7.3 POWERSTROKE COMMON AND RARE OIL LEAKS IN VALLEY...........
Вставка
- Опубліковано 15 кві 2022
- STOP TODAY TO SEE VALLEY OIL LEAK LOCATIONS IN THE 7.3 POWERSTROKE AND SOME YOU MAY NOT BE AWARE OF....................
DIRECT PRODUCT LINKS BELOW
Garrett Powermax GTP38R Ballbearing Turbocharger for Powerstroke 7.3L
amzn.to/3ruUXLK
1994-2003 Ford 7.3L Powerstroke Diesel Turbo Pedestal Yellow O-Ring Gaskets OEM
amzn.to/3Ev1CL1
Garrett Turbo Pedestal Non EBP Valve 99.5-03 Ford Powerstroke 7.3L
amzn.to/3MgIEup
Wicked Seals HPOP Oring Kit Compatible with Ford 7.3L Powerstroke Diesel 1994-2003 High Pressure Oil Pump seal set Like AP0011
amzn.to/3KW6TOi
Ford 2C3Z-9G804-AB High Pressure Oil Pump O-Ring Seal Kit
amzn.to/3MdEnrC
IPR Valve Seal Kit for 1994 - 2003 7.3L Ford and International
amzn.to/3jOKXZf
PIILOO High Pressure Oil Pump HPOP Master Service Kit with O-Ring Seals & Base Gasket Compatible with Ford Powerstroke 7.3L 1994-2003 and Navistar DT466 & T444E 1995-2004
amzn.to/37XZKya
Dorman 635-128 Oil Reservoir Gasket Compatible with Select Ford / IC Corporation / International Models
amzn.to/3jLxa5Z
Dorman 635-5002 Engine Timing Cover Compatible with Select IC Corporation / International Models
amzn.to/3voYBrA
#customworks
#7.3powerstroke
#oilleak
#powerstroke
#valleyoilleak
#sensor
#whitesmoke
#idle
#losspower
#vgg
#scotty
Copyright Disclaimer. Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.All info presented is for humor no real effort went into actually checking correct or facts . - Авто та транспорт
your videos have given me the confidence to rebuild my turbo, oil cooler and up pipes. thank you so much for the clear precise videos.
96 F350 4x4 cc 583, 000 miles
Your a ledgend bro, love seeing the tear down of each location of oil leak! Love my 7.3 and cant ever watch enough a about it thorough your channel!
Thanks for all of your great 7.3 content. Mine is a 2001 Excursion w/ a 7.3, 194K miles that recently was in the shop for a pretty bad oil leak(s). It was $$$ but it's leak free now. Although I don't do the work on this engine myself, I do my do-diligence by learning as much about the engine as I can so I know what the shops are recommending. Again, thanks and I'll be looking forward to more great stuff!
Thank you 😊
MY oil pan was leaking, bought a new oil pan and the Morso oil pan gasket.
I lifted the cab up,rested the cab on wood blocks on the frame.
I lifted the motor with a engine hoist slipped the oil pan and the gasket right in place.
u don't half to pull out the motor and flip it that's the old way of doing things!
It's been a year and everything is bone dry .
8 hour job.
Fantastic
I have watched a few of your videos. Great content. Thank you for making them.
Thanks Clint I have a whole new respect for the 7.3 I’ve only had mine for about a year and now have done my share of repairs of the leaks but without your help I might not have got through it we all know the “ shakes phone mechanics “ on UA-cam thanks for NOT being that guy lol just saying
Thank you for the video very well! Presented, it's credit to you. One of the better ones out there
another great one bud thanks again!
Hi there Tony from Australia I do have a pretty good valley leak hard to track down right I think it's coming from the back of the hpop.thanks for the up loads they are so helpful .
keep up the great CONTENT !
Bad ass video again. Keep up the good work 😎
Spot on mate thanks
Im not really a commenter but if it help you create those rebuild and replace videos you mentioned. here you go. nice work Clint
Thank you
Great video...as always☺....
I need help!!...
Where do I order a plenum gasket set for a 97 stroke....part stores don't have it...the only place I found says shipping is 5 weeks...this is my work truck 🤦
have you ever seen the bolt where the engine hoist bracket thats located in the valley leak?
clint could the pedestal or turbo leaks or any other mentioned here for that matter cause some leaks that go to the concrete I’m identifying like 5 and don’t want to use oil fill
Clint long time no see my guy… I’ve passed through the veil of impossibility with your vids, now on to just this simple topic
New season coming soon
Leaks from under the turbo, started after mechanic replaced a return fuel line on the passenger side.. initially a small drip, now it puddles AFTER the engine turns off. No drip while running, then dumps when the engine is turned off.
Right on
i have a 1997 7.3 ,. when i start the motor it runs for about 2-3 second and then starts chugging for a couple of minutes and then smooths out some what and the check engine light coms on . i have replaced the IPR and this still happpens, any ideas what could be wrong??
1997 7.3 ICP and exhaust presure sensor and ipr all replaced??
I watched it again!
😁❣🫱🟢
Any idea what would leak oil onto the starter? In my case, it's not the valve cover gasket (passenger side). Thanks.
Could be The dipstick tube Oring ...
I was looking for a diesel leak in my valley. Didnt see anything from the bowl or other usual fittings. However, i did see some oil collecting around that square drive drain plug to the drivers side of hpop right behind the timing cover. I am open to suggestions and i have pictures. Just didnt know if i could tighten that plug or if its coming from somewhere else. Thank you.
The oil leak if it was me doing the work I'd be looking at the hpop gasket or timing cover seal The fuel leak take baby powder and lightly blow a dusting on lines and filter housing and or pump if its a early 7.3 at some point the dusting of the powder will get heavy enough to show where its wet and where its leaking from < it may only be leaking fuel when pressure is high
@@CUSTOMWORKS7.3PSD yes sir thank you it's an 01
@@CUSTOMWORKS7.3PSD I think it's because I changed my water pump before i discovered your channel. Lol
Do they use loc tite on the hpop oil resivore bolts thanks
NOooooo just the loc fittings where the hpo comes out
thank you CW
I have a 1996 ford f250 7.3 with 202,000 miles and it has an oil leak in the valley but I cannot find it. The oil pools around lift pump and then more towards the back when it looks more. When it idles i cannot see it leaking it seems to only leak while driving. Any idea on what that would be?
autozone has a uv dye with uv light and glasses both for ac and oil leak detection Clean the valley out completely install the dye let it cycle clean the valley again and first sign of leak use the light and glass's you will be able to identify the leak
@@CUSTOMWORKS7.3PSD thanks will try that soon
@@CUSTOMWORKS7.3PSD I found my oil leak, didn’t get to the Uv dye but I cleaned up the valley, under hpop pump there was a lot of fuzz like material and seemed to absorb the oil and let it leak to the back cleaned all that up and found the snap ring of the back of the pump leaking. Is that hard to fix or do I need a new hpop pump
@@kevincontreras6472 not difficult unless it was previously remand Because they glue the cover on So if its original remove the pump riff raff has the oem gasket ring use a c clamp to press the cover down keeping the cover side straight up in a vice remove the snap ring and slowly tighten the clamp because the inside is under spring pressure remove cover install new gasket ring put all back together I believe riff raff has directions with pictures
@@CUSTOMWORKS7.3PSD I am planning on upgrading to an adrenaline hpop you think I should go that route if I can get one
Thoughts on ebpv delete turbo pedestals?
best delete you can do also don't forget to do this to the wire you disconnect just cut the end off at plug and solder this to each lead ua-cam.com/video/rg725mTLo6Y/v-deo.html
Thank you sir!
Now show me how to pull an engine out of an E350 with a 7.3!
I had to doit once ..is an absolutely pain in the ass..good luck
ok here's what I think is a leak from the front cover gasket. I haven't done it yet, I wasn't sure if i need to replace the front cover itself or just the gasket. What do you think? ua-cam.com/video/lihdHZUVSxM/v-deo.html
Well that was cool,, but You need a new timing cover. Soo oem timing cover , gasket set with ford or IH gray gasket sealer and enough to do the pan as well If your talented and mechanical inclined it can be done in frame But depending on what you have done for maintenance it could be a good time to pull the engine do up pipes all gaskets a good once over up to you
Love the 7.3. Wish diesel wasn’t over$5 a gallon. Thank Biden.
It was not bidens fault maybe blame your self cause you could get your ass up and do something about
Still driving the 97 7.3 I wanna make a little power but it's so reliable I just keep her stock
cool thing about diesel engines is they were originally designed to run on peanut oil. Nowadays you can make your own fuel, most people make biodiesel from used cooking oil. It's not that hard to do
Just turn the stupid music off
Thank you