Some tips: 1.use thread locker especially for the big hub bolts. You'll probably get crunches if you don't! 2.For the controller & battery gaskets: you can clean them with soapy water ( very lil soap) and recondition them with some vaseline. if you decide to cut them, probably super glue will work to glue the ends. Do it before applying Vaseline. 3. Using a lil Vaseline or dielectric grease around the motor connectors and footpad connector will help keeping water & moisture out.( apply with the finger around the female connectors) 4.if your pint has a metal nut holding the power button. Get rid of it. Will mess things up if hasn't already.
@@texanallday Most likely YES! try if the bolts are loose: try tightening them, if they tighten relatively easy = they are loose. Not a good idea to test them by unscrewing them.
@@Julian3vil yes you are right, but i think 1hour in the freezer is not a big thing for the gasket. My gasket was very flexible after i put it out of the freezer. After the freezer i connected it to the box with super glue
Every morning I wake up and wonder first; ‘is it 84v battery time from tony’? And then I wonder ‘is it baby core time from tony’? My dude, it’s gonna be a long winter! Really hoping the 84v will surprise us sooner than Q2 so I can have it installed when spring comes! Gonna tie me over until the Tony Pint answer! So excited!!! 🙌🙌🙌
@@vaeyano I have the stock pint X battery. I haven't really tested the range with the pint XV, I have really tested it with my GT-V. If you are the same weight as a rider with a stock GT and go the same speed, your range should be about the same. But the V kits allow you to go harder on the board. When I go trail riding with my buddies I usually have about 15% less battery but it's so fun to blast past them on every hill. These V kits will also let your motor heat up faster than stock.
Hey Tony - will you be making your own battery box housing for the 84v battery you mentioned on the website? Or just the battery and it should fit in the regular pint housing?🙏🙏🙏
Some years ago I bought a Quart battery upgrade form Chibatterysystems(for the original pint), any idea if it's compatible with the PntV upgrade? Thinking about the fit since the battery is a bit bulkier and I remeber I had to cut off some plastics from the bms cover. But non the less looks awesome man!
@@Kay0Botthis really isn’t accurate and makes no sense to me. As the XR’s get “older” and more abused they get cheaper and more accessible to people. OneWheels are fucking expensive. If it wasn’t for affirm financing I wouldn’t own my Pint, PintX, or GT. I had wait MONTHS to score my used XR for $700 and was disappointed to see how everything is being discontinued for it. To this day owning Four onewheels, the XR is by far the best. Lighter and smaller than the GT and Larger and more comfortable to ride than my pints. Fingers crossed for a GT Compact/Slim/Lite from Future Motion. GT-S or Rally didn’t appeal to me because I already don’t want to lug my GT around.
@wishdrftr xr no longer in production. So no more are being made. Therefore, the stock of xr is finite. XRs are lost due to damage/neglect. Some are converted to vesc using other paths. These are what tony has to consider when deciding how many xr coversion kits to make.
@@Kay0Bot He'll sell a literal ton of XRV's when he releases it. There's a gazillion XRs out there, mostly ridden by die-hards who can't wait to VESC it and eventually put in bigger packs.
"Thank you for providing outputs that allow to upgrade the Pint! I have a Pint with the 'rewheel' software and an additional GT mod battery. Does the kit work? Should I plan for a new VNR plug?"
Are some of these kits shipped out without the plastic thermal pad cover? I was able to dig my thumb into the pad and mark it up, couldn't find a cover
@@FloatTheNorth look extra close in the ESD bubble wrap packages, it blends in really well. If you really didn't get it, email Tony and he will send one out.
Tony, I am Korean. Please understand that I am using Google Translator. I wonder if, except for the United States where there is a lawsuit, it is not possible to sell it as a general payment other than coins in other countries.
@@floatwheel I see, thank you. I want to purchase with a credit card, but it is not possible to purchase coins with a credit card in Korea. That's why I asked the question. I’m enjoying the video, Tony!
Small question: the part of the controller top plate that is being removed, isn't it a stiffener ? The footpad of the pint are plastic if I'm not mistaken, by removing the stiffener, no risk to simply break the lid ?
Some tips:
1.use thread locker especially for the big hub bolts. You'll probably get crunches if you don't!
2.For the controller & battery gaskets: you can clean them with soapy water ( very lil soap) and recondition them with some vaseline. if you decide to cut them, probably super glue will work to glue the ends. Do it before applying Vaseline.
3. Using a lil Vaseline or dielectric grease around the motor connectors and footpad connector will help keeping water & moisture out.( apply with the finger around the female connectors)
4.if your pint has a metal nut holding the power button. Get rid of it. Will mess things up if hasn't already.
You can put the gaskets also in the freezer. It will fit better after that
@@Cptnfloat I'm not sure that is a good idea. I know extreme cold is not good for rubber and u want rubber to be soft and flexible.
@julian3vil what do you mean crunches if we don't use threadlocker? Is that the noise emanating from my pintV after changing tire?
@@texanallday Most likely YES! try if the bolts are loose: try tightening them, if they tighten relatively easy = they are loose. Not a good idea to test them by unscrewing them.
@@Julian3vil yes you are right, but i think 1hour in the freezer is not a big thing for the gasket. My gasket was very flexible after i put it out of the freezer. After the freezer i connected it to the box with super glue
I don’t even have a pint I just like watching tonys videos
Tell me about it. I have the GTV kit and my board is unleashed. VESC is the future of this sport.
One of the best~!~and I love Jeff's, but damn Tony, can't wait to see what you do for our XR's...
Every morning I wake up and wonder first; ‘is it 84v battery time from tony’? And then I wonder ‘is it baby core time from tony’?
My dude, it’s gonna be a long winter!
Really hoping the 84v will surprise us sooner than Q2 so I can have it installed when spring comes! Gonna tie me over until the Tony Pint answer!
So excited!!! 🙌🙌🙌
I got my kit installed yesterday and Holy Moly the Pint is super fun now. I can't believe how much power the Pint has. Great Job Tony!!
It runs vesc on the controller right?
Yes, it does. The FM onewheel app is no longer used.
@@hasone1848after install what's the setup like to use another app then?
What about the range and battery? did you upgrade your battery too?
@@vaeyano I have the stock pint X battery. I haven't really tested the range with the pint XV, I have really tested it with my GT-V. If you are the same weight as a rider with a stock GT and go the same speed, your range should be about the same. But the V kits allow you to go harder on the board. When I go trail riding with my buddies I usually have about 15% less battery but it's so fun to blast past them on every hill. These V kits will also let your motor heat up faster than stock.
well done Tony! Another great product to live in future motions heads rent free. Bring on the floatwheel v2!!!
Tony you should put the controller inside the cannon core then make a pint size onewheel.... This would be the ultimate board ❤️❤️❤️
LEGENDDDD!!! We love you Tony.
Thanks for all the hard work you are doing for this community and sport. Your products are amazing.
Keep putting out great products and we'll keep buying them!
Love your work Tony and team. Looking forward to upgrading my 2 PintX boards when I upgrade my 2 ADV to version 2 controllers.
Nice clear instructions. Looking forward to the XRV kit
Its so cool what you are doing. Good job Tony!
Hey Tony - will you be making your own battery box housing for the 84v battery you mentioned on the website? Or just the battery and it should fit in the regular pint housing?🙏🙏🙏
It's here!!!! I'll be installing mine later. Thank you Tony
Installed - now to ride!!
Amazing upgrade ! 🥰👌🏼
Thank you guys !!!!
Mine arrived today! THANKS TONY
Some years ago I bought a Quart battery upgrade form Chibatterysystems(for the original pint), any idea if it's compatible with the PntV upgrade? Thinking about the fit since the battery is a bit bulkier and I remeber I had to cut off some plastics from the bms cover. But non the less looks awesome man!
Is there any way you can upload the GTV install video on your website since the youtube video was taken down?
Tony! Please make XRV for us peasants. I promise to buy one!
I will also buy one !!
I think he will but very limited run. Since no more new xrs are being made by futuremotion, hence less and less xr riders will need modding
@@Kay0Botthis really isn’t accurate and makes no sense to me. As the XR’s get “older” and more abused they get cheaper and more accessible to people. OneWheels are fucking expensive. If it wasn’t for affirm financing I wouldn’t own my Pint, PintX, or GT. I had wait MONTHS to score my used XR for $700 and was disappointed to see how everything is being discontinued for it.
To this day owning Four onewheels, the XR is by far the best. Lighter and smaller than the GT and Larger and more comfortable to ride than my pints.
Fingers crossed for a GT Compact/Slim/Lite from Future Motion. GT-S or Rally didn’t appeal to me because I already don’t want to lug my GT around.
@wishdrftr xr no longer in production. So no more are being made. Therefore, the stock of xr is finite. XRs are lost due to damage/neglect. Some are converted to vesc using other paths.
These are what tony has to consider when deciding how many xr coversion kits to make.
@@Kay0Bot He'll sell a literal ton of XRV's when he releases it. There's a gazillion XRs out there, mostly ridden by die-hards who can't wait to VESC it and eventually put in bigger packs.
"Thank you for providing outputs that allow to upgrade the Pint!
I have a Pint with the 'rewheel' software and an additional GT mod battery. Does the kit work? Should I plan for a new VNR plug?"
Great video, do you use the FM app with this kit or is there a Floatwheel one.
XRV kit tho? possibly 18 20s for it too?
Sweet I'm preordering today!
any update on xrv?
Least supported product gets the least love - futuremotion
Are some of these kits shipped out without the plastic thermal pad cover? I was able to dig my thumb into the pad and mark it up, couldn't find a cover
Pre ordered for my Pintx 🤟
where? I thought the site was down
@@3tch3r floatwheels ru
@@3tch3r new site has been up for a bit now
What about creating a 4 point shock system since FM is hoarding the patent on that? Id by them for sure!
How bright are the replacement headlights and taillights? The original lights are super dim, are the new ones substantially brighter than those?
@@isaacgraham3684 way better than og ones
Anyway to get an update on the videos?
Hi Tony!
Any news about the gen 2?
I am torn between ordering now a float wheel and upgrading later or waiting for the new gen
What is your advice? 😂
Does this mean any battery can work with this BMS?
Will the pcbs be available separately too? The bms as an option would be nice
Would it work if my PintX is currently giving me an error message? (Lightbar flashing yellow)
do we have to program the board at all for pushback or top speed or can you just install and go?
@@kody7041 install and go
@@floatwheel with the supplied bms does it work with the oem battery because the oem battery has reverse polarity if im correct
Nice work guys
@Tony any eta yet on GTS-V? Can't wait to try 113v vesc and slap a n52 655 on it.
that board will be beefy if you do that!
Tony, love you guys! Any eta on adv v2 electronics? Thank you
Ah v2 bms, gimme another month or so, had to rewrite everything on the bms Because we switched to a low consumption MCU.
@@floatwheel will you be selling BMS and pint& XR connectors alone?
Can’t wait to buy
Bring back the funny cat carpet!
It's the same for the Pint and Pint X is the same kit right?
@@brandonaskins7969 yep same kit
@@floatwheel can't wait for my kit. I'll have the ADV, GTV, and PXV. Thanks for making FMs products better by fixing their electronics. 🫡
What app (android) can i use for making config & profile changes?
Can we find a way to watch all your old uploads that are gone. The video on setting up the floatwheel is important to alot of people
@surfdado released up to date setup video. I highly recommend to use that for setup over any other. 😉
"Configurable haptic buzz and pushback"
Wow thats awesome! CPeeSC get wrecked.
This is awesome
What firmware is preinstalled?
I am saving up money for this, I have a pint x and want one so bad😩
Oh man, what a bummer with the same charging plug connector in the BMS 😕
@@raulhariasl there's a second abundant green port if you have your original port burnt, it's just there so people can plug n play
With stock pint battery how many miles can you get on this?
Stock range
Thank you!!!!!
Super cool
Legend
Tony, 想再問多一次可否用微信支付給你們？和寄到香港？另外我沒有用過其他app 去設定pint, 這個是不是已經設定好？自己也可以修改？ 我要訂2套呀。謝謝你.
無法用微信支付，如果你能來台灣
我可以幫你搞定🤝 lol
yes!!!
ADV 2 ETA??
Se ve un poco difícil pero seguro lo haré 😅
🙌
My kit arrived with no Rad plate 😢 - now i cannot finish my upgrade, pretty sure this needs heat dissipation...
Same...
Mine as well, solution?
@@FloatTheNorth look extra close in the ESD bubble wrap packages, it blends in really well.
If you really didn't get it, email Tony and he will send one out.
Tony, I am Korean. Please understand that I am using Google Translator. I wonder if, except for the United States where there is a lawsuit, it is not possible to sell it as a general payment other than coins in other countries.
using usdc is easier for us to operate worldwide
@@floatwheel
I see, thank you. I want to purchase with a credit card, but it is not possible to purchase coins with a credit card in Korea. That's why I asked the question. I’m enjoying the video, Tony!
@@동모형ur friend from Taiwan. Maybe can help you.
Small question: the part of the controller top plate that is being removed, isn't it a stiffener ?
The footpad of the pint are plastic if I'm not mistaken, by removing the stiffener, no risk to simply break the lid ?
Kinda wishing I had not sold my Pint.
But Tony said he would make the OG pint a beast :/ why sell it 😢
@@alibabarouge Life happens
Does this work woth the quart battery?
@@turdburdexpress yup
I feel like I would f this up badly
Take a photo of every step of the unscrewing/removal process so you can look back for reference when putting them all back together again.
you will be fine take your time don't get frustrated take a break do something else if u get frustrated and make sure to use blue loctite
I need this kit for my Pint