Back up Camera Wiring - How to wire to the Reverse Light
Вставка
- Опубліковано 11 жов 2024
- How do you wire a backup camera to the brake/reverse light? Watch to find out how easy it is!
See all of our back up cameras and systems:
www.qualitymobi...
There are a couple of ways to install and wire a back up camera system. We go through the different methods and explain the pro's and cons of each method. Then we take you through the process of removing the taillight and how to test for power. We explain vehicles with light control modules and the problems they pose. Then we make the connection at the taillight to a back up camera system. We recommend using a relay whenever wiring a back up camera system to isolate the system from the light control modules. Please leave your comments and questions below.
Love a 'how to' video, with the how to and without actually doing it
Great vids but pls switch off the music when you are talking, it's so hard to pick up what you say otherwise, thanks 👍👍👍👍👍👍
The presentation of the video and the guys professional and knowledgeable demeanor is perfect here for an instructional video. However, it was assumed that your viewer would know how to use and interpret a multimeter reading. As an electrician it's my experience that a lot of electricians don't know how to use a multimeter, let alone the normal public. Also I got no wiring instructions. Did I miss another video?
DITCH THE MUSIC!! (Otherwise, great.)
What did you say? Can't hear over the concert music.
Thanks for showing us
You bet!
@@Qualitymobilevideo u suck
I heard you just fine. Good vid. Helping confirm things for my 2014.
Thanks for the video but it would be nice to turn off the background music while you're talking providing us the information.
You can simply trace out that backup light wiring in your fuse box there by saving you the time to run the wire from the back of the vehicle to your radio, its how i did my Ford Escape. relay was still necessary. Thanks for sharing.
Thanks for the useful video. I connected my camera just to the RCA connector and the reverse cable at the back of my HU and it works fine. I guess it gets power from RCA cable and signal from canbus. Is that ok and safe or I still need to connect positive and negative to the reverse light?
For the DIY market, no visual example of the red wire connection to the positive wire of the reverse light. Do you trim and splice, solder, or put in a clip? I guess I'll trim the wire, wrap, spot solder and use heat shrink insulation, since there's nothing specific here.
Music is so high !!! Other wise great vid as Tom Patterson said :)
Ok thanks!
Very informative, but that music is so distracting mate..
Yes, I am somewhat hearing impaired and I can catch most of what he is saying but the music definitely makes it harder. Perhaps if it wasn't as loud as it is, it would be better.
Informative video. Thanks.
Glad it was helpful!
@@Qualitymobilevideo I wired my backup camera wires to the reverse light wires. It works!
Get rid of the music it makes it hard to hear you
Silly me, I thought this video would show how to wire the backup camera to the reverse light... My bad!
Is that loud music necessary while we could hear you voice in the background.
Good information. The music can go though.
Why would you want to link it to the brakes and not the reverse light instead?
This video literally didn't answer ANY of the questions I had regarding this issue!!
Ok well what are your questions, we're happy to answer them.
Same. But he answers a lot in a video title "5 Step Backup Camera Installation" which could still be improved with a simple diagram and an actual demonstration of the installation.
+Quality Mobile Video ...Can you tell me where to connect the camera if I want it trigger when the turn signal is on? I am thinking about making blind spot cameras. Can I connect two cameras to one display this way? I appreciate the help
@@dBolotok brilliant idea ;)
Hello, you channel is very helpful so as you videos. I was have a little problem today with reverse camera. I was connect everything and i was located a riverse light. On my car Peugeot 407 tails light have a one connector for all lights (stop, fog lamps, blinkers, position....) and have a only one ground(yellow-green) wire and its connected on chassis. I was located the reverse light wire and connect red wire of camera on that wire and black wire on metal piece on trunk lock mechanism. When i was in reverse the displey was dead. Something was burn and all is dead. I Don't know what i was do wrong, only thing can be that so i wasn't put ground on the ground of tail light. What do you thing, what was wrong.
you didn't say anything in this. these are the options. how about showing us? no one shows us. and i agree on that music, not needed.
Here's the installation one: ua-cam.com/video/TqgMu3K6tNQ/v-deo.html
Maby I'm stupid, but can I put the plus pole cable between the lightbulb and connectors?
mate, i am stuck, i have hatchback mazda 3, the wires connecting to reverse light are too thin and its up the boot, is there anywhere else i can connect camera to(don't want to connect to lights in this case) please let me know
I hope all your videos after this one didn't contain that music. It was kind of like trying to carry on a conversation in a bar on a first date. I heard you, but I didn't retain a damn thing you said.
I had jokes ready but these comments say it all 😄 🤣 😂 😆 😄 🤣 😂 😆 😄 🤣 😂 😆 😄 🤣 😂 😆
This would have been informative, but the background music is way too loud. And you NEVER CONNNECTED THE CAMERA!
I tried CC but the guessing by the CC auto-caption leads to some nonsense statements.
This video is very informative, but the background music would be more suitable to a rock concert, rather than an instructional video. Your voice gets lost in the mix if any volume is used.
We were rookies back then!
Prius has a built in plug for rear camera in the car rear door panel, just take of the cover and find the white socket. there is no need to mess with back lights.
Does the Prius C 2012 have a built in plug for rear camera in the rear door panel as well? What are the next steps after locating the white socket? I’m trying to install this myself but don’t know anything about car
Is it possible to wire a camera with an Anderson plug connector to have continuous power and simply connect the camera to the rear bumber bar above the Anderson plug? Thinking of wireless so easier for a large station wagon
What would cause a camera to be stuck in Reverse Parking Camera mode and only shifting to normal mode when the car is either in Reverse or the doors are open?? This issue has been occurring since I got the car back from the dealer who flashed the Body Control Module to activate fog lights...
Hi, I have installed my back up camera successfully and it is recording at all times. I don't think I did a good job on wiring my positives to the back up light, so I'm not sure if that is the reason why my parking assist doesn't show up. It's just a plain video of my front and back up camera once i turn my car on. I pretty much just plug the positives into the connector to form a hook instead of using a wire splicer. Do you think my camera just doesn't come with a parking assist function or did I do something wrong when I set it up?? Thanks a bunch!
Can I connect my Line out converter to my brake or reverse or parking light switch for +12v to power it in order to have control over it so as not to leave the amp on to drain battery?
Can you hook it up to either taillight
I have a 2015 Chevy Silverado. Do you have any recommendations on how to tell for sure whether I need a relay to install a backup camera?
Hi are able to show how to install the side view camera/ blindspot camera thanks
Yes, I agree with others. Not much info, too much music. What little info he shares is a good starting point, but nothing more.
How to wiring reverse camera with relay? So that the camera will not off even the car is started.
can i power both camera n monitor to the reverse light?
what i want to know is, will there be any issues if i ground the camera n monitor to the reverse light grounding wire?
This is not ideal but it should work.
thanks!
I'm having problems with the wiring on my 2003 Windstar because of the Rear Electronic Module. When you talk about wiring in a relay, is there a way to run the relay off of the reverse light wires, or are you saying that you have to control the camera manually with a switch you put somewhere.
Eric, you will wire the relay so that the electronic manual controls the relay. These modules output AC and create problems for DC electronics.
What if I have a solid black wire and the other is green with a black stripe
How to you actually connect the wire. Lol that’s literally all I wanted to know and you didn’t say
What does white on black is ground and red on blue is positive mean?? Whats white on black and red on blue? Can you demonstrate wiring the backup camera power onto the brake light?
That usually means a white stripe on a black wire.
Hi I have a question: can i power both camera and monitor with the license plate light? I'd like both the camera and monitor to turn on when I start the car.
Yes you can, however; we do not recommend that method especially in newer vehicles due to the light control module. Most monitors have a trigger wire that you will connect to the reverse light and this provides the signal to turn the monitor on.
I have a Pioneer AVH X2800BS head unit in a 2012 Toyota Tundra. Can I run a single power wire from the purple wire (back up camera wire) from the head unit to the reverse brake light power wire? Shouldn't this power and trigger my camera in reverse if the RCA is plugged into the back of the head unit?
On a head unit with back up camera input this is the correct way to do it, you will need to wire the camera to accessory power so that you can view the camera anytime, like when towing a trailer.
Is it possible that camera is on for 24 hrs. whether engine is on or not also camera screen is automatically on when gear shift is in reverse mode?
Well if you wired it directly to the battery. but that would drain power
Let me rephrase my question. If rearview camera's power line is connected to the power source other than backup light, how can make it automatically on when the gear shift is in reverse mode? (Because there is no connection between the rearview camera and reverse light) I mean, how do I connect extra line and how?
Hey I have an 2008 Infiniti g35 and I have no clue where to start on how to set up my back up camera to the rear light as a power source
Can someone help me when i connect wire to my reverse bulb and if i engage reverse gear camera keeps going on and off into reverse mode why is this??? My reverse bulb is not doing this its constant
Your vehicle is likely a newer one and the light control module is a PWM unit and causing this. The only other possibility is you did not unplug the bulb when you tested the reverse lead and actually have the ground side.
showed location but how to actually wire the red camera wire to reverse light wire?
Presenter: I'm going to show you how to wire your rear camera to the reverse light.
Also presenter: Don't wire the backup camera to the reverse light, use a relay.
ALSO THE PRESENTER: *DOESN'T SHOW HOW TO DO IT WITH A RELAY*
When I wired my back up camera to my reverse lights it shut off my reverse lights and powered the camera, why is this ?
Hi I am looking to wire my reverse camera to my cars reverse lights. The first time I tried it, i think i grounded the wire wrong which the caused my alternator to become defective and cause the check air bag and abs warning light to come on. It also made the Blowers turn off. Do you think this was caused by me because only a week before my car was being worked on at a body shop in which they had left the ignition on for hours without having the actual engine running. I am looking to give it another attempt but am scared because i don't want to dish out alot of money having the alternator replaced again.
It is not likely you caused this issue.
Is there a problem if i connect rear camera with the parkeringsensor the same revers light
You may want to rename the title of this video.
Kevin Smith o’
Kevin Smith , like How to find reverse wire while listening to Loud metal music
New title “How to tell you in theory how to wire a camera without actually showing you what to do”. Agree, the music was distracting, but you know that from the 50 other comments about it.
We have half a dozen videos of showing actual installations of cameras, this was simply an overview of the concepts and locations of essential parts.
@@Qualitymobilevideo I figured it out by watching another video. All is working well now. When you’re on a mission to get something done, you figure it out.
Hi I installed a HDE reverse camera ,how can I installed a monitor on a licence plate camera
You may want to change the title I was ready to lmfao and ask how the brake light wired in would work
Hello sir! I would like to ask what do you think about my reverse camera getting blur the display when im going to reverse. Do you have whatsup or messenger so i can send you video of my wiring, do you think it is lack of positive 12volt supply? Thank you sir!
I have a limo . after the battery died the backup camera and the monitor of DVD did not working . May you help me to reset them . Thank you
Did you replace the battery?
When it originally died did you try jump starting the battery?
When it originally died did you try jump starting the battery?
When it originally died did you try jump starting the battery?
I like the video, but the backup music is distracting.
Having a link to the the video about actually.. physically connecting the back up camera to the back up light helps alot. When we search for how to videos. Yours comes up.. but this video isn't helpful
So, just for nitpicking: that is not the positive and ground, but the positive and minus of the light bulb socket.
We are trying to hook up a camera to our daughter's AVH-X45800BS, but it came with NO instructions. We placed the RCA in the back of the stereo. We did NOT hook the red wire coming off of it to anything, although we have a purple reverse wire on the harness. At the back the black cable connects with a pin connector NOT AN RCA, then there are 2 wires (red and black) that are coming off of. We connected the red to the backup light and the black we grounded to the vehicle (04 Jeep Liberty Renegade). Although the picture changes to camera view when you put the car in reverse, the picture is BLACK. Where did we go wrong?
+EyesOffManOnTheWORD More that likely the vehicle you have has a light control module that is actually outputting AC instead of DC. You will more than likely need to use a relay to actually output DC. Temporarily connect the power lead of the camera to the battery and see if everything works. If it does, install a relay.
purple (harness) red (camara) red (reverse)splite together ....black (camara) just grounded to the chassis
How do I know if my car has the light control module?
Yeah, but how... I agree with Kyle
loud music kills it all
how bout you make a video without any background music so you can be heard clearly, and then you actually DO what you are talking about in the video, instead of just talking about it and referencing other videos. This was not a useful video.
If you just take a look at our channel, have over 600 videos, and about 10 on backup camera installations, some focus on specific things, some are just overviews. We can't make the same video over and over again. This might be more helpful to you: ua-cam.com/video/zFbVKAMYEqI/v-deo.html
Get rid of the music. It’s distracting. Great video.
This video was 'How to find your reverse light cable', not how to wire it
I have a direct port to connect RCA cable and got power from backup light. However, it shut off within few seconds. How can I fix this?
You will need to check the voltage with a volt meter, you likely have a voltage drop and may need to use a relay
Quality Mobile Video but how can I use a relay. There is a stable power, reverse power, and ground everything is there? Can I use that or do I have to get power from cigarette lighter?
How do u do it though? U show the meter working but how do u do it? That's y were watching, to see how not watch u do it
Watch this: ua-cam.com/video/zFbVKAMYEqI/v-deo.html
What poxy distracting and unnecessary music!
Hello there, aloha everyone! need some help here if any? I got one of those camera, and ive installed it, followed every single instruction for installation! I have a alpine ive head unit with a reverse trigger, i connected the camera power source to the reverse back up light, and the reverse trigger from the head unit to the + reverse back up light! In the morning is fine camera works ok, powers on when switch the gear to reverse and triggers the head unit to show the back up camera, but the problem is at night, yes! Its When i turn on the tail lights and step on the brake pedal, my head unit triggers to camera even gear is not on reverse, there is no image since camera on powers when i put the gear on reverse! So yeah at nigh when i turn on the tail lights and every time i step on break this happens, it triggers my head monitor in reverse, i tried and check all the wirings, and even replace all the tail light, brake signal light bulb new, but its weird when i remove one of the brake light bulb and turn the tail lights on and step on brake its doesnt trigger my head unit monitor to reverse,! Is there anything im missing? Really need help, thank u in advanced, mahalo!
sooo how do you hook it up???
Turn the music down!
12v trigger for the monitor defeats wireless option on many cheap cameras ;(
Show how to wire it please
We have this video which goes through the entire proccess: ua-cam.com/video/TqgMu3K6tNQ/v-deo.html
Music is way to loud.
What relay did you use?
?
why the hell would you want to wire it to the break light? It will only come on when you hit the breaks!
You wire it to the reverse light. The reverse light is located in the "brake lights" unit
Could have been useful if we could hear you over that awful "music"
ok
How to wire a backup camera (proceeds to show how to test voltage on the reverse light).
2004 Jeep Liberty Renegade how will I hoped up a back up camera to my JVC Double DIN ... if you need more information just private message me on here ... thanks
can you point me to your relay wiring video, i cant find it, thank you
Here you go! ua-cam.com/video/FTO5KfIyaO8/v-deo.html
Sooooo, what’s the answer
WHAT PREVIOUS VIDEO?
ua-cam.com/video/zFbVKAMYEqI/v-deo.html
Sorry whaaaat? MUSIC BLARING
I couldn't hear a damn thing. Which didn't make a difference considering you didn't actually hook up a backup camera in the how-to video for hooking up backup cameras.
This is why UA-cam removed dislikes. Ffs.
Thanks for the feedback, we were rookies at editing back then.
Yeah - agree with the others. That background music is unnecessary, annoying, and makes it difficult to hear you. Might have been a good video otherwise!
Dude, the music is to loud
You touched the bulb bare hands 🤦🏼♂️
GAWD-NO NEED FOR THAT OBNOXIOUS BACKGROUND NOISE!
Who else is confused
You didn't show how to install it
We didn't label this an installation video. This is our backup camera installation video: ua-cam.com/video/zFbVKAMYEqI/v-deo.html
75k subs for a guy who calls a reverse light a brake light. Gees.
Actual dialogue from the first 30 seconds of the video:
0:16 "going to talk about how to make the connection to the reverse light...."
0:23 "getting to the reverse light wiring...."
Ending:
3:48 "that does it for out different options on how to wire a backup camera to the reverse light..."
Why do people have to make a training video with music blaring ? Whats the point, just make music videos instead
The never ending music are quite annoying when trying to hear what they say, please stop doing that !!!!
Is there a reason you have that music blaring in the background? It takes away from your goal which is to teach us something. I couldn't stand it anymore and moved on. I shouldn't have to try to listen to what you're saying while flitering out the annoying music.
great video bloody awful music
Why the helm is there stupid music blaring