Top, hab nach einem anderen Video nur das mit der Alufolie gemacht, was nichts gebracht hat. Aber der Hinweis mit den Zählerständen zurücksetzen war GOLD WERT!!!!!! DANKE
A+ video! For anyone with trouble removing the wire clip: I had to use pliers to firmly pull out the wire connector. It was too tight to remove with fingers. No damages.
Thank you very much! I don't use my printer often, but for the last few years, it's been printing dirty. I followed your steps here, and it's printing like new!
Geat video and explanation thanks. I had a transfer belt fault on a CLX-3305. Completly taking apart as per your second half of video and cleaning has solved the problem👍 the only different thing I did was fitting the side springs before the outer cover was reftted. Acess to them was then easier.
Excellent informative clear instructions. My printer had been fine until I needed to replace the black toner with a new one and the next print was awful quality with faded strips. Followed your instructions and felt very comfortable with my execution of the process but unfortunately made no difference to the faded bits. Could it be my new black toner cartridge?
Hi, this video has been most helpful. Upon cleaning the transfer belt, it has started to make very loud screeching noises when calibrating and printing. What can I do to solve this issue?
Thanks for the clip, very helpful, I replaced the transfer belt with a new one (Samsung) however the Status light continued to flash any ideas? Thanks again
This procedure will require going into the Tech menu to reset the counter for Transfer Belt (there are other UA-cam videos on how to do this depending on the model, but it essentially a specific sequence of key presses on the controls: the display will read Tech menu if you are successful. For the printer in this video without keypad, the sequence is Menu, Back, Left, Right, OK, Stop/Clear, Menu. The C460 with a keypad uses Menu, #, 1,9,3,4, Menu. Once in Tech Menu, then go to Data Setup, then Clear Count (for the specific part you have replaced)). The mainboard doesn't "know" that the Transfer Belt (or any other consumable part) has been changed: resetting the counter is the only way to tell it you have completed the procedure. If you get error messages on any of these other "Consumables" and/or the Status light continues red/message appears you need to reset any of these parts, the Tech Menu is the only way to do this after you change out the part. Important: only change out parts once you have pulled the plug. Hot-swapping parts with the unit powered on may create problems with locking in error messages and may damage the mainboard processor.
Hi great video. I have the same printer. I bought black toner but it is not original - they promissed it would be just as good as the original. Now I am not sure why the black color is weak when I print. Would it help to maintain the printer (maybe I did something wrong when I mounted the black cartridge) or is the problem that the toner is not original. It would be nice to know before I start maintainance. Thank you in advace. Hope the spelling is ok.
I think there is nothing wrong mounting the cartridge. Probably the toner cartridge is defective but the problem could be the drum unit too. The compatible cartridge are often good quality
CLP-315 with transfer belt not being wiped. I did clean it and disasembled just like in the video. The wiper has two rubber parts that do the wiping. The bigger one came loose when I tried cleaning it properly however. I cannot find a replacement part. Do I need a whole unit or will just the wiper fix my issues? It seems like the wiper does not take off all the powder left on the belt for some reason.
Great Video!! Thanks a lot - I just exchanged the transfer belt! My printer now is printing again :-) However - the note on the little display "prepare for ne transfer belt" is still there. How can I "delete" or stop this message ...
i can't get the transfer unit to stick back up in its original position, which makes it impossible for me to put the waste cartridge back. you make it look so easy. any suggestions?
hello, good afternoon, my printer marks the entire sheet with a very dark background, they told me that the problem could be the tape, if the tape is cleaned with alcohol and the blade, I will solve the problem or I have to buy the complete new tape, thanks .
hello, thanks for these, great videos! I have a question, I have a samsung 3305FN printer and it gives 2 errors: "replace ITB" and "replace fuser unit". I know there is a chip resetting method for drum unit by soldering in drum chip but I want to learn if there is a way to reset "ITB=image transfer belt" or "fuser unit" with some chip soldering or anything like that??
Great video. I'm sure the ITB for a Samsung CLP-315 isn't very different. Does the belt itself ever wear out? The symptom is a blurry line maybe 6-10 mm wide across that page--sometimes yellow toner, sometimes black. Samsung literature says to replace the belt assembly. Is the real problem likely to be the wiper blade, or that the belt itself is worn out?
Grazie, Signore Viandant. I've found that replacement ITB assemblies cost $US 65-$US 130. But replacement belts are $US 18-$US 20 from China and I now have one. I have a spare ITB assembly I can play with. I had one question, but now I have two: 1) Can I disassemble the assembly to the degree necessary to replace the belt? The Samsung repair manual suggest that this can only be done at the factory where special jigs are used. 2) Do you think that the wiper blade has worn in such a way as to damage the belt and would shorten the life of a new belt? Or perhaps that it's normal belt wear? (I realize that without seeing the blade both of us are just guessing.) I think I might go back to the China websites and see if the wiper blade is available. I love the CLP-315 and have used and used it. We also have a CLX-3175 (all-in-one). I have performed the special mods on both of these as described here: rumburg.org/printerhack/ . Don't try this on anything but a CLP-310 or 315 or CLX-3175. It takes advantage of a quirk in the firmware which was removed in later versions.
Hi, thanks for your informative video. I bought a new transfer belt and fitted it as per your instructions which went well. But, when I turned the printer back on the error message "prepare new transfer belt" still came on. Any suggestions? Thanks.
After replacing the unit, you still need to reset the counter of the printer, which is done in the Tech Setup. To enter it, the combination of keys varies depending on the printer model - and unfortunately, Samsung didn't make them public (but they can be found for some models around the internet and on YT).
I figured it out - I missed replacing the screw that holds the black flat plastic part at the end near the wires. After installing the screw (which I now call the colour screw) the printer works perfectly - no more ghost images and bright colours. Thanks again for the video it was excellent!
I just replace the drum unit, a new cartridges toner, and the lights still blinking, all of them. I was wondering if you could get some solution to this problem. Thank you
There are no reset procedures. I think the problem are the chip. Are compatible cartridges? However Samsung make all they can to create problems to cartridges, even original ones
@@viandant5 the cartridges are compatible but not original and the image drum unit chip was already replaced. Could it be the transfer belt? Many thanks
Hello, thanks for the video, I followed the cleaning instructions, but I still have a problem, when sending more than 2 sheets of some document, I get a ghost print of the watermark of the previous sheet, when I disassemble the transfer cartridge I notice that has remains of toner with the previous printing on it, apparently it is not discarding them, any solution? greetings from Mexico
Hola Bernardo! has conseguido resolver el problema que mencionas? Me trajeron una impresora que hace exactamente lo que mencionas, un "fantasma" de la impresión, pero sólamente es en la siguiente página. y no existe un segundo fantasma...
@@victoraguilars.4281 hola, no pude resolverlo ya que no consegui otra unidad de transferencia para probar, lo que hace mi cliente es mandar a imprimir una hoja por una, y asi casi no sale el fantasma ya que el repuesto es costoso, va a esperar a que se le termine el toner para desechar el equipo.
The right plastic lever shown you opening from the minute 1:18 was suddenly fell down of my printer, I tried to return it back but couldn't know how, any help?
have a problem with my Samsung clp-365w. On power up it doesn't go through its usual warm up procedures. It is connected to the computer via usb. Removing the usb cable causes the conputer to sound so it knows it is disconnected from the computer. I think it is a hard wear problem with the printer itself. I have recently emptied the wast container. I worked after that but one morning after I powered up the printer all lights on the display came on steady and the printer didnt go through its usual warm up proceedures.
mi impresora samsung c460w no imprime a color y si tiene toner, se le cambio la cinta de transferencia porque manchaba mucho, ahora imprime pero no quiere a color, que puedo hacer?
II think it's not an electonic problem to the main board, you should have an error message. It could be a mechanical problem, a gear or something not in the right position
![АЛАУДИНОВ у Скабеевой: эти их ВСУ нас НЕ ДОГОНЯТ 😁 [Пародия]](http://i.ytimg.com/vi/an0anqU4WGQ/mqdefault.jpg)
Top, hab nach einem anderen Video nur das mit der Alufolie gemacht, was nichts gebracht hat. Aber der Hinweis mit den Zählerständen zurücksetzen war GOLD WERT!!!!!! DANKE
This is the best tutorial ever! Samsung should pay you for this
Thank you so very much. You saved me time and money. People like you are the reason good moral values are still in place
this video is the only one giving precisely the steps. Thanks a lot
I was having difficulty removing the transfer belt & decided to go online for help. Thanks for this video
A+ video! For anyone with trouble removing the wire clip: I had to use pliers to firmly pull out the wire connector. It was too tight to remove with fingers. No damages.
Exact same setup as my C430W. Thank you for taking the time to make and share this.
Thank you very much! I don't use my printer often, but for the last few years, it's been printing dirty. I followed your steps here, and it's printing like new!
Your video helped me detect why my transfer belt wasn't printing properly. Thank you.
happy to help you!
Lots of fellow print-users praise Your video, today I join the congritation of happy print-users with a fixed and working transfer belt !!
I have different model, but the basic principle is the same. Thanx for saving me buying new printer! Merry Christmas!
Geat video and explanation thanks. I had a transfer belt fault on a CLX-3305. Completly taking apart as per your second half of video and cleaning has solved the problem👍 the only different thing I did was fitting the side springs before the outer cover was reftted. Acess to them was then easier.
Thanks for this video 👍 You did an awesome job explaining step by step. I fixed my printer myself following the instructions and it works again.
That was the solution for my big problem about the yellow lines on the C460W- Great....Thank yu
Finally I did make it. Thank you so much! I just used a qtip (cotton) in order to entirely clean the residue container.
Thanks so much for this. I was on the point of throwing out this printer for
Thanks, guy! You saved me a lot of tears.
I thought I fixed my problem yesterday but I printed something this morning & my printing is still smudging. I'm going to try cleaning the drum today
Just saved me from buying a new printer. Thank you!
your instruction helped me a lot. Thank you.
Verstehe zwar kein englisch, muss ich bei diesem sehr gut erklärten Video auch nicht. Herzlichen Dank
There are the german subtitles
Great tutorial
Thanks a lot! Very detailed video and nice breakdown of steps!
Thanks a lot dear Viandant ! Very clear & detailed video
Excellent informative clear instructions. My printer had been fine until I needed to replace the black toner with a new one and the next print was awful quality with faded strips. Followed your instructions and felt very comfortable with my execution of the process but unfortunately made no difference to the faded bits. Could it be my new black toner cartridge?
Probably the cartridge is defective. The low quality is on all colors?
Thank you so much. Your video helped save our problem
Thank you for the video! It was interesting, this model has not yet analyzed the transfer belt!
Best reguards from Kiev
+vovanfun thank you, have a nice day
Very useful video. Solves many problems.
solved my problem !! Thanks to you, my printer's working again. Awesome, keep it up!
Super erklärt. Und bei meinem Drucker hats funktioniert. Danke
Muchas gracias me ayudo mucho tu video.
😎 SUUUUUPER- Thanks so much
thanks, had to clean the transferbelt because there was some dirt on it causing white dots on black images :)
MERCI pour cette superbe vidéo !
Muchas gracias por mostrar tu meticuloso trabajo!!
Hi, this video has been most helpful. Upon cleaning the transfer belt, it has started to make very loud screeching noises when calibrating and printing. What can I do to solve this issue?
I the unit has been correctly assembled, I think you have to lubrificate the cleaning blade of the belt, or wait until the loud disappear
Great Tutorial, well done and thank you very much.
Interesting and useful! How can you know how much toner is left in each cartridge? thanks
The toner level? You can print the printer status ua-cam.com/video/RqY9Z7bJJcE/v-deo.html
Good Boy, i love you for this Video 😙
Excelente video... muy ilustrativo. Muchas gracias
Thanks for the informative video, fellow human.
Great video, thanks👌
no hablo ingles pero estoy totalmente agradecida por su ayuda
There are spanish subtitles
Very useful video, my printer prints clean once more. Thx!
Thanks for the clip, very helpful, I replaced the transfer belt with a new one (Samsung) however the Status light continued to flash any ideas? Thanks again
I've no idea, the transfer belt counter shuld be resetted.
This procedure will require going into the Tech menu to reset the counter for Transfer Belt (there are other UA-cam videos on how to do this depending on the model, but it essentially a specific sequence of key presses on the controls: the display will read Tech menu if you are successful. For the printer in this video without keypad, the sequence is Menu, Back, Left, Right, OK, Stop/Clear, Menu. The C460 with a keypad uses Menu, #, 1,9,3,4, Menu. Once in Tech Menu, then go to Data Setup, then Clear Count (for the specific part you have replaced)). The mainboard doesn't "know" that the Transfer Belt (or any other consumable part) has been changed: resetting the counter is the only way to tell it you have completed the procedure. If you get error messages on any of these other "Consumables" and/or the Status light continues red/message appears you need to reset any of these parts, the Tech Menu is the only way to do this after you change out the part. Important: only change out parts once you have pulled the plug. Hot-swapping parts with the unit powered on may create problems with locking in error messages and may damage the mainboard processor.
Hi great video. I have the same printer. I bought black toner but it is not original - they promissed it would be just as good as the original. Now I am not sure why the black color is weak when I print. Would it help to maintain the printer (maybe I did something wrong when I mounted the black cartridge) or is the problem that the toner is not original. It would be nice to know before I start maintainance. Thank you in advace. Hope the spelling is ok.
I think there is nothing wrong mounting the cartridge. Probably the toner cartridge is defective but the problem could be the drum unit too. The compatible cartridge are often good quality
Very good video
Tausend Dank für dieses Video!!! Echt super gemacht 😍
Great instructions. Is there a replacement blade available?
may be on alibaba
@@viandant5 OH, thank you I didn't think about them.
Bravo ça marche. J'ai pu tout nettoyer 👍👌
CLP-315 with transfer belt not being wiped. I did clean it and disasembled just like in the video. The wiper has two rubber parts that do the wiping. The bigger one came loose when I tried cleaning it properly however. I cannot find a replacement part. Do I need a whole unit or will just the wiper fix my issues? It seems like the wiper does not take off all the powder left on the belt for some reason.
I think it's difficult to find the wiper blade. May be on aliexpress
Great Video!! Thanks a lot - I just exchanged the transfer belt!
My printer now is printing again :-)
However - the note on the little display "prepare for ne transfer belt" is still there.
How can I "delete" or stop this message ...
I don't know any reset method, it should delete itself with the new belt
Gracias por compartir.
Thks . it was very usefull for a 3170. it almost the same. now the printing are perfect.
Excellent video! Thank you so very much!
Thanks a lot, Big help. When I need to made urgent print at wekend and my printer it does´nt work .
THANK VERY MUCH
Thanks for your help... It was very nice...
You helped me big time friend
THANKS FOR HELP ! :-)
thank you so much!
i can't get the transfer unit to stick back up in its original position, which makes it impossible for me to put the waste cartridge back. you make it look so easy. any suggestions?
there are no tricks, it should go into position without too much problems
Should I still follow this video to try sort out the problem x
I’m having problems with paper jams using glossy vinyl paper. Will this help if I clean that part?
No, probably the problem are the feed rollers, or the fusers
hello, good afternoon, my printer marks the entire sheet with a very dark background, they told me that the problem could be the tape, if the tape is cleaned with alcohol and the blade, I will solve the problem or I have to buy the complete new tape, thanks .
Which tape? the belt? Yes you can try to clean it with isopropyl alcohol
Merci !
hello, thanks for these, great videos! I have a question, I have a samsung 3305FN printer and it gives 2 errors: "replace ITB" and "replace fuser unit". I know there is a chip resetting method for drum unit by soldering in drum chip but I want to learn if there is a way to reset "ITB=image transfer belt" or "fuser unit" with some chip soldering or anything like that??
Thank you, I regret but I don't know any reset method for fuser or ITB
the reset chip is only for the toner/dv unit
Excellent!
you sir are a hero!
VERY helpful!!! Thanks!
Hi, do you have a video showing how to change the Fuser in a samsung Xpress C480FW please?
it's similar to samsung clp 320/360, in this channel there is a video
thanks, i fix it
THX 🙂
Great video. I'm sure the ITB for a Samsung CLP-315 isn't very different. Does the belt itself ever wear out? The symptom is a blurry line maybe 6-10 mm wide across that page--sometimes yellow toner, sometimes black. Samsung literature says to replace the belt assembly. Is the real problem likely to be the wiper blade, or that the belt itself is worn out?
probably the belt itself is worn, and the wiper blade is one of the causes
Grazie, Signore Viandant.
I've found that replacement ITB assemblies cost $US 65-$US 130. But replacement belts are $US 18-$US 20 from China and I now have one. I have a spare ITB assembly I can play with. I had one question, but now I have two:
1) Can I disassemble the assembly to the degree necessary to replace the belt? The Samsung repair manual suggest that this can only be done at the factory where special jigs are used.
2) Do you think that the wiper blade has worn in such a way as to damage the belt and would shorten the life of a new belt? Or perhaps that it's normal belt wear? (I realize that without seeing the blade both of us are just guessing.) I think I might go back to the China websites and see if the wiper blade is available.
I love the CLP-315 and have used and used it. We also have a CLX-3175 (all-in-one). I have performed the special mods on both of these as described here: rumburg.org/printerhack/ . Don't try this on anything but a CLP-310 or 315 or CLX-3175. It takes advantage of a quirk in the firmware which was removed in later versions.
I've have a video on how to disassemble the belt. I think the wiper blade is ok.
I think that hack will work only if you do not have a new firmare version.
It seems to work on all CLP-315 and CLX-3175. It will BRICK any newer models. This is why I keep maintaining my old ones.
thanks very mutch , شكرا جزيلا
Hi, thanks for your informative video. I bought a new transfer belt and fitted it as per your instructions which went well. But, when I turned the printer back on the error message "prepare new transfer belt" still came on. Any suggestions? Thanks.
After replacing the unit, you still need to reset the counter of the printer, which is done in the Tech Setup. To enter it, the combination of keys varies depending on the printer model - and unfortunately, Samsung didn't make them public (but they can be found for some models around the internet and on YT).
@@MrSuicycle It's usually 1934 for most models
I performed the cleaning process, but the printer won't print colour anymore - just black and white - any suggestions?
a cleaning process in a CLP-365? I think it's a problem of settings
I figured it out - I missed replacing the screw that holds the black flat plastic part at the end near the wires. After installing the screw (which I now call the colour screw) the printer works perfectly - no more ghost images and bright colours. Thanks again for the video it was excellent!
Thanks for this video. i have managed to repair my printer
How often do you need to clean the transfer belt? once every 10,000 pages or so?
Not necessary to clean it often. MAy be 30-40.000 pages if there are no print quality problems
excellent...thanks man!!!!
I just replace the drum unit, a new cartridges toner, and the lights still blinking, all of them. I was wondering if you could get some solution to this problem. Thank you
There are no reset procedures. I think the problem are the chip. Are compatible cartridges? However Samsung make all they can to create problems to cartridges, even original ones
@@viandant5 the cartridges are compatible but not original and the image drum unit chip was already replaced. Could it be the transfer belt? Many thanks
@@marcelolobfig Yes, it could be the transfer belt. Check the printer folder to have more informations
Hello, thanks for the video, I followed the cleaning instructions, but I still have a problem, when sending more than 2 sheets of some document, I get a ghost print of the watermark of the previous sheet, when I disassemble the transfer cartridge I notice that has remains of toner with the previous printing on it, apparently it is not discarding them, any solution?
greetings from Mexico
Are you sure the problem is the transfer belt? It could be caused by the drum too and by the fuser rollers
Hola Bernardo! has conseguido resolver el problema que mencionas? Me trajeron una impresora que hace exactamente lo que mencionas, un "fantasma" de la impresión, pero sólamente es en la siguiente página. y no existe un segundo fantasma...
@@victoraguilars.4281 hola, no pude resolverlo ya que no consegui otra unidad de transferencia para probar, lo que hace mi cliente es mandar a imprimir una hoja por una, y asi casi no sale el fantasma ya que el repuesto es costoso, va a esperar a que se le termine el toner para desechar el equipo.
красава! всё аккуратно чётко!
No sabia que allan x el mundo tambien repara impresoras!!!
ขอบคุณครับ=thank you
감사합니다 꾸벅~
Very well thank you.
hi, i have do this deep cleaning but after doing that my printer print only in grayscale. I dont understand why?
You have any idea?
What is a deep cleaning? Check the printer settings in the printer folder, may be it's set in "Grayscale"
The right plastic lever shown you opening from the minute 1:18 was suddenly fell down of my printer, I tried to return it back but couldn't know how, any help?
probably it's broken, try to reassemble the printer without that lever
have a problem with my Samsung clp-365w. On power up it doesn't go through its usual warm up procedures. It is connected to the computer via usb. Removing the usb cable causes the conputer to sound so it knows it is disconnected from the computer. I think it is a hard wear problem with the printer itself. I have recently emptied the wast container. I worked after that but one morning after I powered up the printer all lights on the display came on steady and the printer didnt go through its usual warm up proceedures.
the waste toner container has a fuse, it needs to be reset
viandant5 how do you reset the fuse. I have tried cleaning the waste container
I do not know any reset method
Can I use hydrogen peroxide to clean it as a substitute?
No, better the normal alcohol
Nice video.
Thank you!!!
Hello, i have a clp 315 and i cant remove the drum unit, seems like its stuck?
Yes, it could happen i's hard to remove. Try to move it up using a lever or a screwdriver then pull it out
How do I find out what error my printer has ? Because it is flashing red and not printing I don't know why
I couldnt make it. Perhaps, it was very dirty. I did everything you mention on the video and no. :(
Hallo, vielen Dank für das Video. Nach der Reinigung des Transfer Belt druckt der C480FW nur noch schwarz / weiss. Wo liegt der Fehler? Vielen Dank
Ich denke, das Problem sind die Druckereinstellungen
Também estou com este problema e não é a configuração 😭
I have an error door open when all the doors of the printer is closed. it also says PAPER PROBLEM
If all the doors are open it's normal to have a printer error
mi impresora samsung c460w no imprime a color y si tiene toner, se le cambio la cinta de transferencia porque manchaba mucho, ahora imprime pero no quiere a color, que puedo hacer?
es decir, ¿imprime en negro lo que debería imprimirse en color?
das hat mir geholfen !
What is the problem when the pick up roller won't engage? It won't turn.
II think it's not an electonic problem to the main board, you should have an error message. It could be a mechanical problem, a gear or something not in the right position