Hey, my shark vacuum starts, goes and then stops immediately. It gives me a red flashing exclamation point, red clean, blue dock and blue max flashing. Any idea what this could be?
Hi! Smitty! I have an RV750R01US that is flashing red clean and flashing exclamation point. I’ve cleaned the sensors, cleaned the filter, made sure there wasn’t hair stuck, and it’s still evading me. What am I doing wrong?
I’ve got an RV765 and have only had it for a couple of months! When i try to run the “max” light flashes, despite having emptied the vessel and cleaned the filters. Any advice?
Hello, I have a Iq shark the code is a exclamation point red light it says suction low clean and empty bin I did all that it will start and go 3 seconds about then flash code again ,, what now do I need to replace somthing I did all the cleaning and all the simple stiff. Please help..thanks bless
Having issue with the red clean coming on an ! Flashing red Just after a few seconds of running this happens what could it be and how can I fix this???
My shark 750 model robot runs @3 ' then stops with 2 flashing lights, 1 on the clean button, and 1 just left above the clean button. Please help. 3 days before this happened, it was making a loud noise for @ 2 -4 minutes then the noise went away.
I have the 750. It will clean for a couple minutes then just stop and the dock and spot lights flash blue. I check and there is nothing stuck anywhere. Even put all new brushes on and new filters. Any idea why?
My dock light (blue) and clean light (red) flash simultaneously when I hit the “clean” button on my remote. I clean the sensors and powered it off for five seconds. Turned it back on and this still occurs. Do you have any other ideas of what the issue could be?
I have the ion rv750, turned a year old at Christmas, two days later I turned it on, it ran for a minute and then the clean and the exclamation started flashing. I’ve cleaned everything, taken everything apart, checked wheels, checked for things stuck, it’s charged, turned it off, cleaned the sensors. I’ve tried everything basically I can think of and it still just runs for a minute and then those two lights flash red. Lost cause? Just wanted to make sure before I ordered a different one.
I was able to fix it. On mine there is a small rubber piece over a ball bearing on the end of the brush, and the rubber piece was wearing thin and causing the brush to get stuck. I removed the rubber piece and replaced it with a small thin circular magnet that fit in the area perfectly. I also used some DW40 on the other end of the brush that spins. It is working perfectly now.
I have a RV750 (UL E491422) but the bottom cover is a single piece which surrounds both drive wheels. It's currently not working (spot & dock flash together) likely because some cat hair has gotten tangled around the brush motor. I've tried to take it apart, but even with the screws removed the bottom cover won't budge. Any suggestions on what I might be missing? Maybe they glued it together?
Ok, mine is saying bumper is obstructed however it moves freely. But the ball and castor is so bound with dog hair and grit the wheel doesn’t spin easily the castor is ok but the wheel is gummed up. How do I pop out the wheel and castor assembly to clean it? I will be cleaning the sensors as recommended too
@@SmittysWorld I just took out the filter and the dust bin, cleaned the roller brush ect and made sure it was all empty. I replaced the filter with the extra one in the box and thats it. No chemicals not water or anything other than removing any debris
@@SmittysWorld the same thing happened to my RV720, The red clean light flashes red and when on the charger it beeps every 10 -15 seconds... Please help. Also when on the charger, if I press clean it will roll of the charger... Turn around and stop with the clean light flashing red 🚨. Help please!!!
750 with suction error, cleaned all filters and suction area as much as possible without taking apart. Reset and removed battery too. Still getting error within 3 seconds of running. Any advice?
Does it make a noise when running? The bearing at end of brush roller could be bad or the housing of the motor could have melted making the belt slip .
@@SmittysWorld , Hi thanks for replying. I disassembled the machine the belt looks great the motor turns easily I have no openings between word connects to the circuitboard to the motor I have continuity and both sides to there’s no open in the wire I’m not sure what to do next
@@michaelhabschmidt2153 need to get a power supply to test outside the unit. could be a issue with the motor or the motherboard rare but not impossible
Smitty, I do not know if you still look at comments on this but... My RV750 is giving the error "Something Interrupted the Robot's Cleaning, Please Check Underneath your robot to clear obstruction." I have cleaned it thoroughly but will not run but a min or so. Any Ideas?
Hey how’s it going I try my best to read most the comments don’t always get to them. This issue can be a few things but what I’ve seen a lot of times is a broken brush motor gear. Spin the brush by hand back and forth and see if you can feel it stop or hang up. Also can be the motor overloading. Then sometimes this error is a wheel issue but not often.
Brand new Shark ion with docking station trash container. Shark replaced it as the Blue light and Red light and wif lights were flashing. They went though a checklist and said keep it we will sned you a new one. Like I said, never used and would not boot up. COuld it be the motehr board??? can I fix it?? Do you buy them??? Thanks
Could be a motherboard issue could be a battery issue could be a connection anywhere if she’ll like there’s so many different things that could be I do buy them but generally I don’t spend a lot on him because I don’t know the issue and what parts are salvageable
Mine has a red exclamation point flashing along with the dock and max button. Customer service said I may need a new brush roll but the roll is pretty new and clean and my app just says obstruction and even something about the cliff sensors. My robot will only run about a minute before flashing these lights and because my robot is out dated and they no longer make the model they refused to help fix or figure out the problem..
I just started having the same problem! I just got mine for Christmas! My app says “motor suction” I have done everything and cleaned everything but it is still doing the same thing!
Same. Not very satisfied with Shark. Did anyone solve this? I've cleaned it so thoroughly that I think it might be a bad motor or something. Hard to believe that it's any dirt or hair.
Clean, dock and red error coming on. I havea shark robot. It tries to engage, goes a little bit then this happens. Brushes, sensors, clip center, wheels, filter deep cleaned. It sucks out at docking station. Has run once since doing this with really loud grinding noise, goes to same error. It doesn't give a code makes a duna-nuh-nuh noise.
I have an 750rv that my kid dropped a closed water bottle on. Now only the WiFi light is on and stays lit until turned off and seems almost purple? Lol, is unresponsive otherwise. Any ideas?
My sharkie robot leaves the docking station and then stops with the explanation mark flashing and won't go any farther, I've cleaned it and checked the sensors also, what else could be the issue
Thank you for the excellent video!!! Our daughters RV750_N started flashing both red CLEAN and blue DOCK buttons. I cleaned sensors and that didn’t clear it. What do you think is next?
My 750 has the red flashing exclamation point and the blue dock and max flashing as well. The error I get is that the brush-roll is stuck. I’ve checked and there is nothing there. Any suggestions?
@@dee0683 My Daughter’s is doing the same thing. Goes about 10’and then gets that combination of lights. I was hoping I could fix it for her. I guess not.
My issue is I have zero response from the robot but when I connect it to the dock it quickly flashes a calendar with a clock and then nothing. Won't charge won't turn on anything
I have cleaned everything to stop the "Clean" light from flashing. All the wheels are moving correctly. Could this be the battery? What is the cure for this problem.
Smitty - I've watched several of your UA-cam videos, and they are great! My problem is unusual; it is not a mechanical fix. A 16 x 20 picture dropped onto our RV750n and struck it right on the CLEAN button. Now that button is lit, but the Shark won't do anything. So, I think what I need is the top case for it. I haven't seen this addressed in any of your videos. Can you help?
Easy way to check is to take the robot apart like I do in other videos once the top case is off see if you can remove the buttons on the inside of the lid then see if the light is still lit up after words. I might have a case I can sell you
FOUND SOLUTION!! Read below Ok I have a RV750 and I looked everywhere for a solution to seems like the most common problem. Cleaning light turns red and red exclamation flashing.. telling me to remove blockage. I was about to give up after taking it apart and putting it back together. Lightbulb 💡 in my head turned on and it actually fixed the problem!!! Ok so what you do is take the dust bin off, inside you can see a plastic screen with 2 small screws take that off now get a shop vac or a house vacuum with an extension tool now put it in side the hole you see after removing the plastic screen, you will hear the motor running inside, it’s the vacuum your using suctioning out any dirt or trash inside. Did that a few times and believe me when I tell you it worked!!! I was going crazy thinking of everything and looking all over the Internet. Let me knowing it works for you!!! Saved me from buying another one 😓
RV750 Help!! Max light flashing, bumper stuck, when it takes a couple of bumps, it won’t move back away from the body of the shark. Up an down is fine on the bumper but when it gets pressed towards the shark, it stays. Can’t find any help on You Tube! My floors are depending on you!
Smitty, thanks so much for making these videos and all you good advice! You have helped me out a lot. I found a fried motherboard on my RV750_NR S6. Was wondering if a motherboard from an RV850 would swap in? Otherwise I'm in the market for a 750 motherboard. Thanks!
My system was two days old and I set it up to go somehow it got itself trapped and it keeps saying the clip sensors are tripped even though everything is spotless in the item is only 2 days old the clean and dark lights go into flashing and it will not work
@@nogood3232 No you should be able to just turn off turn it back on and it should start fine if it’s give me an issue like this or might be a factory problem with that so it’s best to take it back and just get another one
flashing together? Cliff sensors are reporting an error. Wipe cliff sensors with a clean cloth. Robot cannot start due to an error. Turn off the power switch on the side of the robot, wait five seconds, then turn power back on. Ensure your robot is on a level surface with no obstructions.
@@tabithahood5484 Wow talk to text messed up on that one. If playing in the sensors and fix the issue then it’s a sensor issue or a motherboard issue you can take it apart and see if maybe one wire is better there’s a burnt spot on the motherboard. But if it’s still giving you an error to reset and then everything and clean them then it’s probably gonna be a bigger issue.
@@SmittysWorld Thanks for the quick reply! That was my thought as well but after replacing it and being docked all night there was nothing. No lights. Maybe I received a bad battery. Any suggestions for where to purchase one? Admittedly, I got the last one from Amazon.
Hey, my shark vacuum starts, goes and then stops immediately. It gives me a red flashing exclamation point, red clean, blue dock and blue max flashing. Any idea what this could be?
Sameee I did everything...I don't know what to do
Hi! Smitty! I have an RV750R01US that is flashing red clean and flashing exclamation point. I’ve cleaned the sensors, cleaned the filter, made sure there wasn’t hair stuck, and it’s still evading me. What am I doing wrong?
Did you get it working? Mine is doing the same thing.
If you are missing a brush will it not work properly
will work fine unless your missing the main brush
I’ve got an RV765 and have only had it for a couple of months!
When i try to run the “max” light flashes, despite having emptied the vessel and cleaned the filters.
Any advice?
Mine too! I cant figure out why 😔
That’s the issue I came here hoping to remedy! Dust bin empty clean filters and sensors. Runs for a min then flashes Max and stops.
Same!
Where can I buy the boundary sensors? I have a Red exclamation point and red "Clean" indicators lit and the filter is new. Thanks
Hello Smitty,
Our robot vacuums for a while and just stops, clean is flashing red, and max is flashing blue?? What do you think our problem is ??
Same...any luck?
Hello, I have a Iq shark the code is a exclamation point red light it says suction low clean and empty bin I did all that it will start and go 3 seconds about then flash code again ,, what now do I need to replace somthing I did all the cleaning and all the simple stiff. Please help..thanks bless
Having issue with the red clean coming on an ! Flashing red Just after a few seconds of running this happens what could it be and how can I fix this???
Me to
What can I do with my Shark 750? One of my wheels stops turning so it just spins in a circle the shuts off
My shark 750 model robot runs @3 ' then stops with 2 flashing lights, 1 on the clean button, and 1 just left above the clean button. Please help. 3 days before this happened, it was making a loud noise for @ 2 -4 minutes then the noise went away.
I have the 750. It will clean for a couple minutes then just stop and the dock and spot lights flash blue. I check and there is nothing stuck anywhere. Even put all new brushes on and new filters. Any idea why?
Have you taken a air compressor and blown the inside of the suction motor and vents out?
I have a RV1100SRUS and I have a red battery light that flashes when I put on the charger and it won’t run could you tell me what is it I need to do?
I press the dock button an it goes into clean mode. Any idea how to fix that?
what model
Smitty I have a Shark RV750 with red exclamation point and Wi-Fi lights solid. Help?
My dock light (blue) and clean light (red) flash simultaneously when I hit the “clean” button on my remote. I clean the sensors and powered it off for five seconds. Turned it back on and this still occurs. Do you have any other ideas of what the issue could be?
Mine as well
Me too
Same
So i assuming nobody got an answer
Mine is flashing clean red and max blue. I’ve cleaned everything and the dust collector is definitely in there right. Help?
Mine is having the same issue did you get to resolve the problem??
Max blinks blue when I push anything any advice??
Hi! I have a RV761 and the Clean and ! Is flashing red. I have no clue what it means but I’ve already tried cleaning everything.
Could be the switch for the dust bin not fully engagin
I have the ion rv750, turned a year old at Christmas, two days later I turned it on, it ran for a minute and then the clean and the exclamation started flashing. I’ve cleaned everything, taken everything apart, checked wheels, checked for things stuck, it’s charged, turned it off, cleaned the sensors. I’ve tried everything basically I can think of and it still just runs for a minute and then those two lights flash red.
Lost cause? Just wanted to make sure before I ordered a different one.
I’m having the same problem with mine and I’ve cleaned everything and it still won’t work. Did you ever get yours to work?
I was able to fix it. On mine there is a small rubber piece over a ball bearing on the end of the brush, and the rubber piece was wearing thin and causing the brush to get stuck. I removed the rubber piece and replaced it with a small thin circular magnet that fit in the area perfectly. I also used some DW40 on the other end of the brush that spins. It is working perfectly now.
I have a RV761 the “MAX” button blinks blue after a minute of being on.
empty the part where the trash goes and make sure that compartment is in tight and properly
I have a RV750 (UL E491422) but the bottom cover is a single piece which surrounds both drive wheels. It's currently not working (spot & dock flash together) likely because some cat hair has gotten tangled around the brush motor. I've tried to take it apart, but even with the screws removed the bottom cover won't budge. Any suggestions on what I might be missing? Maybe they glued it together?
why is it missing the wheels and dustbin?
What dose it mean if the explanations mark is flashing?I have cleaned everything.It runs for a few seconds the stops and beeps.
what model
When charging it blinks 1 blue light, then all 3, then 1 blue light, then all 3. Does this mean it's not charging
Ok, mine is saying bumper is obstructed however it moves freely. But the ball and castor is so bound with dog hair and grit the wheel doesn’t spin easily the castor is ok but the wheel is gummed up. How do I pop out the wheel and castor assembly to clean it? I will be cleaning the sensors as recommended too
I cleaned my RV761 and ever since the suction motor keeps coding. Any suggestions?
That’s interesting when you say cleaned what did you use to clean it with and is there any chance something got down inside the suction motor?
@@SmittysWorld I just took out the filter and the dust bin, cleaned the roller brush ect and made sure it was all empty. I replaced the filter with the extra one in the box and thats it. No chemicals not water or anything other than removing any debris
@@SmittysWorld the same thing happened to my RV720, The red clean light flashes red and when on the charger it beeps every 10 -15 seconds... Please help. Also when on the charger, if I press clean it will roll of the charger... Turn around and stop with the clean light flashing red 🚨. Help please!!!
@@brandycollier2478 did you ever get it to work again???
This happened to mine, turning it off for a few mins fixed it
Help! 750- no lights but still "talking to me". It makes the sound that it's going to charge then gives me the error beep sound. 😩
750 with suction error, cleaned all filters and suction area as much as possible without taking apart. Reset and removed battery too. Still getting error within 3 seconds of running. Any advice?
The motor could be going bad, Or the motherboard has some issues.
Hi, what would you recommend to do if the main roller brush does not turn in the belt that drives it is good?
Does it make a noise when running? The bearing at end of brush roller could be bad or the housing of the motor could have melted making the belt slip .
@@SmittysWorld , Hi thanks for replying. I disassembled the machine the belt looks great the motor turns easily I have no openings between word connects to the circuitboard to the motor I have continuity and both sides to there’s no open in the wire I’m not sure what to do next
@@michaelhabschmidt2153 need to get a power supply to test outside the unit. could be a issue with the motor or the motherboard rare but not impossible
@@SmittysWorld Would you know what the voltage is for that electric motor?
Do you think Putting the battery directly to the electric motor?
@@michaelhabschmidt2153 should be 13-16 depending on model but 12 volts should be fine
I have this one but it says the tray much be inserted to clean but it’s in? How do I fix this
the switch at the back where the tray goes might be broken tape it down.
Smitty, I do not know if you still look at comments on this but... My RV750 is giving the error "Something Interrupted the Robot's Cleaning, Please Check Underneath your robot to clear obstruction."
I have cleaned it thoroughly but will not run but a min or so. Any Ideas?
Hey how’s it going I try my best to read most the comments don’t always get to them. This issue can be a few things but what I’ve seen a lot of times is a broken brush motor gear. Spin the brush by hand back and forth and see if you can feel it stop or hang up. Also can be the motor overloading. Then sometimes this error is a wheel issue but not often.
Brand new Shark ion with docking station trash container. Shark replaced it as the Blue light and Red light and wif lights were flashing. They went though a checklist and said keep it we will sned you a new one. Like I said, never used and would not boot up. COuld it be the motehr board??? can I fix it?? Do you buy them??? Thanks
Could be a motherboard issue could be a battery issue could be a connection anywhere if she’ll like there’s so many different things that could be I do buy them but generally I don’t spend a lot on him because I don’t know the issue and what parts are salvageable
Mine has a red exclamation point flashing along with the dock and max button. Customer service said I may need a new brush roll but the roll is pretty new and clean and my app just says obstruction and even something about the cliff sensors. My robot will only run about a minute before flashing these lights and because my robot is out dated and they no longer make the model they refused to help fix or figure out the problem..
I just started having the same problem! I just got mine for Christmas! My app says “motor suction” I have done everything and cleaned everything but it is still doing the same thing!
Same thing my daughter’s is doing.
Same
Same. Anyone find any solutions?
Same. Not very satisfied with Shark. Did anyone solve this? I've cleaned it so thoroughly that I think it might be a bad motor or something. Hard to believe that it's any dirt or hair.
Clean, dock and red error coming on. I havea shark robot. It tries to engage, goes a little bit then this happens. Brushes, sensors, clip center, wheels, filter deep cleaned. It sucks out at docking station. Has run once since doing this with really loud grinding noise, goes to same error. It doesn't give a code makes a duna-nuh-nuh noise.
I have an 750rv that my kid dropped a closed water bottle on. Now only the WiFi light is on and stays lit until turned off and seems almost purple? Lol, is unresponsive otherwise. Any ideas?
Take the top off see if there is any damage to the motherboard could just be a broken button under there
Rv750 battery indicator and signal indicator are both flashing????
Hmm could be a issue with motherboard or battery. Is it a yellow bottom robot
No it is not , it is saying it is in setup mode ???
My sharkie robot leaves the docking station and then stops with the explanation mark flashing and won't go any farther, I've cleaned it and checked the sensors also, what else could be the issue
I have a beep and flashing blue clean light but nothing else. Not even charging lights???
Hi mines flash 1 red bar...then flash 3x blue then stops...then nothing is lit no charge...whats wrong
Thank you for the excellent video!!! Our daughters RV750_N started flashing both red CLEAN and blue DOCK buttons. I cleaned sensors and that didn’t clear it. What do you think is next?
Was it out of the blue or did it run over something?
It was out of the blue.
@@michaelmitschsr.9412 One of the sensors went bad or is stuck thats odd all i can say is take apart and clean again
Do you think I should take the vacuum apart? I cleaned the sensors from the outside. How much is a set of new cliff sendors?
@@michaelmitschsr.9412 I don’t think it’s gonna be simple as a new sensor might be a motherboard issue or wire issue
My 750 has the red flashing exclamation point and the blue dock and max flashing as well. The error I get is that the brush-roll is stuck. I’ve checked and there is nothing there. Any suggestions?
I called Shark and all they offered was a 30% off for a new vacuum 😞
@@dee0683 My Daughter’s is doing the same thing. Goes about 10’and then gets that combination of lights. I was hoping I could fix it for her. I guess not.
My charging lights flash 1 bar, then all 3. Any ideas? It is fully charged and functions just fine.
Mine does the same thing. Also wondering why it does this.
My issue is I have zero response from the robot but when I connect it to the dock it quickly flashes a calendar with a clock and then nothing. Won't charge won't turn on anything
Did it just happen out of nowhere? Could be a bad battery.
I have cleaned everything to stop the "Clean" light from flashing. All the wheels are moving correctly. Could this be the battery? What is the cure for this problem.
That’s a hard question to answer to be honest. What model do you have?
what, what if theres a solid red exlamation mark on it
Depends on the model
it is the same as the video@@SmittysWorld
Smitty - I've watched several of your UA-cam videos, and they are great! My problem is unusual; it is not a mechanical fix. A 16 x 20 picture dropped onto our RV750n and struck it right on the CLEAN button. Now that button is lit, but the Shark won't do anything. So, I think what I need is the top case for it. I haven't seen this addressed in any of your videos. Can you help?
Easy way to check is to take the robot apart like I do in other videos once the top case is off see if you can remove the buttons on the inside of the lid then see if the light is still lit up after words. I might have a case I can sell you
FOUND SOLUTION!! Read below
Ok I have a RV750 and I looked everywhere for a solution to seems like the most common problem. Cleaning light turns red and red exclamation flashing.. telling me to remove blockage. I was about to give up after taking it apart and putting it back together. Lightbulb 💡 in my head turned on and it actually fixed the problem!!! Ok so what you do is take the dust bin off, inside you can see a plastic screen with 2 small screws take that off now get a shop vac or a house vacuum with an extension tool now put it in side the hole you see after removing the plastic screen, you will hear the motor running inside, it’s the vacuum your using suctioning out any dirt or trash inside. Did that a few times and believe me when I tell you it worked!!! I was going crazy thinking of everything and looking all over the Internet. Let me knowing it works for you!!! Saved me from buying another one 😓
Thank you, it worked!!
Yesss it actually works!! Thanks a lot!!! I was goin' crazy too 😅
My robot won’t turn on when on charging dock or plugged in only the WiFi light lights up blue and red.
It kept stopping with the Max light comes on. However, the duct collector is empty!
What mode;
@@SmittysWorld I figured it out! It turned out it was one of the spinning brushes was restricted by hairball.
Mine is doing it in the clean mode. Empty bin and clean filters.
All my lights are flashing. Plus it shows a ! Mark on top left
I have a 750 with a red flashing light i have cleaned everything and replaced the battery
I’ve pulled mine apart. Cleaned filter and brushes, cleaned sensors, made sure nothing in bumper. Still blinking red clean
RV750 Help!! Max light flashing, bumper stuck, when it takes a couple of bumps, it won’t move back away from the body of the shark. Up an down is fine on the bumper but when it gets pressed towards the shark, it stays. Can’t find any help on You Tube! My floors are depending on you!
Gonna have to take the front bumper off five t6 torx screws on bottom comes off check see what spring is sticking and if you can clean it.
@@SmittysWorld thanks! I’ll try this
Smitty, thanks so much for making these videos and all you good advice! You have helped me out a lot. I found a fried motherboard on my RV750_NR S6. Was wondering if a motherboard from an RV850 would swap in? Otherwise I'm in the market for a 750 motherboard. Thanks!
No they are a little different and I don’t have any boards anymore
@@SmittysWorld ok thanks I really appreciate the reply. You are a big help thanks again
@@SmittysWorld
Help mine is blinking read light
I have cleaned everything
Please help :)
Thank you
My system was two days old and I set it up to go somehow it got itself trapped and it keeps saying the clip sensors are tripped even though everything is spotless in the item is only 2 days old the clean and dark lights go into flashing and it will not work
If you’re robots only two days Old you need to take it back to the store and get another one
@@SmittysWorld okay it was a birthday gift have to see if I could get my grandmother to find the receipt I was hoping I was just doing something wrong
@@nogood3232 No you should be able to just turn off turn it back on and it should start fine if it’s give me an issue like this or might be a factory problem with that so it’s best to take it back and just get another one
@@SmittysWorld ty I will find out this week. Keep making these informative videos they help out people
Mine is saying clean light flashing red and ! Is flashing red
what model
So I have the Dock light (blue) and clean (red) flashing. Maybe I missed that in your video
flashing together?
Cliff sensors are reporting an error.
Wipe cliff sensors with a clean cloth.
Robot cannot start due to an error. Turn off the power switch on the side
of the robot, wait five seconds, then turn power back on. Ensure your
robot is on a level surface with no obstructions.
Shark ion v750. Touch clean button. Moves from station turns and stops.
Any errors or does it die
No errors. After moves from station clean button stays on. Just sits there.
@@lisaritter535 hmm that’s interesting 🤔 will it go home from there
No. It will not move. I pickup and put on charger. And clean button goes off.
@@lisaritter535 that could be a ton on things I’d say motherboard over anything else tho
Error 21 everytime I turn mine on. It tells me to reboot it immediately
Motherboard error
@@SmittysWorld fixable?
Cleaned cliff sensors but still flashes red clean
Under the sun just got a win better I could be a motherboard issue
@@SmittysWorld ?
@@tabithahood5484 Wow talk to text messed up on that one. If playing in the sensors and fix the issue then it’s a sensor issue or a motherboard issue you can take it apart and see if maybe one wire is better there’s a burnt spot on the motherboard. But if it’s still giving you an error to reset and then everything and clean them then it’s probably gonna be a bigger issue.
My robot light problem no charge
My shark stops in the middle of the room, fully charged and all of the blue lights are flashing.
Hey damn it. I'm Smitty? lol Actually there are many. All Smith's are Smitty's.
Haha hell yes
720 flashing clean and red after 10 second
Mine has clean light and max light flashing and will not work. All the brushes work and it has been emptied. Any ideas?
My blue lights are flashing when docked as if it were charging but it never reaches a charge. Any ideas?
Battery probably is bad
@@SmittysWorld Thanks for the quick reply! That was my thought as well but after replacing it and being docked all night there was nothing. No lights. Maybe I received a bad battery. Any suggestions for where to purchase one? Admittedly, I got the last one from Amazon.