Sewing Machine Bobbin Winder Fix - Elna Air Electronic
Вставка
- Опубліковано 21 лип 2024
- The bobbin winder is not working on this Elna Air Electronic sewing machine.
There are several reasons why a sewing machine bobbin winder may not be functioning as it should.
In this video I go through some of the scenarios in troubleshooting a bobbin winder issue.
This applies to many types of sewing machine with this type of winder but here I am showing specifically the Elna Air Electronic SU.
Other very similar models include all other air electronic models such as the TSP, SP etc.
Index:
0:00 - Introduction
0:56 - Explaining some of the reasons a bobbin winder may not work
3:20 - The likely issue is identified
3:28 - Removing the lid (and handle if required)
5:30 - A look at the problem
6:32 - Fitting a new rubber ring to the bobbin winder
7:11 - Removing a badly worn ring
7:50 - Cleaning any residual oil and grime
9:37 - Reinstalling the lid and handle (if removed)
11:09 - Testing the bobbin winder
13:17 - Conclusion
My web site - www.institches.co.nz
If you'd like to support my channel, please visit - www.patreon.com/sewingmachines - Навчання та стиль
Such a lovely machine, I have two of them. Re the bobbin winding, I always put the curved handle of my small scissors on top of the thread spool I am using to fill the bobbin and nudge the thread filling the bobbin so it winds evenly. And have a felt circle under the spool to hold and minimise the jerking.
Great video. Always great to watch to get ideas if things go wrong with a machine.
What if the bobbin winder is seized up?
Got the same model, trying to fix my winding, hope it will work!
Thanks I think I know my problem now
I have a Elna 3003, but still don't how wind a bobbin.
It seems too confusing to get started.
I have a uniform to repair!
Love the kitty cat😻
Hi. What do u call the black circle thing u put on? Rubber rang?
I have the exact machine. I’m looking for help as I removed the clutch and now can’t get the machine to work. It will engage if I turn it by hand but when I try to tighten the clutch the hand wheel wont turn?
I have to try this with my old Brother machine It quit mid bobbin fill today. I just found the rubber rings on Amazon.
Great
My Janome New Home winder wheel came off. None of these show the winders that are like that machine.
I press the pedal of the machine but nothing moves. may be the air ways have to be cleaned?
Hello, thank you for doing such an informative video. I was able to isolate the problem with the bobbin winder on the vintage Nelco machine I just inherited. It appears the bobbin winder shaft itself is sized. It will not spin at all. I have tried oil on it, PB blaster and WD 40 trying to work it into any area. Is there anything else to try on a siezed shaft ?
Thanks. Maybe try a little heat. Be careful not to melt anything though. Not too much heat.
Hi there, thanks a lot for your video! It was very clear and helpful. Now, I ran into a different problem. I dissembled the bobbin case, actually I dettached the black plastic ring that goes below, and I don't seem to be able to put it back together. I must be doing something wrong because once I screw it back to the bobbin case, it doesn't fit in the bobbin case hole anymore. Any ideas? Thanks a million beforehand!
Hi, separate the black ring and locate it in place in the machine. Then place the bobbin case over it in place and tighten the screws. I hope that helps. Thanks.
That thread holder on the top, mime broke off...do you think I can use almost anything for a replacement, like a long screw or stick?
As a temporary measure that would probably do. Just make sure whatever you use doesn't fall down the hole. Thanks.
I accidentally dropped my Elna a couple of weeks ago. Everything works fine now except the bobbin winder. I watched this video and opened the top and a V shaped spring came off near the winder. How do I put that back on. BTW Thanks you for such an awesome video!
Glad it helped!
Interesting video. I have a vintage Necchi Esperia and when I disengage the needle to wind bobbin the needle still goes up and down. How can that be fixed?
Sounds like the hand wheel may be binding on the top shaft. Try lubricating it. Thanks.
Tried, didn't work. Thanks anyway.
Hi I looking foot pedal and wire power .I m in Namibia pls
I have an identical machine, I can't change the sewing styles, I just bought it and I don't know how to use it, you can review it.
I've done a video on that. You can find it here - ua-cam.com/video/vPbWPNXlu8M/v-deo.html Thanks.
In español ,please !!!!!
1. Blow out all the cotton/dust crud with compressed air - working on a dirty machine is a big No-No..
2. Wipe the old rubber crud off the handwheel inner part with 75%+ ALCOHOL. A simple dry rag doesn't cut it, and the old rubber pasty bits mixed in to the new rubber ring = shortened lifetime.
3. Oil the shaft of the bobbin winder before replacing the rubber ring.
Other than that, very nice video.
Oh yes, totally agree with most of your points but if I had to explain the obvious in all of my videos, every time, they would be even longer than they are now.
As always, blowing out and cleaning a machine is part of a full service.
As you could see in the video, the handwheel was very clean without having to resort to using IPA. Some of these videos are designed to help people who may not have access to compressed air or other specialised tools and equipment.
I just show the fix to get the machine up and running. Professional servicing is always recommended but sometimes people just want to get their machines going in the meantime.
Thanks.