Where is the speaker that makes its various operation sounds? When mine is charging it constantly makes a bunch of random beeping noises (while Im trying to sleep) so I want to remove the part of the mother board that is making those noises.
Thanks. Was able to get down to the belt and clean all the hair out and stop the squeaking noise that started yesterday. Deep cleaned everything. Looks good as new.
Do you have a video on how to fix the sweeper arms? I am getting an error message that’s says debris is blocking the function. But I’ve cleaned everything out and the only thing I can find is that one of the arms seems a lot tighter than the other. I tried to pull the whole thing apart but can’t figure out how to get inside the arm motors to see what’s wrong.
I feel like ive tried everything from your videos but can't figure out what's wrong. I am getting the flashing red clean with flashing red ! error on my RV720. I got my first one in 2018, and this error happened within 6 months so it was replaced. Now the replacement has lasted me 2 years and same issue again. New filter, took everything I could apart and cleaned it, etc. It will go for about 2 seconds and then stop and display the error
Thanks for the video. I have ion 850 and looks like I need a motor after watching. I think I need to get all the way to opening the motor casing still but hoping you might have the part?
I need a new wire harness going from the one wheel to the motherboard, do you have that by chance, I put the wheel back into place and broke a few wires because they were crimped from my mistake
Thank you for the help with my 720 iRobot. Installed a new brush motor, the unit ran nicely for 3 minutes and then made the same grinding noise as before. Brush roller not spinning. Suggestions?
Garth H. McDonald no sorry I don’t offer repair services. Have you taken the motor out by chance? If you have you can get a 12 volt battery and test the motor to see if it spins
What would somebody sell a vacuum for that needs the suction motor replaced? I need to sell one as I am not going to have the time to dig into it like I’d hoped
Should fit right in unless you ordered the wrong one compare it to the other one and make sure the square head that the brush goes on is turned correctly
I suspect the one I got is a bit bigger. I could not make it fit. Is it possible to switch the motor in the old assembly with the Motor in the new one? I had it apart once but I can’t remember if the motor can come out.
I didn't shut down my shark before I flipped over to clean the vaccum. Now it won't move more than a few inches from base with a cliff error. What can I do
Hoping you can help me. Have a RV750 that will go for 1 sec then stop. The notification says it’s a suction issue but it will work in Eco mode just not in anything higher. It’s not the filters as I’ve taken those out just in case. Shark says I need to get a new one but this thing is only 15 months old
Hey man, question... hopefully u can give me a quick fix answer. Can I just post it here or email u or what? I know you don’t exactly want to get into iMessage repair service or anything. I feel like I can fix most anything but sometimes troubleshooting can be the most difficult part. I have a Shark iON RV852WVQPR (so is that an 850??) anyway. Was making a horrible scrubbing noise and I had no clue what it was. I checked for this colorization around the casing for the motor and on the bottom of the channel under the bristles. I pulled both wheels and there was no entanglement or anything there. Everything seems to rotate without restriction. It is clean. SO, I discovered that when I remove the rotating cleaning bristle the robot operates perfectly fine with no noises or scrubbing. I replaced the bristle roller and the outer retaining case/clip thing I just started scrubbing again. So I tried it but just placing the roller inside and gently setting it on the floor WITHOUT the retention clip part. It works perfect. No issues except for the fact that there’s no way the bristle is sitting in there correctly and I feel like if it gets tangled on anything it’s just going to pull it out. Why would that retention clip because in the excessive scrubbing noise. Help man PLEASE
Brad Ball without the clip installed the brush doesn’t have tension on it so when it spins it works fine try running it on carpet without more then likely will make the noise could still be a bad brush motor or belt. But the clip could be worn out as well could try some Grease on it .
Excellent. It’s going to be slow for me since I have to position the screws so I know where they go. Looks like you’ve done enough you could do it with your eyes shut. How do I order the motor. Or who can I order it from.
Can you help me my shark vacuum has an error popping up it says : red Clean plus Red ! Exclamation. Do you know what means ? Please advise . Thank you 🙏 I enjoy your videos
I have ashark IQ Robot. It keeps stopping with an error 3 message. I look underneath and one of the side brushes doesn't spin, and one of them spins easily. How do I fix the stuck brush?
Love your detail break downs on the sharks matter effect I brought one last week which was broken keep your finger cross that I am able to fix it myself by the way.whats ur email or ebay company name just in case I can buy parts from you thanx Big guy & God bless
Where is the speaker that makes its various operation sounds? When mine is charging it constantly makes a bunch of random beeping noises (while Im trying to sleep) so I want to remove the part of the mother board that is making those noises.
I have a Shark IQ self empty. Brush roll won’t activate when vacuum running. New brush roll motor needed?
Thanks. Was able to get down to the belt and clean all the hair out and stop the squeaking noise that started yesterday. Deep cleaned everything. Looks good as new.
Thank you for the tutorial! I was able to fix my vacuum and replace the brush motor.
Hey there, any chance I can buy a replacement motor for my Shark AV2501S?
Do you have a video on how to fix the sweeper arms? I am getting an error message that’s says debris is blocking the function. But I’ve cleaned everything out and the only thing I can find is that one of the arms seems a lot tighter than the other. I tried to pull the whole thing apart but can’t figure out how to get inside the arm motors to see what’s wrong.
what model
I need a spinner left spinner motor for a RV 1001, will other model motors work?
No they are different message me on eBay I’ll get you the link for the correct ine
One
I have an rv760 series the part that turns the brushroll is seized up do you know where I can get another one
My shark only shows a red battery light, I was wondering if you could help me out,it won't even come on it all.
I feel like ive tried everything from your videos but can't figure out what's wrong. I am getting the flashing red clean with flashing red ! error on my RV720. I got my first one in 2018, and this error happened within 6 months so it was replaced. Now the replacement has lasted me 2 years and same issue again. New filter, took everything I could apart and cleaned it, etc. It will go for about 2 seconds and then stop and display the error
Thanks for the video. I have ion 850 and looks like I need a motor after watching. I think I need to get all the way to opening the motor casing still but hoping you might have the part?
I need a new wire harness going from the one wheel to the motherboard, do you have that by chance, I put the wheel back into place and broke a few wires because they were crimped from my mistake
I have a 750
@@jasonbice4815 www.ebay.com/itm/175415255958?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=45UvfEQjQN6&sssrc=2349624&ssuid=45UvfEQjQN6&var=&widget_ver=artemis&media=COPY
www.ebay.com/itm/175415255958?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=45UvfEQjQN6&sssrc=2349624&ssuid=45UvfEQjQN6&var=&widget_ver=artemis&media=COPY
Thank you for the help with my 720 iRobot. Installed a new brush motor, the unit ran nicely for 3 minutes and then made the same grinding noise as before. Brush roller not spinning. Suggestions?
remove motor assembly check gears.
Do you know how to fix the suction motor error on a RV750_N
Garth H. McDonald clean it out if that doesn’t work it’s either new suction motor time or motherboard time
Smitty's World thats was quick! Cleaned out, do you do repairs?
Garth H. McDonald no sorry I don’t offer repair services. Have you taken the motor out by chance? If you have you can get a 12 volt battery and test the motor to see if it spins
Smitty's World not yet, just got it but figured it never hurts to ask. Thanks for the advice!
Garth H. McDonald I completely understand
What would somebody sell a vacuum for that needs the suction motor replaced? I need to sell one as I am not going to have the time to dig into it like I’d hoped
Is there a secret to getting the brush motor back in? Could I have the wrong part?
Should fit right in unless you ordered the wrong one compare it to the other one and make sure the square head that the brush goes on is turned correctly
I suspect the one I got is a bit bigger. I could not make it fit. Is it possible to switch the motor in the old assembly with the Motor in the new one? I had it apart once but I can’t remember if the motor can come out.
@@JJKOFROTH yes you can swap just the motors
I didn't shut down my shark before I flipped over to clean the vaccum. Now it won't move more than a few inches from base with a cliff error. What can I do
Pull battery leave for a hour should reset
Thank you for trying but same problem. Error #7 cliff
Life saver!! Thanks so much!! Replaced my motor.
Where do the 4 silver colored screws go. I forgot where I took them out?
Depends which ones your talking about. Motherboard has some , brush drives have some , suction motor has some.
I found holes for all of them and it is working again.
Thanks for your advice
.
@@JJKOFROTH AWESOME TO HEAR!!!! Glad I could Help
Hoping you can help me. Have a RV750 that will go for 1 sec then stop. The notification says it’s a suction issue but it will work in Eco mode just not in anything higher. It’s not the filters as I’ve taken those out just in case. Shark says I need to get a new one but this thing is only 15 months old
Sounds like it could be a processor board on the suction motor or the motherboard itself
Help I spilled my coffee on mine and it's not working!!!! Idk what to do
Looking for a new belt for the the brush
Mine won’t suck things up no more ?
suction motor is bad
I had same like this one had an issue that when I turn it one it will work and then it will stop
Hey man, question... hopefully u can give me a quick fix answer. Can I just post it here or email u or what? I know you don’t exactly want to get into iMessage repair service or anything. I feel like I can fix most anything but sometimes troubleshooting can be the most difficult part. I have a Shark iON RV852WVQPR (so is that an 850??) anyway. Was making a horrible scrubbing noise and I had no clue what it was. I checked for this colorization around the casing for the motor and on the bottom of the channel under the bristles. I pulled both wheels and there was no entanglement or anything there. Everything seems to rotate without restriction. It is clean. SO, I discovered that when I remove the rotating cleaning bristle the robot operates perfectly fine with no noises or scrubbing. I replaced the bristle roller and the outer retaining case/clip thing I just started scrubbing again. So I tried it but just placing the roller inside and gently setting it on the floor WITHOUT the retention clip part. It works perfect. No issues except for the fact that there’s no way the bristle is sitting in there correctly and I feel like if it gets tangled on anything it’s just going to pull it out. Why would that retention clip because in the excessive scrubbing noise. Help man PLEASE
Brad Ball without the clip installed the brush doesn’t have tension on it so when it spins it works fine try running it on carpet without more then likely will make the noise could still be a bad brush motor or belt. But the clip could be worn out as well could try some Grease on it .
Excellent. It’s going to be slow for me since I have to position the screws so I know where they go. Looks like you’ve done enough you could do it with your eyes shut. How do I order the motor. Or who can I order it from.
email me i stopped selling on ebay
Can you help me my shark vacuum has an error popping up it says : red Clean plus Red ! Exclamation. Do you know what means ? Please advise . Thank you 🙏 I enjoy your videos
Heyy, can you repair mine if I’m in Canada?
I have ashark IQ Robot. It keeps stopping with an error 3 message. I look underneath and one of the side brushes doesn't spin, and one of them spins easily. How do I fix the stuck brush?
Take robot apart remove the motor take it apart and see if something is clogging it up or if a motor went bad
Hey, how about i send you mine and you fix it?
Love your detail break downs on the sharks matter effect I brought one last week which was broken keep your finger cross that I am able to fix it myself by the way.whats ur email or ebay company name just in case I can buy parts from you thanx Big guy & God bless
Mine has pet hair caught in that main roller that turn it hopefully this will help it’s not sucking ! Lol
Getting a 6 error after getting wet