You guys are the first big detailing company I ever stumbled on - love your products. Thanks for giving me the confidence to fix my most recent coating high spots.
I like this video, as it applies to any brand of coating, and any brand of polish, rather than specifically naming particular products as a promo for Adam’s products. I really appreciate that. 🚗🙂👍
You saved my bacon fella Applied my first attempt at ceramic coating yesterday to fully prepared Jaguar XJ Could believe how difficult it was given minimal instructions etc Loads of dark high spots in the panels Left one side alone luckily Came in searching for solutions came across your straightforward video exactly what I needed Got up early next day and polished out all panels and got rid of the blemishes Will now have to pluck up courage to try again! Thanks 😅
I did the same thing but not on the whole car. I was able to hand polish with microfiber applicator and level the coating without getting rid of it. It is still there but I caught it before 24 hours passed
Am just finishing up my own DIY applying Adam's Graphene Ceramic Coating (original formula, not advanced), and there were a couple unexpected things I ran into, partly because I did mine outside and not under artificial light. First, I was surprised that my prep resulted in a kind of dull, almost satin finish before applying the coating. Was happy to see that applying the coating restored the "shiny, wet" look. Working outside, I found that I couldn't see the coating flash due to lighting conditions. I then resorted to simply estimating by time, knowing from various videos to expect flashing to occur up to 2 minutes, so manually timed myself (estimation) and produced a fairly good result. But, as one might expect, there were some intermittent problems. I'd check back again in about 3-5 hours and see the cross hatches of my application in a combination of different angle and different light (again, this was outside). I was able to simply add another layer of coating and the problem was resolved. One patch in particular wasn't discovered until about 12 hours later and still was fixed by simply adding a new coat. All things considered, am happy with results to this point. Shortly after full curing, I'm then hopeful that I'll really get 7 years of outside protection from the sun!
Had the same challenge as you in not having a well-lit garage. One other tip they mention in another video is to go off of feel. Once the solution starts to feel tacky/sticky, it’s pretty well-cured. Time that, and you can sort of go off of feel.
After you use an abrasive shouldn’t you use surface prep to ensure any solvents left behind are removed from the surface before you reapply the ceramic coating?
Great video... Wish I would have known this before my first Adams ceramic coating🥴 But no worries...I figured them out...had good success with Sonax perf. Finish & microfiber applicator pad...some light hand polishing took care of the high spots and the UV light helps tremendously to check coverage & for high spots...👏👏👍👍
In my training, we were taught to before the ceramic coating, to wipe the surface with a panel wipe. We used Gyeon, then a ceramic prep spray, then the ceramic coating was applied.
I have a new car on the way...and have your kit. Knowing there are ways I can fix any mistakes I make gives me so much more confidence to do this for my very first time. Thanks for your great how to videos. I have some polish on the way too...just in case I have to make corrections before and after!
Please remind viewers to also IPA wipe down after any polishing and before reapplying new coating. Oils left behind from polish will preventive coating from properly curing and diminish its protective properties.
How to remove ceramic coating from camera lens? I coated my tesla and didn’t properly remove/level it from edges of the camera lens and now edges are showing blurry on the screen. I used the Adams graphene ceramic coating advanced and it's been around 36 hrs at the time of posting this. Appreciate your help.
I used the graphene kit as instructed and had awesome results. I did get a little over ambitious covering too much area all at the same time and some of the ceramic coating did begin to set up before I could polish it off. I used a plush towel with the boost spray and it evened out beautifully. On my black and chrome road king the ceramic coating makes the bike appear brand new. Great products from Adam’s! 👍🏻
By the way.. when you say “Cure”, what you really mean is “Flash”. Ceramic coat’s “flash time” is typically when it ready to wipe off (typically second to minutes) vs “cure time” is when the ceramic coating hardens and is safe to be driven (typically 2/3 days and up to a week sometimes to be fully cured).
So, the liquid Ceramic Spray can be used as a leveling agent within 2 hours? Let's say you let it flash, but you're having a hard time seeing the rainbowing before you wipe, can you spray a dusting of the Ceramic Spray before doing the final wipe to avoid high spots?
it was ok because they created an additional 'back link' to their website using google's youtube app. Backlinks are a top way marketers ensure their site has high SEO rankings so that said marketer's target search terms people use when they search google shows up in this case Adams' website in the first few results of the user's search results.
@@barbaroacosta5335 it’s not ok to do so. The bond in that spot is going to be weaker. But installers won’t redo a whole panels. So this video is more with fixing a mistake on high spots. I don’t ceramic my own cars. A good 4 times a year of a paint sealant and wax is cheaper than 1200+ ceramic coating. Plus you have to pay to maintain that coating. From washes and spray wax. To reapplying. Cause you can get tar or rough spots from contaminates where you will clay the car again. As a professional detailer to a customer. My advice is don’t put faith in ceramic coating. It’s pretty hyped up and not worth the cost.
Tried to coat my new painted trim pieces for my car but I ended up having a lot of noticeable "brush strokes" if you will when I took them outside in the sun. Tried to rehydrate but could not replicate these results. The coating was only on the pieces for about 45min to an hour when I tried this. 🤷♂️
Hello, thank you for the video. Question, I had a graphene coating (Adam's) put on my black sedan by a "professional" coating installer. Fast forward to 90 days since applied, I noticed the other day in the sunlight a few streaks in the application. Why did I not see that before? Good question, simple answer is, I do not drive the vehicle that much. But now that I noticed it, I reached out to the installer and guess what, they are no longer located in IL and are now in Arizona. So, back to the question I have to ask, can I reapply another layer of the coating or, do I have to wait years before applying again?
Hi JazzMan, great questions, and sorry you are having issues with the coating on your vehicle! Typically streaks in a coating application have been there since application, but you may not have noticed them in certain light conditions. These streaks are due to either letting the coating flash too long before removing the residue, or not wiping away the residue thoroughly enough. They sometimes appear due to overlap lines with the applicator, or uneven pressure with the applicator when applying the coating. On a super sunny day (or under garage lighting), you may not even see these streaks, as bright sunlight typically hides them; however, if it is a slightly cloudy or overcast day, that is when these streaks will be much more apparent, especially on darker-colored vehicles. They can be fixed though! We would recommend trying Brilliant Glaze on the streak areas - wipe it in back and forth using a Red Hex Grip Applicator with slight pressure, allow it to haze for 10-20 seconds, then buff off the residue with a plush microfiber towel. If that does not fix the issue, you may need to go to a machine polisher with our white Polish and a White Foam Pad, since it has been cured for 90 days now. You can reapply another layer of our Graphene Ceramic Spray Coating for example, which provides around 6 months or more of protection on a daily driven vehicle, and is very easy to apply. Reapplying another layer of the coating most likely will not fix the issue in this case though - reapplying a second layer can usually resolve the streaking problem within the first few hours of applying the ceramic coating but not after several months. If you are still having issues, please send some pictures to "tips@adamspolishes.com" and we can assist you further!
Thank you for this video. I was coating the roof of my Jeep Cherokee and the sky opened up.... The coating ran ALL OVER the body and now the entire thing has drip marks and streaks. So in my case I'd just need to buy polish and a few good pads...
Very informative, feels more safe now to use ceramic coating. I always felt insecure to use it as I was afraid of those high spots and marks I can't get out of the paint anymore. Btw. Use ipa after you polish and before you reapply coating.
IPA is useless against heavy carrier oils on majority of compounds and polishes. You should be using a panel prep solution. You can make some with 10 oz acetone and 22 oz original formula windex in a 32 oz spray bottle.
I think this video is very helpful in at least providing confidence to give it a shot, knowing there are options … but also driving the point others have said, “work on a small area or panel at a time”.
Thanks for the video. I just applied Adam's Advanced Graphene coating on a 2 month old Black Honda HRV (btw you can't see no rainbow on a black car in a normal home garage lighting so that idea went out the window) which had swirl marks galore from the dealer (even on the glass). After prepping for 2 days (almost 16 hours) when I started applying it as a complete newbie to coatings, the first panel I did was the hood copying Pan the Organizer's video. Bad idea. Should have done some small hidden panel because unlike him I am in central Florida in my home's garage and do not have AC running controlling temp and humidity. Most people don't. The coating flashed so fast that I should have stuck with maybe a 2 x 2 section. My whole hood panel had dark and light spots all over and I did not see that till 8 hours later. Tonight at 18 hours, I was able to take a microfiber applicator and rub in some P4 polish I was using from Chemical guys in it and hand polish the hood in sections and using Adam's plush towel that came with the kit wipe it clean and buff it lightly and levelled the coating on that panel. There were some other streaks elsewhere and I used Adam's Prep Wipe spray, with a soft towel to rub into the coating for 15 to 20 seconds in sections and then use that plush towel to level them out. That worked even at 18 hours in Florida. I inspected the car in the dark garage with the black light and the coating is still there on the whole surface.
Sorry about the application issues but glad to hear you were able to resolve them without too much trouble. Coatings definitely flash and react on the surface much more quickly in high temperatures and especially high humidity compared to cooler temps and low humidity!
@@AdamsPolishes Your suggestion of trying first in a small side area to see how the coating reacts and sets is a very good suggestion to find the right tempo. I am prepping my wife's VW ID4 now to do the same coating on it
This video is immensely useful. I still don't dare apply a ceramic coating myself, however. I am a professional mechanic, not a detailer. Each to his own I guess. :-)
@@jond8013 Streaking and high spots. Source: I messed up. But I also have a dented used car, just that the paint hasn't faded yet since it was garage kept, and now it's not, so I wanted to keep it that way.
Wow, what a perfect topic and video. I downloaded it for future reference. Thank you, thank you, thank you. I have a case of another company Si02 ceramic coatings, so would Adam's Graphene spray still work on the other coating even if it's not graphene? Thanks.
If you have to use polish and the polishing machine to remove a high spot, should I use an IPA wipe before reapplying the coating in the spot I just polished? To remove all the polishing material?
Hi Jay, yes we would recommend using a small amount of our Surface Prep with a clean plush microfiber towel over that area to remove any polishing oils left behind, before reapplying the coating.
Awesome video! I’ve been thinking of using your Graphene on my Tesla but it’s been a little intimidating. So glad to see it’s easy to fix high spots or areas I missed
Really great and helpful video. The only thing you forgot to show, was to clean the surface with IPA/panel whipe between polishing and reapplying the coating.
After you applied the polish to remove the high spot ( which I have done in the past on small areas) you applied the coating over the top without using isopropyl/ panel wipe to remove any polish? I feel the coating wouldn't adhere 100% to the surface and will wear off quickly! Just my opinion though.
Hi there, great question! We have not witnessed any adverse behavior or performance ability on ceramic coating any automotive cameras - backup, windshield, side and front cameras, mirrors, and so on. You MUST make sure you wipe away the coating residue from the camera lenses, just as you do on paint, glass, lights, etc. If you do not wipe away the coating residue, it could become cloudy and impair the camera if the coating residue were to dry on the lens.
So I’m looking to apply ceramic coating to a Satin wrap. So I’m don’t try think polish will be a acceptable fix as there is not clear coat . I’m in no rush to do my own car so hoping that if I get uneven/high spots I can add more coating to level out?
When I pulled my truck out into the sun, 12 hours later, the hood was extremely inconsistent. Mostly places I had trouble reaching. The polish on an applicator technique worked incredibly well. Just drag the applicator over the areas (no real pressure) then buff out with a towel. Works on glass as well. I wouldn't start this project without some polish on hand.
Scott Mattern gotta get rid of them. I’ve washed a ceramic coating suede applicator immediately after just to see how it would react. The suede is much rougher and will create marring on the paint
after using a machine polisher, wouldn't you use coating prep to take that off first before applying new coating? Or because since it has a base coating on it, you don't need to prep the surface again?
I was actually getting ready to mention this, yes you would use a panel prep, this is a bad example.. if this was a acrylic base polish you could allow the polish to cure for 15-18 hours and re-coat or us a UV lamp to speed it up
Nice, this was exactly the video i needed. I´m about to apply my first ever ceramic coating (Avalon King) once we get better weather and was worried for a number of things that could happen, just because i had no idea what to expect. But this was very reassuring, can´t wait to finally apply it now! Thanks!
Nice! I'm planning on applying the same to my car. In one way, lucky I live in an apartment so not too worried about the weather as my car's in the basement.
@@sensiblewheels Isn´t it too humid there if it´s a literal basement? Or is it heated? The temperature isn´t even worrying me too much, but the humidity around here was on average around 80% the last weeks. My garage doesn´t really help there... Anyways, wish you much success for the coating, can´t wait myself to see how it looks on my Boston Green Metallic! ;)
@@Schmitzelhaus Thanks! Avlonking mentioned on their website that anything below 5° and above a humidity of 70% is very bad for the curing process. I've already ordered mine and in the forecast I see a few days where the temperature (both low and high) as well humidity is okay to let the coating cure. It's not a heated basement! Good luck with yours too! Let us know it goes.
@@damiendegrasse Well, I waited for a while for the Temperature to raise and humidity to drop and I still ended up with tonnes of high spots. I did it In a basement with only a flashlight! So I couldn't see those high spots so loads of light is recommended.
What if you did a contact-less wash with strip wash in a foam cannon? Would that remove the oils but leave the coating intact without any abrasive or need to recoat(even just for peace of mind)?
WOW! priceless informations in this video! what is the better moment to buff the ceramic coat? when the rainbowcolours starts flashing or imediatly after the rainbowcolours ?
Yep you want to polish to get your paint to pop before coating. You seal in whatever look you have when you coat it. Just hit the area with 90% iso alcohol before you coat, after polishing.
Hi Andrew, yes we would recommend using our Surface Prep included with the Graphene Ceramic Coating Kit, after polishing and prior to applying the coating itself. You want the surface as clean and as bare as possible before applying the coating for best adhesion and results.
Extremely helpful thank you for this video! question though, when you use the polish method is it necessary to remove the polish before applying more coating?
No chance. after ceramic coating usage, the applicator must be thrown out because the coating residue on the suede is going to become small glass sharpnels.
recently my igl graphene coating went bad ended up with darker spot and developed water spots after 2 months Spent 2 hours just polish the hood to remove the coating Extremely tough job to remove all coating from the car
I applied Gtechniq Bike Ceramic coating to my brand new TREK Road bike and the result was a disaster . I followed the instructions but waited too long to wipe it off ( 3-4 minutes instead of 1-2) The result was high spots and clouding. In the sun it looks like a little kid got handprints all over the frame.. I went to a detail shop where they used a cutting compound and orbital polisher and 1000-200 grit sanding with no luck. I opted to take the bike back home and was advised by Techniq USA to try RUPES yellow fine polish and the Gtechniq microfiber towel that came with the kit. I doubt it will do much more than the cutting compound used at the detail ship with the orbital. Any suggestions would be appreciated.
Hey there, we do not recommend using our Graphene Ceramic Coating on leather surfaces; however we do offer a separate coating formula specifically for interior surfaces, Adam's UV Leather & Vinyl Coating. You can find it here: adamspolishes.com/products/adams-uv-leather-vinyl-coating
If I am applying the ceramic coating and notice a spot that I should have polished better how do I wash off the ceramic off that panel to go back and re-polish this spot so I can reapply ceramic to that panel
Hi Kenneth, you won't be able to wash off the ceramic, but you can use our blue Compound with a Microfiber Cutting Pad with a random orbital polisher to compound the ceramic coating off of that area. Then finish it down with our White Foam Pad and white Polish, then use Surface Prep and reapply the coating to that panel.
We do not recommend re-using applicators. As you noticed, used applicators can scratch and then you will have to do re-work. We recommend using opposite sides of an applicator, 180 degrees apart, so that you can get 2 uses per applicator, then discard it. The sides and especially the edges can harden and become crystallized with ceramic resin that WILL scratch the finish.
I had a literal nightmare for my first time using this the other day. We had a heat wave in Cali. It was 95f even in my shop. High spots GALORE. and nearly immediately after applying. I had to run a 30 second cure time... working on a 2 ft section at a time. Anyone have any pointers? Did I do something wrong?
Hi Willy, yes the small suede applicators and the larger gray microfiber applicator blocks can harden and develop crystallization in the face of the applicator once the coating dries into the surface. You will feel a difference between the side of an applicator that was used to apply the coating compared to the opposite side that you were holding with your hand. Once the coating hardens into the applicator and dries, that side could then scratch paint if you try to use it again. Reactivating the hardened side with more coating will make the applicator more pliable, but you still run the risk of scratching a surface, so it's best to use another side of the applicator or grab a new fresh applicator when you want to coat another vehicle.
I have applied adams graphene ceramic spray to my Tesla and it looks amazing. However the windshield has once spot where there are dry water spots and I need to remove the ceramic to completely clean the windshield. Any idea how to remove this?
Hi AJ, great question with lots of great debate. With our Graphene Spray Coatings, you can usually soak the towels in a bucket of water and 1-2oz of Towel & Pad Revitalizer immediately after use, and then wash them separate from your other towels - you do not want to contaminate other delicate towels with ceramic resins. For the more durable 60ml Graphene Ceramic Coating, the coating is more thick and can crystallize in the towels just like it does with the applicator, especially in the Suede Coating Towels in the kit. You can try to soak these towels as well, but the towels can become less absorbent and actually become hydrophobic and repel water. If the towel feels rough, keep in mind that it will most likely scratch a vehicle at next use, so you can downgrade these towels to a different task - wiping up spills on the floor, oil changes, or other messy jobs - before throwing them out.
I managed to salvage a suede applicator by spraying it generously with a heavy duty degreaser, massaging it into the applicator, then rinsing it very thoroughly and letting it dry. I did it right after I finished using it, so the resins hadn't crystallized.
You guys are the first big detailing company I ever stumbled on - love your products. Thanks for giving me the confidence to fix my most recent coating high spots.
Thank you Jack! We certainly appreciate the kind words and thank you for your business!
IPA after polish to remove the oils before applying coating to ensure proper adhesion!
What happens if I dont
Might not need it
@@Mr.duke10783 you cry
@@sebastian-daquanglocknerjr1883 lmao
He forgot to, didn't he?
This was one of your better videos!! Very informative and great camera angle to be able to see the high spots.
I like this video, as it applies to any brand of coating, and any brand of polish, rather than specifically naming particular products as a promo for Adam’s products. I really appreciate that.
🚗🙂👍
You saved my bacon fella
Applied my first attempt at ceramic coating yesterday to fully prepared Jaguar XJ
Could believe how difficult it was given minimal instructions etc
Loads of dark high spots in the panels
Left one side alone luckily
Came in searching for solutions came across your straightforward video exactly what I needed
Got up early next day and polished out all panels and got rid of the blemishes
Will now have to pluck up courage to try again!
Thanks 😅
I did the same thing but not on the whole car. I was able to hand polish with microfiber applicator and level the coating without getting rid of it. It is still there but I caught it before 24 hours passed
Am just finishing up my own DIY applying Adam's Graphene Ceramic Coating (original formula, not advanced), and there were a couple unexpected things I ran into, partly because I did mine outside and not under artificial light.
First, I was surprised that my prep resulted in a kind of dull, almost satin finish before applying the coating. Was happy to see that applying the coating restored the "shiny, wet" look.
Working outside, I found that I couldn't see the coating flash due to lighting conditions. I then resorted to simply estimating by time, knowing from various videos to expect flashing to occur up to 2 minutes, so manually timed myself (estimation) and produced a fairly good result.
But, as one might expect, there were some intermittent problems.
I'd check back again in about 3-5 hours and see the cross hatches of my application in a combination of different angle and different light (again, this was outside). I was able to simply add another layer of coating and the problem was resolved. One patch in particular wasn't discovered until about 12 hours later and still was fixed by simply adding a new coat.
All things considered, am happy with results to this point. Shortly after full curing, I'm then hopeful that I'll really get 7 years of outside protection from the sun!
Had the same challenge as you in not having a well-lit garage. One other tip they mention in another video is to go off of feel. Once the solution starts to feel tacky/sticky, it’s pretty well-cured. Time that, and you can sort of go off of feel.
After you use an abrasive shouldn’t you use surface prep to ensure any solvents left behind are removed from the surface before you reapply the ceramic coating?
Yes. You want to hit it with an IPA to ensure best likelihood for the ceramic coat to bond with the clear coat.
I guess the best way is taping a square to do abrasive,then use IPA to wipe before reapplying ceramic coating.
Great video...
Wish I would have known this before my first Adams ceramic coating🥴
But no worries...I figured them out...had good success with Sonax perf. Finish & microfiber applicator pad...some light hand polishing took care of the high spots and the UV light helps tremendously to check coverage & for high spots...👏👏👍👍
In my training, we were taught to before the ceramic coating, to wipe the surface with a panel wipe. We used Gyeon, then a ceramic prep spray, then the ceramic coating was applied.
I have a new car on the way...and have your kit. Knowing there are ways I can fix any mistakes I make gives me so much more confidence to do this for my very first time. Thanks for your great how to videos. I have some polish on the way too...just in case I have to make corrections before and after!
Please remind viewers to also IPA wipe down after any polishing and before reapplying new coating. Oils left behind from polish will preventive coating from properly curing and diminish its protective properties.
Ipa?
@@Aninebula Isopropyl Alcohol
I was thinking the same. That has got to be an issue with bonding.
Thank you for this video! Now I feel more confident that I can fix my mistakes.
There is too much taboo behind ceramic coating. Thank you for clarifying the easy of fixing any screwups!
How to remove ceramic coating from camera lens? I coated my tesla and didn’t properly remove/level it from edges of the camera lens and now edges are showing blurry on the screen. I used the Adams graphene ceramic coating advanced and it's been around 36 hrs at the time of posting this. Appreciate your help.
This video helps eliminate the fear as beginner myself. Thanks for this video
This is why I use adam’s products. Not only do they have great products they have great tutorials as wel
I used the graphene kit as instructed and had awesome results. I did get a little over ambitious covering too much area all at the same time and some of the ceramic coating did begin to set up before I could polish it off. I used a plush towel with the boost spray and it evened out beautifully. On my black and chrome road king the ceramic coating makes the bike appear brand new. Great products from Adam’s! 👍🏻
That right there is the key to ceramic coating. Little areas start to finish then move on.
By the way.. when you say “Cure”, what you really mean is “Flash”. Ceramic coat’s “flash time” is typically when it ready to wipe off (typically second to minutes) vs “cure time” is when the ceramic coating hardens and is safe to be driven (typically 2/3 days and up to a week sometimes to be fully cured).
So, the liquid Ceramic Spray can be used as a leveling agent within 2 hours?
Let's say you let it flash, but you're having a hard time seeing the rainbowing before you wipe, can you spray a dusting of the Ceramic Spray before doing the final wipe to avoid high spots?
That sweet sweet labeling on the ceram coatings for easy following of the video. Prime video production, even two years ago.
Why was it ok to reapply the coating ontop of polish instead of using a panel wipe or surface prep first?
I'd like to know too.
I've just thought the same thing. Definitely messed up there.
it was ok because they created an additional 'back link' to their website using google's youtube app.
Backlinks are a top way marketers ensure their site has high SEO rankings so that said marketer's target search terms people use when they search google shows up in this case Adams' website in the first few results of the user's search results.
@@theconnectedchris305 wha?
@@barbaroacosta5335 it’s not ok to do so. The bond in that spot is going to be weaker. But installers won’t redo a whole panels. So this video is more with fixing a mistake on high spots. I don’t ceramic my own cars. A good 4 times a year of a paint sealant and wax is cheaper than 1200+ ceramic coating. Plus you have to pay to maintain that coating. From washes and spray wax. To reapplying. Cause you can get tar or rough spots from contaminates where you will clay the car again. As a professional detailer to a customer. My advice is don’t put faith in ceramic coating. It’s pretty hyped up and not worth the cost.
Great products I have been using them for years. The industry makes it out like ceramic coating is so hard to do. It's easier than old-school waxing.
Tried to coat my new painted trim pieces for my car but I ended up having a lot of noticeable "brush strokes" if you will when I took them outside in the sun. Tried to rehydrate but could not replicate these results. The coating was only on the pieces for about 45min to an hour when I tried this. 🤷♂️
Hello, thank you for the video. Question, I had a graphene coating (Adam's) put on my black sedan by a "professional" coating installer. Fast forward to 90 days since applied, I noticed the other day in the sunlight a few streaks in the application. Why did I not see that before? Good question, simple answer is, I do not drive the vehicle that much. But now that I noticed it, I reached out to the installer and guess what, they are no longer located in IL and are now in Arizona. So, back to the question I have to ask, can I reapply another layer of the coating or, do I have to wait years before applying again?
Hi JazzMan, great questions, and sorry you are having issues with the coating on your vehicle! Typically streaks in a coating application have been there since application, but you may not have noticed them in certain light conditions. These streaks are due to either letting the coating flash too long before removing the residue, or not wiping away the residue thoroughly enough. They sometimes appear due to overlap lines with the applicator, or uneven pressure with the applicator when applying the coating. On a super sunny day (or under garage lighting), you may not even see these streaks, as bright sunlight typically hides them; however, if it is a slightly cloudy or overcast day, that is when these streaks will be much more apparent, especially on darker-colored vehicles. They can be fixed though! We would recommend trying Brilliant Glaze on the streak areas - wipe it in back and forth using a Red Hex Grip Applicator with slight pressure, allow it to haze for 10-20 seconds, then buff off the residue with a plush microfiber towel. If that does not fix the issue, you may need to go to a machine polisher with our white Polish and a White Foam Pad, since it has been cured for 90 days now. You can reapply another layer of our Graphene Ceramic Spray Coating for example, which provides around 6 months or more of protection on a daily driven vehicle, and is very easy to apply. Reapplying another layer of the coating most likely will not fix the issue in this case though - reapplying a second layer can usually resolve the streaking problem within the first few hours of applying the ceramic coating but not after several months. If you are still having issues, please send some pictures to "tips@adamspolishes.com" and we can assist you further!
thank you, very helpful as im starting my detailing journey
I was surprised he didn’t wipe with IPA after using polish for the latter high spots, before reapplying more coating.
Thank you for this video. I was coating the roof of my Jeep Cherokee and the sky opened up.... The coating ran ALL OVER the body and now the entire thing has drip marks and streaks. So in my case I'd just need to buy polish and a few good pads...
Very informative, feels more safe now to use ceramic coating. I always felt insecure to use it as I was afraid of those high spots and marks I can't get out of the paint anymore. Btw. Use ipa after you polish and before you reapply coating.
No wipe down with IPA b4 reapplying the coating?
i was wondering the same .
Maybe the IPA will 'hurt' the good leveled coating you applied before?
IPA is useless against heavy carrier oils on majority of compounds and polishes. You should be using a panel prep solution. You can make some with 10 oz acetone and 22 oz original formula windex in a 32 oz spray bottle.
This will probably be the most highly watched video of the bunch.
I think this video is very helpful in at least providing confidence to give it a shot, knowing there are options … but also driving the point others have said, “work on a small area or panel at a time”.
That rehydrating trick is cool. Reminds me of taking old dry erase off of a whiteboard
Watched this video and this trick worked even after I had high spots from 2 months ago.
This is such a helpful video. You guys make great content!
Should you have used I.p.a after polishing compound before reapplying coating?
i thought the same, plus, taking the car in the sun while ceramic coating is curing? dont't know about that
If you spot correct a high spot and reapply a coating it will be a lighter spot. Usually have to do the whole panel.
This is not always true, depends on the coating but yes I completely agree on that with a lot of coatings
thankls fella, great insight i feel much more confident armed with this knowledge, cheers and keep up the utube vids fella, i am a fan..
I about had a cow when I found a high spot near the door. Thanks to this video...problem solved. Thanks Adam's
Thanks for the video. I just applied Adam's Advanced Graphene coating on a 2 month old Black Honda HRV (btw you can't see no rainbow on a black car in a normal home garage lighting so that idea went out the window) which had swirl marks galore from the dealer (even on the glass). After prepping for 2 days (almost 16 hours) when I started applying it as a complete newbie to coatings, the first panel I did was the hood copying Pan the Organizer's video. Bad idea. Should have done some small hidden panel because unlike him I am in central Florida in my home's garage and do not have AC running controlling temp and humidity. Most people don't. The coating flashed so fast that I should have stuck with maybe a 2 x 2 section. My whole hood panel had dark and light spots all over and I did not see that till 8 hours later. Tonight at 18 hours, I was able to take a microfiber applicator and rub in some P4 polish I was using from Chemical guys in it and hand polish the hood in sections and using Adam's plush towel that came with the kit wipe it clean and buff it lightly and levelled the coating on that panel. There were some other streaks elsewhere and I used Adam's Prep Wipe spray, with a soft towel to rub into the coating for 15 to 20 seconds in sections and then use that plush towel to level them out. That worked even at 18 hours in Florida. I inspected the car in the dark garage with the black light and the coating is still there on the whole surface.
Sorry about the application issues but glad to hear you were able to resolve them without too much trouble. Coatings definitely flash and react on the surface much more quickly in high temperatures and especially high humidity compared to cooler temps and low humidity!
@@AdamsPolishes Your suggestion of trying first in a small side area to see how the coating reacts and sets is a very good suggestion to find the right tempo. I am prepping my wife's VW ID4 now to do the same coating on it
you blew my mind with the uv light! great video!
This video is immensely useful. I still don't dare apply a ceramic coating myself, however. I am a professional mechanic, not a detailer. Each to his own I guess. :-)
What happens if you mess up?
It’s as easy as waxing your car.
@@jond8013 Streaking and high spots. Source: I messed up. But I also have a dented used car, just that the paint hasn't faded yet since it was garage kept, and now it's not, so I wanted to keep it that way.
Wow, what a perfect topic and video. I downloaded it for future reference. Thank you, thank you, thank you. I have a case of another company Si02 ceramic coatings, so would Adam's Graphene spray still work on the other coating even if it's not graphene? Thanks.
Great video Joe, thanks for putting it up there. It answered a lot of questions!
Thanks! I used this method and helped me correct a dumb DIY mistake.
You do not remove polish residu with an IPA solution before re apply the coating?
If you have to use polish and the polishing machine to remove a high spot, should I use an IPA wipe before reapplying the coating in the spot I just polished? To remove all the polishing material?
Hi Jay, yes we would recommend using a small amount of our Surface Prep with a clean plush microfiber towel over that area to remove any polishing oils left behind, before reapplying the coating.
Awesome video! I’ve been thinking of using your Graphene on my Tesla but it’s been a little intimidating. So glad to see it’s easy to fix high spots or areas I missed
Do you have a Tesla?
@@ImAHelicopterItIsSir I do
Really great and helpful video. The only thing you forgot to show, was to clean the surface with IPA/panel whipe between polishing and reapplying the coating.
This video should have a lot more views.
Really cool people here ! i used to be their fedex guy . Its cool seeing you again joe . We still have to go golf !!
Great Video, I just did my first application of Ceramic and definitely have high spots. This video was spot on!
I do 15-18 coatings a month and I am sitting here right now fixing this job I did. It was a 97 degree day and 78° humidity
So how long do you let your ceramic coating cure for before wiping it off? And do you use the Adam’s graphene ceramic/advanced ?
awesome video the best i have ever seen very well explained.
After you applied the polish to remove the high spot ( which I have done in the past on small areas) you applied the coating over the top without using isopropyl/ panel wipe to remove any polish? I feel the coating wouldn't adhere 100% to the surface and will wear off quickly! Just my opinion though.
Is this safe to put over the lenses on my car's cameras? Tesla Model Y. Im wondering if it would have adverse effects on auto pilot?
Hi there, great question! We have not witnessed any adverse behavior or performance ability on ceramic coating any automotive cameras - backup, windshield, side and front cameras, mirrors, and so on. You MUST make sure you wipe away the coating residue from the camera lenses, just as you do on paint, glass, lights, etc. If you do not wipe away the coating residue, it could become cloudy and impair the camera if the coating residue were to dry on the lens.
Why do you not have to spray the prep spray after you polished it?
So I’m looking to apply ceramic coating to a Satin wrap. So I’m don’t try think polish will be a acceptable fix as there is not clear coat . I’m in no rush to do my own car so hoping that if I get uneven/high spots I can add more coating to level out?
Excellent information ✊Would love to use Adams garage to do my car.
Big D from what i see here if Adams did your car they would have it for approx. 9 days.
When I pulled my truck out into the sun, 12 hours later, the hood was extremely inconsistent. Mostly places I had trouble reaching. The polish on an applicator technique worked incredibly well. Just drag the applicator over the areas (no real pressure) then buff out with a towel. Works on glass as well. I wouldn't start this project without some polish on hand.
Excellent video. Can you advise me on a lamp model to see the high spots ?
Is there a way to salvage those suede applicators, like soak immediately in APC, or are they done after being used with a coating?
Scott Mattern gotta get rid of them. I’ve washed a ceramic coating suede applicator immediately after just to see how it would react. The suede is much rougher and will create marring on the paint
@@ethanlinkous5620 thanks
after using a machine polisher, wouldn't you use coating prep to take that off first before applying new coating? Or because since it has a base coating on it, you don't need to prep the surface again?
I was actually getting ready to mention this, yes you would use a panel prep, this is a bad example.. if this was a acrylic base polish you could allow the polish to cure for 15-18 hours and re-coat or us a UV lamp to speed it up
Nice, this was exactly the video i needed. I´m about to apply my first ever ceramic coating (Avalon King) once we get better weather
and was worried for a number of things that could happen, just because i had no idea what to expect.
But this was very reassuring, can´t wait to finally apply it now! Thanks!
Nice! I'm planning on applying the same to my car. In one way, lucky I live in an apartment so not too worried about the weather as my car's in the basement.
@@sensiblewheels Isn´t it too humid there if it´s a literal basement? Or is it heated? The temperature isn´t even worrying me too much, but the humidity around here was on average around 80% the last weeks. My garage doesn´t really help there...
Anyways, wish you much success for the coating, can´t wait myself to see how it looks on my Boston Green Metallic! ;)
@@Schmitzelhaus Thanks! Avlonking mentioned on their website that anything below 5° and above a humidity of 70% is very bad for the curing process.
I've already ordered mine and in the forecast I see a few days where the temperature (both low and high) as well humidity is okay to let the coating cure.
It's not a heated basement!
Good luck with yours too! Let us know it goes.
@@sensiblewheels I have to be careful, my humidity levels are around 80-90% right now
@@damiendegrasse Well, I waited for a while for the Temperature to raise and humidity to drop and I still ended up with tonnes of high spots.
I did it In a basement with only a flashlight! So I couldn't see those high spots so loads of light is recommended.
Should u use ipa to remove the polishing oils before reapplying the coating or do u not have to
This was very Informative. Thank you
What if you did a contact-less wash with strip wash in a foam cannon? Would that remove the oils but leave the coating intact without any abrasive or need to recoat(even just for peace of mind)?
WOW! priceless informations in this video!
what is the better moment to buff the ceramic coat? when the rainbowcolours starts flashing or imediatly after the rainbowcolours ?
Was helpful for me. I have some high spots I need to fix.
Our pleasure Dave, glad we can help out!
You can apply a coating over freshly applied polish? Or does the polish prevent the coating from adhering?
Yep you want to polish to get your paint to pop before coating. You seal in whatever look you have when you coat it. Just hit the area with 90% iso alcohol before you coat, after polishing.
Notice you apply ceramic coating directly after polish? Most preps ask to IPA or equivalent after polish and before coating.
Hi Andrew, yes we would recommend using our Surface Prep included with the Graphene Ceramic Coating Kit, after polishing and prior to applying the coating itself. You want the surface as clean and as bare as possible before applying the coating for best adhesion and results.
Extremely helpful thank you for this video! question though, when you use the polish method is it necessary to remove the polish before applying more coating?
I would do so yes. Theres still residu from the polish on there. Just a little IPA and recoat. IMO
What’s the best way to clean the applicators that have been used for the ceramic coating???
Garbage after ceramic use.
No chance. after ceramic coating usage, the applicator must be thrown out because the coating residue on the suede is going to become small glass sharpnels.
recently my igl graphene coating went bad ended up with darker spot and developed water spots after 2 months
Spent 2 hours just polish the hood to remove the coating
Extremely tough job to remove all coating from the car
I applied Gtechniq Bike Ceramic coating to my brand new TREK Road bike and the result was a disaster . I followed the instructions but waited too long to wipe it off ( 3-4 minutes instead of 1-2) The result was high spots and clouding. In the sun it looks like a little kid got handprints all over the frame.. I went to a detail shop where they used a cutting compound and orbital polisher and 1000-200 grit sanding with no luck. I opted to take the bike back home and was advised by Techniq USA to try RUPES yellow fine polish and the Gtechniq microfiber towel that came with the kit. I doubt it will do much more than the cutting compound used at the detail ship with the orbital. Any suggestions would be appreciated.
Great informational video! Thank you!
So can I use UV light when removing coating to make sure it’s all gone?
How long should you let the Graphene coating sit before whipping off
10:22 you don't have to use buffer. You can use rubbing compound and buff it out with towel, and then reapply the coating.
Does the rubbing compound of turtle wax will work?
@@vinchannel0019 yup... that's what I'm using.
@@vinchannel0019 just do it lightly and do not put too much pressure.
If no action is taken to remove high spots, would they dissipate/ disappear over time as the coating breaks down?
Hello@Adam's Polishes
, would you like to review the new MJJC foam cannon pro? Thanks.
If i have half the ceramic advanced bottle left, how long is shelf life?
Would it be the same process if it was left on the glass (side mirror) for more than 24 hours? Thanks.
Awesome video, a topic that is rarely covered by how to videos. Definitely eases my worries about the process
This is all over hyped. All those products to use just to buy into the hype. Just re apply a thin coat on the surface and work it out. It wud work.
Hello chaps, Do you know where I can buy your products in the UK ?
Hi there! You can check out www.prestigecarcareshop.com They are an authorized reseller of our products 👍
can the graphene be applied to interior seat such as a model Y vegan leather?
Hey there, we do not recommend using our Graphene Ceramic Coating on leather surfaces; however we do offer a separate coating formula specifically for interior surfaces, Adam's UV Leather & Vinyl Coating. You can find it here: adamspolishes.com/products/adams-uv-leather-vinyl-coating
If I am applying the ceramic coating and notice a spot that I should have polished better how do I wash off the ceramic off that panel to go back and re-polish this spot so I can reapply ceramic to that panel
Hi Kenneth, you won't be able to wash off the ceramic, but you can use our blue Compound with a Microfiber Cutting Pad with a random orbital polisher to compound the ceramic coating off of that area. Then finish it down with our White Foam Pad and white Polish, then use Surface Prep and reapply the coating to that panel.
Are the applicators reusable , the one I have became crisp, although I “rehydrated” it with the coating, it scratched my finish.
We do not recommend re-using applicators. As you noticed, used applicators can scratch and then you will have to do re-work. We recommend using opposite sides of an applicator, 180 degrees apart, so that you can get 2 uses per applicator, then discard it. The sides and especially the edges can harden and become crystallized with ceramic resin that WILL scratch the finish.
Can you get the blue hand polish to fix hot spots?
Super helpful! Thank you!
I had a literal nightmare for my first time using this the other day. We had a heat wave in Cali. It was 95f even in my shop. High spots GALORE. and nearly immediately after applying. I had to run a 30 second cure time... working on a 2 ft section at a time. Anyone have any pointers? Did I do something wrong?
Thanks for the video.. Question Can you use the Graphene Spray first and follow up with the Graphene Ceramic?
It should be used the other way around
I just went through this. Had to machine polish high spots. I don’t find the advanced coatings, either spray or bottle, to be very forgiving.
How can i remove Adams Ceramic Coating Advance high spot from PPF without messing up the PPF?
very helpful video... I’ve had issues with this myself and it’s good to know some techniques to correct it
Awesome video what happens it’s on matte paint?
That was a great, informative video, thanks for posting!
If you're reapplying the coating after polishing don't you need to use a polish remover first to remove the oils?
Can you clean and reuse the applicator pads? Or do they harden up
Hi Willy, yes the small suede applicators and the larger gray microfiber applicator blocks can harden and develop crystallization in the face of the applicator once the coating dries into the surface. You will feel a difference between the side of an applicator that was used to apply the coating compared to the opposite side that you were holding with your hand. Once the coating hardens into the applicator and dries, that side could then scratch paint if you try to use it again. Reactivating the hardened side with more coating will make the applicator more pliable, but you still run the risk of scratching a surface, so it's best to use another side of the applicator or grab a new fresh applicator when you want to coat another vehicle.
I have applied adams graphene ceramic spray to my Tesla and it looks amazing. However the windshield has once spot where there are dry water spots and I need to remove the ceramic to completely clean the windshield. Any idea how to remove this?
Are the towels used for ceramic application ruined? Or can they be washed?
Hi AJ, great question with lots of great debate. With our Graphene Spray Coatings, you can usually soak the towels in a bucket of water and 1-2oz of Towel & Pad Revitalizer immediately after use, and then wash them separate from your other towels - you do not want to contaminate other delicate towels with ceramic resins. For the more durable 60ml Graphene Ceramic Coating, the coating is more thick and can crystallize in the towels just like it does with the applicator, especially in the Suede Coating Towels in the kit. You can try to soak these towels as well, but the towels can become less absorbent and actually become hydrophobic and repel water. If the towel feels rough, keep in mind that it will most likely scratch a vehicle at next use, so you can downgrade these towels to a different task - wiping up spills on the floor, oil changes, or other messy jobs - before throwing them out.
I managed to salvage a suede applicator by spraying it generously with a heavy duty degreaser, massaging it into the applicator, then rinsing it very thoroughly and letting it dry. I did it right after I finished using it, so the resins hadn't crystallized.