This is just the video I needed to fix my friend's motorised head - his attachment had exactly the same issue as you show here. I just wanted to say thank you for a very helpful video.
The end of the brush where it goes into the gear was locked up on mine. Couldn't figure out how to get the brush out until I watched this video. I was able to clean out the gunk and melted plastic so it could spin again. Thanks!
Good video thank you.......! Note: I think this is a design flaw on Dyson's part. It should be replaced by the manufacturer under warranty. Most people, seniors etc. will not be able to conduct this repair. Melting plastic of the parts can not possibly be a part of the design..... At least Dyson could replace the gear mechanism under warranty. Doesn't make sense that this problem is the customer's responsibility. Just my humble opinion. Thanks for your video.
@@techfixPOVbro can you pls help .. my Dyson hp04 Air fan is showing a white screen after I connected it to app it suddenly stopped when I turned it on again it's showing a white display that blinks over and over .
Hey TechhFix, I have exactly the same Mini Motorized Brush but the time belt is broken. Do you have any tips, where I can order a new and right one? Or can you tell the articlenumber of the timebelt? Mine is not longer readable. Thank you in advance.
Thanks a lot for the vid. Funny thing is I looked this up because i was unable to open mine - turned out in my case the big wheel fused to the cover! It turned out that the plastic frame holding the wheel even broke from the strain of it being fused. I swear this shit is made to break eventually :
My problem is that not only does the brush not turn but I can’t even get it out. I have the little cap off, but can’t get the brush to come loose, even pulling with a vice grips. I have the belt off but can’t go any further without getting at that last screw, since the brush won’t come out. Any suggestions?
It seems that due to the friction, some components melted and got stuck. I don't think you can separate the central brush except by forced separation. I had a similar situation and the only option was to use a big flat screwdriver as a lever to move the brush away. Good luck!
@@techfixPOV Thank you. My son did finally manage to get it apart, using force. And then he glued the piece that broke. :) But it works fine now. I’ll clean it more often after this. ;) $50 saved!
My issue is that the motor is not spinning at all… my guess is that one of the connectors might be loose, but I don’t know how to reach the back of the motor
Release the wires from the upper side, connect them to motor, tie them with small rope and while placing motor to its place, pull cables up and fit to housing
Try to switch the button on the brush several times while the brush is working. If it does not show any sign that it lights up, it is possible that the problem is with: the laser diode, the voltage regulator, the laser diode current control module. I will try to disassemble such a brush and I will return with a link here.
@@techfixPOV The laser light has not been on since the first day I bought it. I have set the button many times, but no result. Dyson sent me a new one. the broken sweeper remained with me. Thanks for ansvers.
This is just the video I needed to fix my friend's motorised head - his attachment had exactly the same issue as you show here. I just wanted to say thank you for a very helpful video.
Glad it helped
I had exactly the same problem. Your video shows the right hints and helped me to solve it. Thank you!!!
You're welcome!
The melted part was so hard. I put in hot water 3-4 times. I use its blue brush for apart it, thats more easy. Thanks for the video
Glad it helped!
Thanks for the vid. Had the same problem and with the help of you, I could fix the problem
Glad it helped
Worked like a charm. Weak craftsmanship, vac head had only been used a couple of times.. Easy fix. Thanks for the video
I'm glad it was helpful.
The end of the brush where it goes into the gear was locked up on mine. Couldn't figure out how to get the brush out until I watched this video. I was able to clean out the gunk and melted plastic so it could spin again. Thanks!
Glad I could help!
Good video thank you.......! Note: I think this is a design flaw on Dyson's part. It should be replaced by the manufacturer
under warranty. Most people, seniors etc. will not be able to conduct this repair. Melting plastic of the parts can not possibly be a part of the design..... At least Dyson could replace the gear mechanism under warranty. Doesn't make sense that this
problem is the customer's responsibility. Just my humble opinion. Thanks for your video.
It works! That part was melted maybe because I used the Max suction for too long. Thank you 😊
Glad it helped!
@@techfixPOVbro can you pls help .. my Dyson hp04 Air fan is showing a white screen after I connected it to app it suddenly stopped when I turned it on again it's showing a white display that blinks over and over .
Superb video … thank You! 🏁🏁
Glad you liked it!
Hey TechhFix, I have exactly the same Mini Motorized Brush but the time belt is broken. Do you have any tips, where I can order a new and right one? Or can you tell the articlenumber of the timebelt? Mine is not longer readable. Thank you in advance.
Thanks for teaching me how not to fix it.
Glad to help
Спасибо, помогло не сломать щётку😊
Glad it helped!
thanks for this video, the Vacuum Cleaner Drive Belt is gone in mine, the serial number have faded. Is it pioneer rubber belt 134-2m?
Yes, exactly this type of belt is mounted on the brush.
Thanks this helped a lot
Glad it helped
Thanks a lot for the vid. Funny thing is I looked this up because i was unable to open mine - turned out in my case the big wheel fused to the cover! It turned out that the plastic frame holding the wheel even broke from the strain of it being fused. I swear this shit is made to break eventually :
I had a similar situation, I know what you mean. It's only a matter of time before problems appear.
Thank you !
You're welcome!
Tyvm... Fixed ❤
Glad it helped
Thanks, it helped 💪
Glad to hear it!
good vid but shame not showing the removal of the large cog wheel as I need to replace the whole plastic part as that is what has broken.
My problem is that not only does the brush not turn but I can’t even get it out. I have the little cap off, but can’t get the brush to come loose, even pulling with a vice grips. I have the belt off but can’t go any further without getting at that last screw, since the brush won’t come out. Any suggestions?
It seems that due to the friction, some components melted and got stuck. I don't think you can separate the central brush except by forced separation. I had a similar situation and the only option was to use a big flat screwdriver as a lever to move the brush away. Good luck!
@@techfixPOV Thank you. My son did finally manage to get it apart, using force. And then he glued the piece that broke. :) But it works fine now. I’ll clean it more often after this. ;) $50 saved!
what screw bit are you using for the screws?
Torx T8 screwdriver
My issue is that the motor is not spinning at all… my guess is that one of the connectors might be loose, but I don’t know how to reach the back of the motor
The assembly containing the mechanism must be completely dismantled. The whole mechanism is fixed to the motor with two screws.
I removed the motor. Now i cant attached it back as the wire is deep in the holder
Release the wires from the upper side, connect them to motor, tie them with small rope and while placing motor to its place, pull cables up and fit to housing
@@ozelmert seems like motor is not working anymore
My dyson laser not working.
I haven't worked on a laser brush yet, but if you tell me what the problem is, maybe I can help you. Does the brush not spin? Does the laser work?
@@techfixPOV only the laser light is not working. From day one.
Try to switch the button on the brush several times while the brush is working. If it does not show any sign that it lights up, it is possible that the problem is with: the laser diode, the voltage regulator, the laser diode current control module. I will try to disassemble such a brush and I will return with a link here.
@@techfixPOV The laser light has not been on since the first day I bought it.
I have set the button many times, but no result. Dyson sent me a new one. the broken sweeper remained with me. Thanks for ansvers.