Відео

January 2025. Thanks, just completed the replacement in 90 minutes following this. No problem, and my Dyson V10 didn’t have the silicon protection on the board. The plastic trigger was broken in such a way it prevented a direct pull-out, so I had to break and prise it out through the trigger hole. Replaced with a steel version, a little smear of Vaseline helped get the new trigger over the pins.

What should I do if a red light comes on when I use a magnet?

Today, i washed mine and drying now. I saw that a gasket around 7 pound. I hope you make a video about only changing gasket.

Grazie x aver condiviso 😉👍💯

Soldering is a horrible fix. The copper wires will work harden and break at the solder joint. Only a new wire or a mechanical splice (butt connector, twist wires etc) will truly fix it. It WILL break again.

Can you tell me what’s those wire function, I already sent to Dyson and repaired, so the motor Dyson says broken is at my home, I want to test it,because I think it isn’t broken,I know the power pin,but I do not know what’s the red and white wire, I need a teacher!

Thanks bro!!!!!!! DIY forever!!

This still works.

We opened our Xiaomi vacuum cleaner and discovered its poor design, especially the internal filter for the fan that discharges air to the outside, as it was made in a way that ensures that the motor malfunctions after a measured period and thus leads to damage to the main board.

Comprehensive video but the music is annoying

Merci beaucoup 🙏

Could you list the tools needed for this? I'll probably need to buy a couple of them. Thanks!

This is a joke , had many hoovers in my life , but to spend over 200 pounds on this one and fix like that i crazy , i just scrap mine and buy new one , never dyson again

How do you replace the blue hose on the Dyson V15 laser cleaning head? I can't find a replacement hose for the laser head or any videos or instructions on how to do it. It's frustrating.

What a goat !

hi where you located

The old trigger piece did not look bad but the pivot holes were worn and elongated a very little bit, but it fixed the problem. Can't believe it was designed to be so critical..

I have the Dyson 7 animal. My bar will spin freely so I know the shaft is not stuck. It will not spin when powered though. The Minnie head works fine though. Do you know want the issue is? Some say to clean all electrical ports going back to the main vacuum motor. But if the Minnie will spin and work fine could that be the issue?

Thanks but I know because I’m here to remember that for my hp04

Fantastic teardown. Really helped me clean mine. Thank you. ❤

Where can I buy one new motor from ?

Merci beaucoup pour ce tuto ! Il m'a bien aidé à changer la gâchette de mon V10 ! 👍👍👍👍👍👍👍

I’m interested in seeing the part where you take the gold plastic piece off the motor body there’s some purple foam in between the two gold pieces. How do I repair that purple foam seal? Mine is deteriorating and I could feel air blowing through. You skipped that part in your video.

Muchas gracias por tu video, ha sido de gran ayuda. Saludos desde España

Je. l'ai acheté il y'a deux ans une fois la garantie passée ce lui ci tombe en panne ,ça réparation coûte un bras et bien entendu son prix d'achat aussi un conseil passez votre chemin .il est excessivement cher, vous allez payer juste la marque et cerise sur le gâteau il aspire moyen. rien de phénoménal !

First of all, I apologize for my poor English. I have a similar problem with my V15. It works like this and then stops, but after doing this 3-4 times, it continues to work without any problems. Then I stop the machine again and take a 1-minute break and it works without any problems again. But if I take a 15-20-minute break and do not start the machine, it starts to have the same problem again. So I think the machine returns to normal after working and warming up a little. If we take a break and let the machine cool down, the problem starts again. What do you think could be the source of this problem? I have been researching for 1 year but I could not find a solution.

Hello. Could you please make a video how to fix the Dyson v11 motor that turn on 1 second then stops ? ( motor issue not pcb board issue)

Hello, Could you help me? I have a similar problem with Dyson v10, that the motor does not turn because there is no power, how could I check that it is the mosfet that is failing

Podrias ayudarme? tengo un problema similar con Dyson v10 animal, que el motor no gira porque no llega alimentación, como podria comprobar que sea el mosfet lo que esta fallando

Wow! You are a genius. My vac smells like a wet dog. The smell is coming from the metal screen on my Dyson 15. I’m quite shocked that all the dust gets so deep into the vacuum.

Hi , great video. I fixed it follow yours instructions!!! Perfect. At the end i realized that one screw is bigger than others and if i try to screwing didnt ends!!! Do you remenber where screwing this screw? ( a little bigger from others)

Mines going on the bin. Just buying a new one 🤷🏼‍♂️

Nice video!!!! Do you know how it looks in Dyson the positive negative pole of the battery? I want to test one but I don’t have a battery with me I was going to improvise but I don’t want to spoil it

Hi. Your guide is really helpful! However, the problem of my Dyson is one(out of 3) of the gears is stuck and doesn’t spin. It is stuck inside the tube. Other 2 fell off when I removed the motor. In your video, the issue is the motor. But mine is gear inside the tube. I tried removing the the Circlip hoping to remove the bearing and safely remove the small gear but it didn’t help. It’s difficult to forcefully remove the gear by hooking or pliers as it may damage the teeth of the gear. Can you please help and advise?

genial ton tuto ❤❤ merci

Thank you very much! I just saved around 100€ and also did maybe a small environmental deed

You are great man

Please , what is the thing wich the filter contact it to inform that the filter is on ? can we do this thing or capter off or on position to let think the motor that the filter is on even we don’t put the filter ? Where is the sensor of filter please ?

Have a same problem, this button just stuck inside... Never bought Dyson again! But my wife loves it 🙆 Don't know what to do.. throw this hoover out or my wife 🤔😂.

thanks for sharing! what is the sensor called and where did you buy it?

Good job making the music annoying af

Hi. I have an s10. I checked two smd parts that have a zigzag resistor symbol. They are open. Would they be thermal fuses I can short over with wire? Leds on board light up briefly on power press but then go out.

👏👏👏 best repair Video, thank you👏👏

We had some, the best I can describe it is gunk, in the receptacle. So tried to do the smart thing and clean it out in the sink. I think I got some water in the circuit/battery area. This video saved me from having to get another one as I disassembled then used a hair dryer on warm for a minute or so. Had a couple of drops come out that would’ve never happened without your video. Reassembled and it works great. So had a slightly different problem but your video was great. Thank you!

LOL… would I go that far for a deep clean? Think the water is too deep 4 me. Great video 🎉🎉🎉

Hey, where did you know that you have to change only one Hall Sensor? Did you test them before? How?

Mine was stopping during use, found out that the fitting holding the brush in center was broken and loose. Everytime the brush hit a bump the motor would cut off due to the extra resistance. Ordered a new «end piece» (the opposite site from the motor) from temu. Fixed😃

Thanks for this video, very clear, did the job and saved me $, much appreciated

Thank you so much.. orderer the piece from amazon 9euro.. hard to dissemble and reassemble but very very well explained and showed. Be gentle and sort every screw different from the other. Thanks for saving me 200euro:)

This worked on my v12, exact same oroblem, thank you so much, now to dind a new screen...