This is RodBuilding Episode #5 Finishing like a Pro
Вставка
- Опубліковано 6 вер 2024
- In this episode of “This is RodBuilding,” Gary shows how to finish your rod! Gary offers some excellent techniques, ideas, and his go-to way of finishing a rod. This is a step-by-step video with some excellent info all over this video.
Make sure you subscribe and ring the bell, so you don’t miss any future episodes.
www.Americantackle.us
Facebook: / americantackle
Instagram: / americantackle
Twitter: / americantackle
TicTok: / americantackleco
American Tackle Rod Building Group: / atcrodbuilding
If you have any questions, please reach out to us:
Phone: 1-800-516-1750
Email: info@americantackle.us
Took all of two videos for me to subscribe :) Great videos!
Good tips Gary! Love these new how to rod build videos.
Many thanks! 😊
LOVELY Gary!
Cherz buddy!
Best vid on fishing rod epoxy I’ve seen yet. Thanks bud.
Lots of information and some great tips as usual Gary. Great video.
This was a timely video. I just finished wrapping a 9ft 3wt fly rod. Next up: epoxy. Many thanks for all the tips.
Tip: Don't dispose the epoxy in the foil immediately. Use it to feel if the epoxy is curing properly, rather than touching the rod.
Love the video! I picked up something again from your tips, even though I’ve been building for a long while there can always be something that can be helpful, tiny things you don’t think about that can make a huge difference
Awesome Gary!! I’ll be using some of these tips for sure 👍..these videos are easy to follow and full of good stuff!! Good stuff AT and Gary 👌
Many thanks Jason
Very well done. I agree that most videos showing this process skip over some important info. This guy hits all the important and gives great visuals and explanations of why it's done the way it is. Thanks AT for putting this out
Thankyou for taking the time to watch Reed 😊
Good tips!
Very nice tips video, thanks! Can you tell me which type of blank or what materials need a thin layer epoxy for whole blank?
nice video - thanks for the tips! at what RPM are you running your drying motors? does it make a big difference if they are e.g. running at 9rpm or 18rpm?
Very simple answer to your question regarding the O rings on your drying wheels the answer is you look for silicon O rings - Clear and Zero marking
Hi Gary where do you find your disposable brushes and is there a difference between the yellow and the violet?
Thanks
Darryl
Gary
What is the brand of your rail runner thread carriage
Can they be purchased in Florida?
Made a half dragon scale and it came out great thanks for the tips
Bob
Epoxy game strong💪
great tips! will get myself a tack rag. what rod dryer is on the wall?
Mega video Gary!
Thanks mate!😊
How long should you wait until you do your second coat of epoxy? And will the epoxy still bond to itself if you wait more than 24 hours between coats?
Can you thin down epoxy if its too thick and how would you do that?
Being AT Pro Staff, any chance of asking them to sort the Chuck on their power wrappers. I see you have the same issue as everyone else with an off centre Chuck.
All the forums are full of the same complaint and yet it is still an issue.
Brilliant video by the way, pretty much as I do, except the tip about the foil and plate. I have always used the small foil trays you can buy as I mainly build fly rods and don’t need big volumes of epoxy. However, just doing a set of carp rods so that tip will come in handy. Thanks.
Hi Rob
That chuck has since been replaced with something new… The old AT powerwrapper is discontinued but the future is bright! 😜
@@truecustomrods6937 I hope it bright 😀 You can see why Alps sells so many Chuck upgrades :)
At what speed do you apply the coat?
🌟
Tackar!
What kind of 2 step guide is that you are using?
ZOOM in more.