HOW TO: Add Apple CarPlay to a 2016 Ford Edge with Sync 3
Вставка
- Опубліковано 2 жов 2024
- GPS Navigation, Siri, and a familiar UI are all great additions that Apple CarPlay brings to your drive. Ford added support to their Sync 3 systems starting in 2017, but 2016 models can take advantage with a special part.
Part Number: HC3Z-19A387-B -Ford USB Module with Apple CarPlay support
With only that $75 part and a few minutes of time (plus a 7/32 socket), your 2016 Ford can take advantage of this upgrade too!
THANK YOU FOR THIS VIDEO. I ordered the part, and my boyfriend watched this video on the toilet and came out and had this done in 5 minutes 👏🏼
I also have a 2016 Ford edge, same color combination as yours. I skipped pulling the dash apart by getting a long flat blade screwdriver and starting at the top left corner of the USB plug wiggled the USB plug out of the compartment. Then just connected the new CarPlay plug and pushed it back into the compartment hole. A lot less trouble than tearing apart the dash.
Thanks, man! Just got a 2016 and I was about to tear the trim apart when I found a small metal paint can opener. One pry to the bottom, one pry to the top and the USB module popped right out. My issue was the connecting cables wouldn’t come out very far so I watched the video again for where the disconnect tabs were. Boom. Done in about 5 minutes. No marks to the USB housing or trim. If I hadn’t found that opener I was going to follow your video, so thank you for posting this video. It was quite helpful in the end even though I went a different route.
Just made the upgrade on our 2016 Edge. Our Sync firmware was arlready updated to 2.0 so it was a plug and play swap. Took me I'd say 20 min tops. Spent more time cleaning than I did doing the work.
This was super easy! Thank you so much for this awesome video. I was intimidated taking off the trim but it really did snap out and back in easily and overall the install was simple. I can’t believe the people at the Ford dealer wanted to charge that much for this.
Just wanted to say thanks for your video. Purchased the necessary hub on eBay for $29 and after 30 minutes of installing (I took my time), everything was up and running great. What an improvement!
Glad it helped!
Great video! Took me around 20 minutes from start to end.
Thanks for this video mate. Your vid made the process super simple and I appreciate the time you took to share. Cheers!
thank you works well without any programming
This can be done in about 30 seconds without taking anything apart. The module pops right out with a trim removal tool
Just tried for 20 minutes putting all my strength into trying to get it to “pop right out” with a trim removal tool. Yeah. Not happening.
Update: Used a screwdriver, cut my hand open, but got it out!
Is it possible to take out the hub without remove all this part?
Thanks so much for the easy to follow guide through this project!! Your calming voice and nature helped keep my stress level down. Amazon wanted ~$120 for a CarPlay compatible USB module. I purchased an Edge specific one at my local Ford dealership for $42.
This made it incredibly easy! Thank you so much!
Worked perfect. Thanks for making this tutorial
Great video and absolutely perfect result. Pro tip, those tiny screws are perfectly resolved to falling into the cavernous center console recess, down into the quantum dimension, never to be seen again. Side note, three screws are sufficient to hold the compartment in place, although my ego has taken a beating.
Same thing happened to me today, lol. Zero rattle, even with 12" subwoofer.
Great job. You made it look so easy. Took a little longer than you did it. But it works... Thank you...Good Job!
You can skip tearing your center console apart and just pop the usb hub out by using a skinny flathead to pop it out
Hola a todos! Este mismo proceso serviría para un Ford Focus del 2015? Gracias!
Thx Jacob - just purchased a 2016 Edge Sport. The dealer said the labor would be $120-150 plus the $63 part. I bought the part online for $38. I upgraded the Sync 3 software to version 3.0 and had my laptop perched on my dashboard and watched it as I tore my console apart. Your instructions were perfect and it made the USB hub swap a breeze. Fired it up and it came up just like yours did. Kudos also to Ford for providing free software updates! Great to have Carplay again.
Bruce Bridges Awesome! That’s the type of comment I love to see. Glad this video was able to help you out!
Agreed! Did the same as mentioned above, and well worth the time for DIY instead of giving the $$$ to a dealership.
Can you link the part you bought?
Can you please provide the link for the part.
This can all be done in 30 seconds by popping the old USB hub out without taking anything apart.
How to do it on edge 2016?
If you want to take all that apart you can or just pop off the trim piece behind the usb where the little led bulb is and put your hand behind there.
Just got my Carplay USB Hub for my '16 Edge SEL 3.5L today and I did it the more simpler way by using a plastic pry tool and getting it out that way. It didn't break any clips off of the old one at all and no taking apart the console :)
If anyone is looking for the part I bought it on eBay here:
www.ebay.com/p/Ford-Controller-HC3Z-19A387-B/1183339748
Worked PERFECTLY! Unplugged the old and in with the new and it recognized it right away!
Just ordered that part for my 2016 titanium, hopefully will be able to do it with a flat screwdriver or prybar as well since I'd rather not take about my console and brake.
@@sspain2149 Were you able to get it out with a screwdriver without issue?
John Seguin It was a pain in the ass but I ended up just using a small pry-bar. Minor scratches on the plastic housing but hardly noticeable. I also bought the one he linked in the description and it works perfectly.
oEx0duSo If it works because I ordered one from Amazon and it didn't work for me 
oEx0duSo I want to see if this works to order it. I don't know what you recommend me?
Great video, I’m trying to do the same thing on my 2016 Lincoln MKX, any tips on that model?
Whats the link for the firmware update?
The video was very helpful. I purchased the USB module from the dealer. The current Ford part number for the USB hub is HC3Z-19A387-F.
What is the part number for the upgrade
I am about to do this upgrade, hopefully today but no later than tomorrow however in a Taurus. Its a much easier upgrade in my car though, just a small trim panel a little larger than the USB ports has to be pulled out in order to remove the USB ports and connections. Should take me about 5 minutes. Removing those huge pieces looked like a pain. If mine was so involved I probably would not bother with it. You get a lot of the functionality with Sync 3 anyway.
davva360 Yeah, those panels were a little more challenging to remove than expected. I’ve removed dashes in trucks, sedans, and vintage muscle cars for one reason or another, and the retaining clips on the Edge are some of the most stubborn I’ve dealt with. Some people just pry out that USB adapter as a result, but I was wanting something less destructive. It just takes a lot longer....
THANK YOU FOR THIS VIDEO. I ordered the part, and my boyfriend watched this video on the toilet and came out and had this done in 5 minutes 👏🏼
Just got a 2016 Ford Edge and this video helped me to easily find and install the upgraded hub! thanks for this video!
I’m so lost , confused, and🤬🤬🤬. I had a used 2017 explorer sport where this came with. Some idiot on a cell phone totaled it, now I have a used 2016 limited explorer with sync 3.4 and ford touch. I’ve been researching constantly for days, don’t own a computer and my usb is single with a Sd card slot. Video after video, forum after forum, even talk to 6 people at ford dealership that all looked at me with no idea and passed me to the next. I’m at Ford but they said you have to order whatever it is you need? Online, can’t help.
I’ve lived with an iPhone and iPad my life. I don’t know computers except from when they first came out. Can someone please help????
I bought that part and installed it and updated the software but still no CarPlay. I also still have the same buttons as before, no new buttons.
It was a false update. I finally got it to work after this new update! 🥳🥳🥳
You lost me at taking the console apart. Sirius stopped working properly on my 2018 Edge last month.
Thank you. I have been looking everywhere to see why it didn't work. This was very helpful.
Thanks for the video. Do you know if this can be done on a 2015 edge?
Also interested in 2015 edge titanium. Anyone know if part is compatible?
@@reincarn8tionI haven’t tried it yet.
Just followed these instructions with great success. Like others, I lost one screw and I still have a 7/32 socket stuck in the dash which I hope to retrieve when I get another one.
Does the Apple CarPlay have maps as well? I didn’t see it as an option in his video
HI. thanks for the video. but surely the connection is only done with the cable?
This worked perfectly - thanks! Note for people who did not watch carefully (like me, apparently) - the 4 screws to be removed are all black. Do not try to remove the silver screws on the bottom - they are not the same size and are not part of this process. The video shows the right screws, but I saw the silver ones and got confused.
Mine is in the console
Thanks so much for making this video! I just did this on my 16 Edge sport. Only difference on the sport is the fact that there are more cords for the park assist buttons so if anyone has an edge be careful with those. I actually did not own the correct socket for this so I had to run to the store ( oops ). Other than that the the install went very well due to how descriptive your video was.
Good to know! Even though this wasn’t 100% accurate for you, glad the video was able to help you out anyways!
I have a 16 for edge but my screen is much smaller will that piece work?
i ordered hc3z-19A387-b and hc3t-14f014-bc came. every site i see has shows hc3t-14f014-bc and the box shows the other part...
Does the car have to be on for carplay to work. i installed the other part number. carplay didn't work, so i took it apart
The engine doesn’t need to be on, but the radio does. I’m not sure what the difference is between those two parts. I’ve been trying to find something authoritative and haven’t found anything one way or the other if it works.
Make certain you have the latest firmware in your car too. CarPlay is only supported Sync 3 version 2.0 or higher. You can download it direct from Ford through their Owners website. Also, just to cover all the bases here, CarPlay will only work when the phone is plugged in through USB. Hope this helps!
Beautiful -- thank you for this! I was really nervous to try it, but it was easy. I think I watched this six times before trying it! FWIW, my center console trim came out easier than in the video. My only tips: Don't hurry, have plenty of light available and use the 7/32" socket (or tool) as specified. (Don't try to fudge it with the closest metric or something.) Hats off to you, sir!
Just finished using your video. Thanks for the simple, easy instructions. The cracking sound of plastic made me nervous but everything worked out! 😅
Hey
Thanks for doing this video. Can you please share me the direct ford link to buy this product. Or else any certified product link. Better you can add in your description too.
Thanks
Well, the part number itself is already in the description. That lets you do a simple Google search and get it from wherever is best for you. Depending on where you live, it may be cheaper to pick it up from your local Ford dealer instead of paying to ship it from an online retailer.
Thanks. This video is excellent. Anyone can do this with little experience
Thanks for the outstanding video. I got the part for my wife's 16 edge as an Xmas present. Install was super quick and easy because of the detail you provided. Thank you.
How long was the software update?
Thank you. Followed your directions and it worked perfectly.
Awesome video! Question for the group: I have a 16 Edge Sport with SYNC version 1. I noted my XM radio will not go beyond ch. 184. How can I upgrade this system? Pls advise, thanks!
Very good instructional video. Easily understood, took through entire process. Good job Jacob.
This video worked perfectly! I was also able to pop the piece out as other comments suggested saving a bunch of time but if I had to go the full monty (which I started) your instructions were perfect!!!!
You know all you gotta do is pull the usb housing out. You are extra when you took the whole console apart. But I guess good job
were you able to do it with jus poping it out?
@@jincheng8872 yes just need needle nose pliers and just pop it out it’s just plastic tabs
Hi Jacob. Thanks for your very usefull video. I live in CR and I bought the Ford Edge here. I already downloaded the sync 3 version and bought the replacement part you recommended but the car shows a message saying that the usb is not compatible with the system. Any ideas on what else should I do to make it run ?
Did it. I don’t see maps. Is that normal?
I tried this and didn't work. I have a 2016 Ford Flex - I did download the 3.0 Sync software and installed it. Then I replaced the HUB with the correct hub (same part number and ordered from Ford).. Even changed my cord. No luck. My device is detected, but it doesn't start Car Play - any advice?
Did you figure it out? I’m in the same boat now.
I did figure it out. In order to make it all work, I had to go back and Install Sync 2.0 and then sync 3.0. I found the solution by googling the issue and found a link to a guy who made the update files. Search Synch 2.0 install for the Flex and you should find it.
@@Liz123789
Thank you for the video, will get the new USB Hub for my 2016 Edge. A small correction, CarPlay was officially unveiled at Apple's WWDC conference in June 2015, and the first car worldwide to come with CarPlay was the 2014 Ferrari FF, probably a beta version, so BMW could not have had it in 2010.
I appreciate all this guy did to replace the USB ports, but there is a much simpler way. Take a long handle flat head screw driver and slide it under the left side of the flange on the USB module and twist the screw driver working your way up and down the left side. After a few times of doing this the unit pops out some and I was able to pull it out, unplug it, and plug in the new USB module and snap it back in place, took just a few minutes. Much simpler than taking the dash apart.
idk why i laughed when he said " this just pops off.... *struggling* like so!" lol
Thank you! This was extremely helpful and our trim actually came off easier than yours so was even quicker.
Thank you for this video. Your instructions were super easy! I read some of the comments beforehand, and picked up a trim tool just in case I needed it. The tool was not needed. I’m really happy to have this accessory now. Thank you so much!!! 😊😊
I'm guessing this new part isn't required for Android Auto. Can you confirm?
Thanks for this video. Followed your instructions and it worked perfect
My mom had sync 3 version 1.0. Since it is only version 1.0, would she still be able to get Apple CarPlay by replacing the USB hum or would she also need to pay to upgrade the version of the CarPlay?
Hi Jacob, I followed your instructions step by step and now I have Apple car play on my Ford Edge 2016 titanium. Thanks. The only difference was the part number. The dealer had the HC3Z-19A387-E and it works fine.
Note: sync v3 needs to be done first , then the hardware installation.
Hi I have an edge sel 2016 sync 2, is it possible to upgrade if I purchase this part from Ford
I have A question.Would that work for a 2015 Ford edge titanium?
Just bought a mint used 2016 Ford Edge Titanium and these directions were easy to follow and I had Apple Car Play up and running in no time! Thank you!
I just bought a 2016 edge titanium as well and can’t get the update to happen. I’ve tried wifi and USB. Did you find a helpful video for that? I don’t have the settings some of the other videos show
@@oliviahutch17 my 2016 Titanium Edge had SYNC Version 1 when I bought it. I had to download and install via USB to SYNC version 2, then download and install SYNC version 3 and that worked! I could not go from v1 to v3. I found a site where someone put v2 on their Google drive and shared the file. I will put the link below. There is a READ ME.TXT file that comes with the download, be sure to READ that before installing. You will have to erase your USB and format it to EXFat. Then download the zip file. I opened the zip file on my Macbook using the app "The Unarchiver" (saved the unzipped files to my Downloads folder). Once unzipped, you will need to copy all of the files (Syncmyride, etc.) in the folder "Update 1" to your USB (do not copy the folder "Update 1", only the files in it) and then install that in your car. You will get a message that it could not install because there is no more space or something along those lines. Don't worry! That means you did the first part of the install. Now go back to your computer and erase those files on your USB and install all the files in the "Update 2" folder, then go back and install those on your Edge. This should successfully take you V2!!! From there you will need to download from the Ford website, Version 3. Unzip those files to your computer. Again, erase your USB and copy the Syncmyride, autoinstall, dontindx files and install on your Edge. You should get to V3. You will need to buy the updated dual USB part (I got mine via Amazon) and install that in your vehicle using the directions from this video to get Apple CarPlay. I hope that helps and good luck!!
Link to SYNC v2 update files: docs.google.com/u/0/uc?export=download&confirm=ejc_&id=0ByldYbWwjAf4WUYyT2l0Zkl3S28
@@sweetcyn1222 Thank you SO MUCh for taking the time to reply to my comment and help me out. I spent so much time trying to figure this out! I've got version 2.2 installed and will do version 3 and my new USB ports tomorrow. Thank you again!!
@@sweetcyn1222 I did it! Thank you again so much!!
@@oliviahutch17 awesome!! I know it was a process getting it all done! Enjoy your new ride girl! 😊
Awesome, Will this work for 2015 Edge SEL ?
I did this last night. Besides breaking the sliver trim (easily replaced), the most challenging part for was also the hardest part of the vid. Thank you
Great video - I installed the USB port in about 20 minutes and I AM NOT HANDY. Thanks
Thanks so much! Just replaced mine in less than 10 minutes, for the part from fords parts website for about $60. Finally have Apple CarPlay!
Very useful video. Upgraded a 2016 Edge with no problems and REALLY enjoy having CarPlay
Will this work for 2015 edge with Titanium trim package?
Does it conect wirelessly or you have to wire it?
Went through the whole process .. still not working :( updated to sync 3.0 and everything! Any suggestions? Ford customer service was no help. Did you update the map/nav also?
Did you figure it out? I installed the part then did the update and still no CarPlay.
Thanks for posting this, got it done. I did what others did and broke the silver trim on the side on the drivers side and lost a screw. But I’m fine with that because it’s all up and working
Great tutorial, worked like a charm!
Jacob, any idea on why I would end up with the Edge not supporting the new USB Hub? It seemed so simple, and now my car is rebelling😱
Hmm... What happened? Is there no difference between before and now? Does the Hub not work at all? You installed the Firmware update too?
@@JacobMast thanks for the reply, a very well done video BTW. Yup still not functional, reached out to the Edge MACT group on FB, one suggested it was defective, and another said i needed to replace the APIM. This will be the 2nd hub i have to take out and replace. the first one was not OEM. So I'm just so very frustrated with this, I shouldn't have to pay the dealership to install this in order to get it working. Well maybe the 3rd time will be the charm.
Does it also work for the 2015 as well?
Hello! Great video. I have a 2016 Ford Edge Titanium upgraded to Sync 3.0. I have had 2 different people from Ford tell me 2 different part numbers: HC3Z-19A387-B and HC3Z-19A387-E. I see the "B" part all over eBay, but not the "E" part. I'm afraid to buy the wrong part...any advice??
Hmm... dunno anything about the “E” version. I used the “B” version, and haven’t had any issues.
might be the lighting color (blue vs ??)
@@8prot8 You are correct, its just the color of the lighting
I got the HC3Z-19A387-E, installed no problem, and my 2016 Edge SEL is saying “this USB device is not supported”. Anyone else had this problem? May I need the -B version? I don’t know why colour of LED would matter.
@@jasonlye3584 Hi Jason - I have the same vehicle and received the same part from my Ford dealership. I'm also getting the same message "this USB device is not supported". Did you ever find a solution to this issue? I'm running Sync 3 ver 3.0
Will this work for my 2015 Edge?
Is there a way to get Apple CarPlay on the sync 2 models ?
Thanks for the video and identifying those difficult clip-points where nylon pry tools make it effortless without fear of cracking something.
How do u take out the screws?? My wrench wont fit in the area at all. This is my only issue
Are you positive you can't pry just the USB holder out without disassembly?
Definitely can't, but they changed the bolts that hold in the compartment, They're nut driver size now.
Even after changing the USB port, my car doesn’t show car play. What else can I do?
You figure it out?
Is there anything else I need to do? My car is sync 3 updated to 3.0 plugged in the new part and still no CarPlay and I’m super frustrated any advice will help!!
Did you figure it out? I’m having same issue
@@kacycarpenter6600 yeah there’s a UA-cam video on here that you have to update the software to the newest version available and you have to use a usb drive to do it and plug into the car and match numbers up
@@OG_Honda_Gromdo have a link to the video by chance? Done everything like you listed above and still nothing.
I have a 2015 Ford Edge and was able to update to Sync three, but i want to know if i buy the USB module listed above will it give me the Apple Car play features?
Hmm...I don’t know. It comes standard on 2017 or newer Fords, and Ford says it’s available via software/hardware update on the 2016 ones. I can’t find anything saying that it will work on a 2015 model. Nothing says you can’t try it, but no guarantees.
Does this work on a 2015 Ford Edge ?
This video is perfect. Thank you, it was a great help!
Thank you so much for this tutorial you made it so easy and it worked so well.
this worked like a charm, great video, the trim on my Edge was really pretty easy to remove, I think I was done start to finish in 20 minutes
Ok so the 2015 ford edge is not compatible with this right? and are all 2016 ford edge models compatible with sync 3? or is it select models only?
Ford says 2016 and newer. Nothing says you can’t try it on a 2015, but no guarantees it’ll work. Either way, it’ll only be the models that have the large 8” touchscreen.
Does this work on a 2015?
Thank you so much for this! Super easy
Does this void warrenty?
It shouldn’t. It’s in Ford’s part database for this vehicle, which means installing this yourself is no different than changing the oil yourself with whatever’s listed in the owners manual.
Does this work for ford edge sport 2015 ?
Jacob, I realize this video is over 3 years old, but when I gave my dealer your part number in the description, he claimed it has been updated to a new part number ending in a letter "E" at the end: HC3Z-19A387-E. -- Can someone confirm this is really the Apple Car Play module still for Sync3 2016 Edge?
Interface Module
Part #: HC3Z19A387E Is what my invoice said. It works.
I should’ve added later that I used this part (HC3Z19A387E) and it’s been working perfectly for 7 months now.
Thanks this made it very easy .
Mine Worked great. Thanks 👍
Dude, thank you so much!