming :)
Thank you for the video. I have a Samsung C460W that began to have faded printing. Cleaned out the waste toner tank, the transfer belt, and finally the image drum per your videos. Wow, a LOT waste toner in all those components! I found it best to do this job outside on a nice day. Used an electric leaf blower on low to blow everything out. Not sure why cleaning the image drum assembly helped, but it did! I am thinking it is the cleaning of the charge roller and the light rod that actually makes the difference. All of the other cleaning is just to get rid of the excess waste toner, which must be disposed of before the containers become full.
did you change/replace the resistor too?
@@viauyeung No, I did not. There is a method to reset the laser printer to set the counters back to zero (if I remember correctly).
is there a remaining toner in the drum unit that need to be cleaned?
worth noting, for anyone who doesn't know, when replacing or refilling/resetting/cleaning the drum and/or toners, you should grab a ziploc bag and also empty the collection cassette into it, making sure to wear a face mask and gloves for protection against the toner dust. make sure to completely close the ziploc bag afterwards and dispose of appropriately. Most of all, don't be put off by the fact the toner in the bag will resemble mold lol.
Modern toner is soy ink. It's not nearly as bad as you're making it out to be.
@@EvanCarrollTheGreat Patently false.
Most modern toners are composed of 85-95% plastic. The other 5-15% is comprised of ground silica, iron, chromium and zinc.
What you're thinking about, is inkjet cartridges. Not even close to being the same thing. Regardless, you don't even want to have inkjet liquids touching your skin because they also contain petroleum. Petroleum is a skin irritant.
I was going to trash my CLP315 because it wouldn't be economical to fix it. This was very helpful and the thing is printing perfectly now. Thank You. The one thing I can't figure out is how in the world the reset fuse replacement can be figured out by the printer that it just hasn't been lifted and resoldered. That is a new one for me.
+Dick Wooten the new printers are already resetted, you don't need to reset the drum so there is no fuse in the starter drums
+viandant5 No problem. I was just remarking that the videos that I have seen are strange because having to replace one thermal fuse or resistor with another and the printer somehow knows that it is another one of the same value is a strange concept for a guy who was a radio technician for a lot of years. Thanks again.
@@Dickwooten Looks like he added a thermal fuse in parallel which has little to no resistance may as well soldered a piece of fuse wire across it
@@Dickwooten When the printer sees a drum unit with very little resistance, it assumes a new one has been installed. It then blows the fuse by passing a lot of current through it. when this fuse blows, the 100k resistor is the only current path left. The printer now knows it has successfully "started the lifecycle" of that toner. It has no way of recognizing the toner (or a new one) besides a low resistance path that became high resistance after trying to initialise it.
CLX DRUM SHAFT INSERTION: Samsung seem to use the same drum design for many of their printers esp CLX series but bearing different Model numbers. The most important point in dismantling and removing the drum shaft is a result of the internal electrical contacts that while rubbing on the shaft, allow a clean shaft to pass easily through them in only one direction. This is from the end bearing the gear (and internal contacts) towards the opposite end. Unfortunately this is not mentioned in this "Remanufacture" procedure but can be seen by carefully comparing both the disassembly and assembly segments of the video.
I found that my imaging unit had an overflowing toner that stacks up from the top. Following your guide, I cleared out the waste toner tank (there was a TON of powder). Let's see what happens.
Dziekuje Panu serdecznie.Uratowal Pan moja drukarke. Cudownie drukuje.Dziekuje.
Excellent video. I followed the instructions and did pretty much what you did on the video on my CLX-3185. Alas, it made no difference to the print quality at all. Still washed out colours. And now, a white line down the middle too. I must have left some dirt in the unit when reassembling it. Hey ho, if new unit doesn't solve it, I'm chucking the printer and buying a new one.At a loss of why it won't print colours out nicely. Black is more or less OK.
Check/Clean the Laser unit under the drum in the Bottom (papertray pulled out) If rhat doesnt Help, Change the OPC of the Drum
Excelent video! Thanks!
Thank you for sharing. Had all that I needed to know to fix my outdated printer.
Hi I've apply your guide on my samsung CLX3175N, and i've same problem with a 5 millimeter black line at the top and another 1/3 of the darker leaf. When i print 3/4 pages, it's better on 3 and 4 pages. i don't succeed to see which piece i must change. thanks for support and thanks for your very best videos.
+Antoine Girard I would check the fusers, or the belt
+viandant5 thanks viandant5, i've unmount fuser and check it, don't seen something seems wrong. On belt, i see trace of precedent print, i've unmount it and clean it, without success. when i just do a copy without something on the window, i've trace on the page. thanks
+Antoine Girard I think it's something related to the fusers, that when are hotter after some copies work well. or may be a toner cartridge near the end of its life
Super erklärt spart viel Geld Danke
тупо -просто и легко.. но все сделал правильно.. молодца
I found the problem ... the box with colored symbols has two windows - they have to be cleaned inside ... and ready. I lost a few days, but it works!
Hello, I have a question : when cleaning my printer (samsung clp315) last week I removed the drum unit and noticed that the drum was full of toner. I swipe the drum and turn it but still a lot of toner. I shake it and a lot of dust (probably toner) was getting out. I am wandering if this normal or not : should we have toner inside this unit ? I tried to shake it until no more dust is getting out but it lasted for long. Should I dismanteld it and clean it as shown ? Thanks.
The waste toner is contained inside the drum unit, so it's normal to have toner in the drum unit
@@viandant5 OK so it is wated toner, then I can clean it, this will not affect negatively the printing ?
@@fredericpageot3506 no, you can remove it. Or even let it there, it does not change nothing
Good video very informative.
Should've watched this before I tried to fix it myself...
Your Tips are Great!!.Thanks a lot.Only what everybody should remember" toner is harmfull so don't get in contact with skin,body or inhale ".Whats about the resistor to replace?...this is a normal 100k resistor,..so how should the system short or open it when the counter for drum is full??...maybee you know it?
TheFlyer67 yes you are right, toner is harmfull but probably not carcinogenic.
the fuser it's a normal thermal fuse 1/16A and it blow when you insert the drum into the machine. you'll find more information in the comment of khurram akhtar
coal miners stay yeas inside the mine
I haven't attempted this, but my printer has lots of black and dark streaks in the photos, it appears to be leaking black poweder, hopefully this may fix it. I don't see anything wrong with the cartridges.
Thanks for your quick reply. I will check that out.
Thanks for your videos. I have followed your steps and it became obvious that my smudgy printing was due to waste toner everywhere after printing envelopes etc. After rebuilding I am still getting big patches of no or feint print but some decent print across the full page in places. Also, any pictures including the test page come out as a yellow smudge. Any ideas please?
may be one of the toner cartridge is near the end of its life. check if the developer rollers of the toner cartridges are fully covered with toner
Muchas gracias me ayudo mucho tu video.
Thanks for your video. I have a Samsung Clx-3185fn printer and I have a problem with color printing. I just changed all the toners but the print is only black and white. Do you have any idea where this problem could come from?
HI Viandant, thank you for the very informative and easy to follow video. I followed your instructions very closely to clean and reassemble my CLX-3185FW printer with no problem - other than heaps of waste to be emptied :( However, my printer is now printing totally black pages..? Can you tell me why this is?
Check the connection between the internal contact of the drum and the metal pin, check the supports of the charge roller and its connections, check if the drum turns freely
Hello viandant5.
This is an excellent video. Thank you very much.
My printer is Samsung CLX 3305w and I wanna do this procedures because it's asking me to change the drum unit and it's very expensive. Btw, I have 3 doubts before. I would ask for your help. :)
The doubts are:
1. Do I need clean all these things first or if I just change the resistor the printer will work?
2. My drum unit have only 1 resistor (100k). If I change it for another one, the printer would work, ins't it?
3. Do you know the details about this resistor? I've been reading about it and it seems there are variants like 1/4w and 2w, something about 5%, ...
Thanks a lot.
Cori Fung, you have a starter drum started drums do not have the fuse. you have to insert the new reset fuse near the colored fuse
hice la limpieza y remanufactura de la unidad pero al quitar el eje o varilla lo hice por el lado opuesto y todas lai impresiones salen en blanco, coo podria solucionar este problema
My drum makes some noise after replacing the OPC... Do I need to lube the shaft before pushing it through the OPC? 🤔🤷♂️
It might depend fromn the metal shaft, you can use a bit of grease
My name is humar...I saw in the video ..that you change the fuse in blue color... so can you tell me the value of this fuse are you wearing... the 100k, resistor I already changed it..so I only need the blue fuse..Thanks buddy for you excellent information and video too...Grazie e Arrivederci...
+Humarbugo Ballesteros it's not a resistor, itìs a thermal fuse. In order to reset the drum without the thermal fuse, just put a jumper
across the terminals of the resistor (small piece of copper wire will
do). Close the door and plug the printer in. It will say "Initialize..."
followed by a flash of lights, after which it will most probably reset
itself as it is unable to "blow" the fuse (the cycle will repeat itself
indefinitely). At this point switch it off (unplug power) and take out
the holder with the resistor again. Take the jumper off (break the wire)
and put the holder back in. Close the door and let the printer startup.
Is the drum that should 'lubricated' with toner a NEW one, or the same one (called the 'old' drum when removing it) that was taken out? I just installed a new drum assembly and my 3170 still prints ghost text & images and strange horizontal black lines on the paper.
the lubrication only help the drum to rotate freely. probably you problem is related to fusers or toner cartridges
Hello. Would you please shoot a video about how to dismantle the whole printer, especially the fuser. A paper is wrapped on the roller of the fuser and I don't know how to remove it!!
+Morhaf S I've done a video, search in this channel "how to remove transfer unit samsung clp 310"
do not even touch the blades with finger , they will deform and u can bin them
Hi friend. Where can i find the foam / cleaning roller? My printer is a Samsung CLX 3185. I've been trying to find it but whitout any success.
I think nobody sells it. You can remove it fro another old drum unit
i follow the video and am now at the step where the axel is to be reinserted through the drum. i can't seem to get it past something inside. It still sticks out about 3.5 cm. and is hitting up against something. Is there any "secret" to getting it through the last 3 - 4 cm. of the drum?
Have a great day! :)
Edit> Oops - my bad. The video clearly states "from the drum gear side". i was trying to insert it from the other side. / Phew! That was close. It went in very easily from the drum gear side.
Good afternoon,
I have for sometime a laser printer ; Samsung CLX-3175-FN and was very happy with the performance of it, but lately I think that my laser printer is due for an service checkup, sins the paper transport is giving a lot of noise and paper got jam so often. I have try to my knowledge to clean the dirt and black marking on the print copy with no result. Mean time I have now using windows 10 and the drivers for this type Samsung is no longer available, what do I have to do instead of buying another printer, can you give me some advice.??
where the paper is jamming? in the paper cassette? may be the pick up roller are worn or dirty, try to clean them with alcohol.
Good job!
Hi, My CLP-325W printer worked fine when I put it away for storage in 2021. Now that I want to use it again I find that after the power-up sequence completes it shows a steady red light.
All toner lights are off, so toners are good. All doors are fully closed. Paper tray properly fitted (with paper).
Any ideas on how to fix it?
It was a new printer when I got it several years ago so I'm guessing that there will only be one resistor currently fitted. Should I fit a resistor or try the reset thing?
Thanks for your video and help.
It's a general error, perhaps the drum unit or toner waste box. If moved the toner could cover the windows of the sensor so you have an error message Are there addtional information in the printer folder?
@@viandant5 Printer Folder?
The printer did get shipped from the Far East to UK so internal movement of assemblies is possible but I already removed and refitted the drum unit and toner waste box.
Where is this sensor window?
Thanks for the reply.
@@unreasonable4rce Clean the windows of the waste toner box
@@viandant5 WOO HOO! FIXED! You're a Genius. Many thanks. So grateful.😀
Which assembly do I need to clean/lubricate in order to stop squeaking/groaning noises?
@@unreasonable4rce May be the metal axle of the drum, or the bushings of the fusers
Hi, thank you for the video. It’s quite helpful. I replaced the drum on my printer but now it prints blank sheet. Do you know why?
Check the contacts inside the drum, check the continuity between the metal rod and the surface of the drum
Not sure if we have the same case. I got the same problem but it finally works. I re-checked the video and realized that I put the drum on the opposite direction. See the video 4:20 that the gear part should be on the right hand side. Thanks for your video. It's awesome.
Hi Viandant! For the same problem, can I do this same procedure, for SAMSUNG XPRESS-460W? Thanks!
yes, it's the same
Hi, I have a problem by installing the drum gear.
The drum gear doesn´t turn clockwise. But I dont kno why, other direction is ok.
you have to lubricate the drum with toner. follow the video
You can hola..espero ayudar..te me explain my problem
I have the Samsung CLX-3305FN printer ... I begged change IMAGING UNIT (CLT-R406) proceeded to change with a new ... no longer gives any message on the printer LED red and green sensor now ... the problem is that sending to print a document printer ... makes the whole process, but does not print out nada..la completely blank sheet .- .. could you tell me what would be the possible causes of this problem .. .Thanks in advance for the help
+Pcs Home I think the drum unit is defective, probably some contact with the printer or the ground contact inside the drum. also you can remove it and reinstall again
thanks , very useful
mi impresora en una CLP 310, al imprimir deja marca de lo que imprimi, se puede correjir siguiendo las instrucciones de este video?
Muchas gracias por su atencion.
Atte. Hideki Nakashima
Yes, but that defect can be related to fusers too
Hello viandant5.
This is an excellent video. Thank you very much.
My printer is Samsung CLX 3305w and I wanna do this procedures because it's asking me to change the drum unit and it's very expensive. Btw, I have 3 doubts before. I would ask for your help. :)
+Thiago Mouço hi, which doubts?
Where i can get the foam roller below the rubber roller. My foam roller is broken.
You can only take it from another used cartridge
@@viandant5 my foam roller is almost broken too but I still have it cleaned and installed back. The printer seems working now. Could let me know what function the foam roller is?
I assume your drum has been used for quite awhile. By cleaning it, does it help to last for even longer or it will just die after awhile.
+Jackson Boo Any ink reset guide?
+Jackson Boo cleaning the drum does not help to last longer. it only improve print quality
+viandant5 As the drum get older, the quality drop. By improving the quality = lasting longer? Or it just doesnt work that way?
+Jackson Boo It cno, it does not work in that way. the quality of a drum depends on the shape of its outer layer and light fatigue. cleaning a drum does not restore the outer layer
+viandant5 Ahh! I see, Thank you for the knowledge :D
In CLX-3305W not work ! ...replace or install waste toner container. What now ?
the waste container is the first step. then remove the toner cartridges, and the drum
Well, it is printing very well now. However it seems to be making scraping sounds inside. i didn't see any suggestions to oil the drum axel - which is what it sounds like... Should i try this? Otherwise it seems to be printing just fine.
Have a super day and thanks for such a wonderful video! :)
+Frederick Frazelle yes, you can use a bit of lubricant oil or conductive grease on the drum axle. have a godd day you too
I followed the instructions. After reassembling the 3185fw prints only blank pages. The drum runs freely without any problem. Any clue what the issue can be? thanks
look at the contacts on the side of the drum unit, disassemble and reassemble the drum unit again
Did not help. I noticed there is a green gear at the front right of this unit. It rotates only in one direction...?
near the charge roller? blank pages may be related to the charge roller
Sir is there a way to reset drum unit of Proxpress M3835nd
I never hear that machine, sorry I can't help you
Hello friend, I have a big problem, clean the unit as mention it, but after installing all print command and all the leaves are blank, if I take the same copies, always leaves blank, nothing is printed.
+Jesús Casillas it may be a problem of bad contacts with charge roller, or with the internal ground contact of the drum. try disassemble and reassemble again the drum unit
Did it help? All connections seem to be good. I even used contact spray. No change. :(
Sorry. What is the value of the second resistance?
Thank you very much!!!
What liquid was the green colored drum lubricated with?
It's toner powder
I have checked my printer CLP-365-Roller CLT-R406 but there is no install any resistor , what can I do ?
probalby is a starter drum. install the resistor
Hi
I work on it as your instruction.
after assembly and print there are no image in paper. blank paper out.
could you advise me how to image drum rebuilding?
May be the contact inside the printer. check the charge roller too
@@viandant5 can you explain more detail for me or reference video in youtube? my printer is SL-C433.
same problem was happen after dissembly and assembly in 3 time.
can I check image drum roller broken? plz explain me thank you.
@@user-sb4dk2vy4d it's difficult to say exactly without checking the drum. may be the internal contact inside the drum cylinder is broken or bent, may be there is a faulty contact somewhere
thank you very very much.
I fix it as your advice.
I also printed blank pages. I had put the gear side of the QPC on the left. The gear side should be on the right side. Once the QPC gear was on the correct side, I was able to print again.
Excellent contribution COLLEAGUE you know how to reset the SHUTTLE AND SAMSUNG 3165W FUSOR OF THANKS
+SHARP COPIADORAS SHARP Hi, sorry I don't know how to reset that fuser
BARÁT KÖSZÖNJÜK keresd , ha megtaláljuk a megosszák egymással .. mindig és örökké .....
I see a little transparent tube damaged, or will that gave wing to light unit?
+Jesús Casillas probably you mean the rod lens array. if it's damage it will not reflect the image on the drum properly
Hi, after changing the fuse I got rid of "red light" but the Smart Panel says: "warming up, please wait"
Dominika Bieńkowska I think you have problem to the fuser unit. the "warming up" is related to the fuser rollers
viandant5 Problem solved, the fuse wasnt tolally burnt, took it out, now all works perfect! Thank you for great instructions!
Followed these instructions because my Samsung CLP365's drum needed to be reset. All seemed to go well. Put the printer back together and the status light went green, but whenever I try to print, the green status light just flashes slowly. Printer never starts. Just sits there for hours flashing the light. Any ideas what went wrong?
+wlcgblog you can view the status of the printer in Easy Printer Manager. If not already download, you can find it in the Samsung Download Center.
viandant5 OK, I installed it. It just says "Status: Warning" and then below it always says "Warming up. Please wait." Doesn't tell me anything else in detail. Wish it did.
When I try to print anything, the little status popup appears and says "Preparing Print Job", and the status light on the printer starts blinking, and that's where it stays. Even the popup stays on the screen.
+wlcgblog probably the fuse you use to reset the drum is wrong. remove that fuse and try insert the drum unit without that fuse
viandant5
Still nothing. Just sits there, "warming up" forever. Thinking it's time to have a funeral.
+wlcgblog I think it's related to the drum chip. this defect may happen when the fuse does not blow
Olá amigos! Agradeço pela ajuda. Comigo funcionou o procedimento utilizado pelo Sergei Posokhov.
Impressora Samsung CLX 3305w
e ai cara blz, vc usou qual fusível térmico
Hello viandant5, I just watched your video. My Xpress 460FW only has a 100k resistor. No thermal fuse. Do I replace this resistor and also solder in a piece of copper wire across it?
Thanks!
Gary
The starter drum unit has no thermal fuse . let the resistor there and add the thermal fuse
I cleaned my Samsung CLX 3175 drum unit as per the video. On reassembly the drum turns freely counter clockwise but jambs up in the clockwise direction (as shown in the video. I can't figure out why - has anyone else had this problem and is there a fix?
+Curtis Nowosad first to install the drum, you have to lubricate the drum with a bit of toner (minute 3.55)
E ring remove that’s focking hard
I have a CLX-3180, which prints black fine, but the colors have become very faded over time. Will this procedure help my problem?
+poodleguts may be, but In this case probably the problem is one of the color toner cartridge
is a 56k resistor can change whit similar valor
Thank you very much @viandant5 ! Awesome videos you're the man! But still have a question: The waste toner paticles got into the lens array glass, can i clean it? (samsung clp 315)
yes, here you'll find instructions ua-cam.com/video/cbDyxocOYGA/v-deo.html
You're awesome, thanks a lot.
Thanks Really helped
you forget to tell put litle pownder in the drum surface
you can lubricate the drum with a bit of toner powder 3:54
the resistor value changes that put it
i've changed to the new resistor and do not work , i done the jump with single copper wire, and not work to. In Brazil the drum unit it's very very expensive , please help me
+Joao Simoes if the drum does not reset in any way, I think the problem is not the drum or at least it's not the fuse. i would try checking the connection between drum and printer
Hi, i have followed your guide but i guess i have did something wrong. I tried printing a test page, but it only prints on the left most side for about 0.5cm thick. All the colors are there so the result is a heavy colored one. Any way to fix?
+Jepher Chang I think a component of the drum unit is out of position, may be the rod lens array. I suggest you to dismantle and reassemble again the drum unit.
tried dismantling and reassembling it. now the dirt i want to remove is back. but still no text/image
+Jepher Chang are you sure the defect is related to the drum?
+viandant5 not sure. but that's the only thing I have touched. I still have inks about 50+%
+Jepher Chang I think the rod les array is broken, dirty or out od position or the drum is not reassemble correctly and the developer roller is not in contact with the drum surface.
I did not lubricate the drum with powder, did I fuck it up? Lol seems to work fine
If it works, it's ok
Hello all,
I have a Samsung C460W printer with initial OPC (Imaging Unit: 6649/16000 (Image(s)/Life))
I have some dirty prints so I clean the printer and OPC according to this procedure.
The problem is that after doing that all printed pages are blank pages, there is no errors in the printer, everything seems to be normal. I tried dissembling and assembling the OPC again but nothing changes... Can someone help me to solve this issue?
I have check in the comments that other people face same problem... can someone share any ideas?
Thanks in advance!
check the continuity between the drum and its metal shaft, check the conbtacts between the drum and the printer
What is the resistor youve added
You can find it in several web stores
@@viandant5 I meant what is the resistance value of the resistor
@@NordenEngineering ua-cam.com/video/MSPsVQdUr5M/v-deo.html one of them is 56 ohm the other is 200 k ohm
I have clp 325 original toner no chip sometime it NOT found magenta cartridge sometime it found :: status "magenta cartridge not install please install " how to fix it
JeeRa Wit it's a starter cartridge. starter cartidges have no chip. do not remove the cartridge drom the printer or you may have problems. to fix it you can only install a chip into the cartridge
All toner cartridge no chip but not found magenta only
But sometime it found i can print normal
JeeRa Wit all your cartridges are starter cartridges. probably magenta cartridge is near the end of its life, starter cartridges have not many toner
Thank you so much . Can i use clp-325 cartridge replace in clp-365?
i cleaned the drum unit for samsung xpress c460w and aftter closing the printer is printing blank pages pls ssist
may be a contact between the printer and the drum unit is broken or out of position. try disassembling and reassembling the drum unit. verify the position of the charge roller
hello, thanks for this excellent video! my clx-3305fn gives error about "drum unit", it says "change drum unit with new one". I have been using this drum unit since I purchased the printer 1 year ago. I think I have to reset its chip and I took out the chip on drum unit, it has one brown resistor as you mention about initial drum units. in the video, you removed green resistor and put a new one there. What should I do now? should I put a resistor behind the brown resistor like in the video? but what is the resistor's name or value to put behind the brown resistor? if you tell me its specification then I can find it in my country, in some electronic shop. THANKS A LOT!
do not remove the brown resistor, in your case solder the new component. put the component behind the brown resistor like in the video. I think it's not possible to find this component in some electonic shop, it's an integrated not a simple resistor
viandant5 thanks for the quick reply. should I put the green component behind the brown resistor like in the video? I searched for info on russian forums and found this:
www.chip.ho.ua/fuse.html and a photo about the compoent here: www.chip.ho.ua/reset_iu_samsung_clt-r409.jpg
Fuses pico fuse 1 / 16A, what do you think?
Also check this page:
be.farnell.com/littelfuse/0251-062mat1l/fuse-quick-blow-62ma/dp/9921931
I think I have found it, here is the link:
www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20150118012339&SearchText=r409+drum+reset+chip
or here is another link:
www.westfloridacomponents.com/F078PE04/1%26%2347%3B16A+Picofuse+Littelfuse+0251.062MRT1.html
murat büyükdinç yes, you should put the green component behind the brown resistor. the russian forum is correct
viandant5 thanks a lot! after 2 days of search on internet, I have learned that there are 2 types of littelfuse. Type1 (0.0625A 125V) is to use on 110V city electricity. Type2 (0.0625A 250V) is to use on 220V city electricity. For example, in my country, we use 220V electricity so I think I should buy a littelfuse 0.0625A 250V version. I will order it and try it, I will let you know about the result.
viandant5 yes, it worked !!! I soldered the green littelfuse (0.0625A = 1/16 A, 250V version) behind the brown resistor on drum chip and I got rid of the "replace new imaging unit" error of my clx-3305fn printer! yayyy!!! :)))
Didn't work because I still get ghost images from the previous page. Also, when I turned over the drum, a lot of toner fell out that I wasn't expecting.
ghost images are probably related to the fusers, not to the drum.
Help . I got the drum unit out of the printer and cleaned it but when I put it back the printer prints only the right half of the page , the left side of the page is blank. Anyone knows how to fix this ?
the name of the fuse to buy it on the Internet?
+VideoBlog 73 you can find it on ebay or searching with google "reset Samsung clp"
could you provide a link to the fuse? you are welcome.
+VideoBlog 73 for example this: www.ebay.it/itm/4x-Drum-Reset-Fuse-for-Samsung-CLP-310-CLP-315-N-W-CLX-3170-3175-FN-FW-series-/121193047010
1:24
dust clean the fuser and install without
dust? urgent response. Thank you
what do you mean? Why dust on the fuser?
viandant5 express c460fw
thanks u
Eu apenas fiz a limpeza e minha impressora agora só imprime papel em branco alguém pode me ajudar?
Hello! An email address can I ask? I have a picture that I report the error to produce. I would like to ask for advice what to do against the error. Thanks for the answer!
link.accessori@libero.it, you can find it in the description of the video
hi there - i have a samsung clp -315; recently I noticed it prints pages with horizontal lines and smudges in black and sometimes yellow the whole width of the page. When I print a 2nd page, it ghosts the previous page on the new page as well. I have followed your videos on how to clean the transfer belt and image drum, and installed new toner cartridges, but the problem persists. Any chance you could advise on what I can do to fix this issue?
Here is a link to show my issue: imgur.com/gallery/WfH19jO
The cleaning of the drum unit and the transfer belt is useess if the drum unit is defective.. It seems to me a problem to the drum unit
@@viandant5 thanks. I will look to find a replacement drum. Should I replace the transfer belt at the same time? Any tips on how to prevent damaging the drum unit ?
@@patrickx7876 It's not necessary to replace the belt, However without checking the printer I can't be sure it's a drum problem. To prevent the consumption of the drum do not turn on and off the printer frequently, the printer must be in a dry environment