I hooked up the transformer probes to my kids bed, no more hangovers for him, he is out of bed before the heat come on. Love the Beckett Burner and alligator clips too.
Hey Steven, I think what you are sharing is great and you are definitely doing a good job. Do you have any videos on Beckett AF2 150 repair and diagnostic would be greatly appreciated. I'm having issues with mine. KEEP UP THE GOOD WORK 👍
Morning... my blower runs but hesitated at the start... I need to turn the fan with screwdriver from ignightor box and then it runs... does this mean I need a new motor?. Just replaced the ignightor.. wasnt the problem. Thanks in advanced... great series btw
Yes, I'm aware. My Beckett will be converted to a babington burner. Clogging is not an issue with this design. The fans are different in the two units. Can these be swapped?
Hey Steve. On a Beckett Clean Cut A2EA 6527 there are 2 inlet ports, One on the bottom and one on the side. Does it matter which one the supply line connects to ?
I took off a R7284U and when i went to put it back on the wires got knock and i think I got them all put back to the right wire nuts but the red limit wire where does it go. I did it all watching your videos and on training #7 u refer to the swaping the red and black. That's all go but where do they go?
Carroll Cooper well you would have to chace the wires back one should come from high limit problem the red one and the black wire most likely is a constant power for post purge .after the burner is satisfied the burner will run for a pre deturmaned time on post purge .the burner must be wired properly do not mess with it if you are not sure .call a burner man if your not 100% sure what goes were.its not worth dieing over
Hey Steve I have a beckett burner I've tried to bleed out I have roth oil tank and suction line went bad I replaced it. Now I can't hear the motor run. I can look in threw the draft I don't see it spinning. What could cause the motor not to spin. When I try to bleed it drips out thanks
How would you know if the inlet is bad? I ran out of fuel about two times. The last time, i put about ten gallons in, but i waited until the morning and when i went to bleed it, nothing came out. I chained the filter n checked the line, and there's fuel in the line. When i take the line off from the inlet, i don't see any. Can the inlet be locked?When i took the pump apart, the screen was like new.
you have to blead the air out off pump there is a small bleaded at bottom of pump open a fue turns then run burner till you get a good fow of oil then close .you really should just call a oil burner man someone that know what he is doing
I hear that! I tried to bleed it, but nothing came. I've bled it many times in the past before. I've changed a few parts before. I've changed the parts inside the burner before and it's been running good for a long time. I know how to clean it out and all. I never had a problem with the inlet and fire mat tic. I'm not sure if that closed off, and blocking the fuel. Thanks for your information. Is there anyway to tell if the fire mat tic is closed?
He said the coupler was cracked... He replaced the coupler, new oil filter and nozzle... Burners working great now... I just wan't sure why the broken coupler caused no flame? I'm not to up on burner repair...
Got it going yesterday. The end caps were not damaged, only that black plastic in the middle. Cut a piece of 5/8 heater hose and put the end caps in it and it worked great. Wouldn't trust it as a permanent fix, but at least I have heat again while the new part is on the way.
steven lavimoniere Thanks, got the part yesterday, but waiting for new nozzles, before I replace the coupling. Thanks for all the Beckett videos. Very helpful.
Hi. Sorry its me again. I posted a short video of my problem under my name. Philip Grombliniak. I wanted to know how to remove blower motor with only an inch and a half clearance on the right(motor side) side. My boiler is hanging from the ceiling in the kitchen(this is the same in all Levittown ranch houses on long Island. You will see in my video the motor is almost against the wall. And you will hear the "clicking "noise the bearing is making. Also at the end of the burner cycle for 1 second as the motor slows to a stop. It sounds like a marble rolling sound. I am hopefull that maybe when I pull the motor out slightly I could get an Allen key in and release the cage. Would you be able to check out my video and advise. If you were closer I would of course have you come and look at it.
I hooked up the transformer probes to my kids bed, no more hangovers for him, he is out of bed before the heat come on. Love the Beckett Burner and alligator clips too.
John S thanks for commenting john
Excellent series keep up the good work 👍
You taught me most of what I know about Beckett. Including latex gloves.
First Webster burner I've seen.
Awesome car in the background.
Hey Steven, I think what you are sharing is great and you are definitely doing a good job. Do you have any videos on Beckett AF2 150 repair and diagnostic would be greatly appreciated. I'm having issues with mine. KEEP UP THE GOOD WORK 👍
Great video....great car in the background too.
thanks dean
Morning... my blower runs but hesitated at the start... I need to turn the fan with screwdriver from ignightor box and then it runs... does this mean I need a new motor?. Just replaced the ignightor.. wasnt the problem. Thanks in advanced... great series btw
Steve, thanks for the awesome series. please do a video of opening and cleaning the pump strainer.
Johnny Matthews look through my oil burner videos i have all that stuff in them videos
Great videos! I have learned a lot. How hard is it to convert an AFB to an AF? I need one for a waste oil burner. Thanks!
urgentcareguy3 waste burners are different ..then home heating burners ..
Yes, I'm aware. My Beckett will be converted to a babington burner. Clogging is not an issue with this design. The fans are different in the two units. Can these be swapped?
Great videos! I saved a service Call!!
Hi I have a question mine i can only get it to fire up if I plug the return line any help I can get from you guys?
Thanks for the informative videos
enjoying the series
thanks andy
Hey Steve. On a Beckett Clean Cut A2EA 6527 there are 2 inlet ports, One on the bottom and one on the side. Does it matter which one the supply line connects to ?
+Frank Reddy eather one if it said inlet thats the supply port
I took off a R7284U and when i went to put it back on the wires got knock and i think I got them all put back to the right wire nuts but the red limit wire where does it go. I did it all watching your videos and on training #7 u refer to the swaping the red and black. That's all go but where do they go?
Carroll Cooper well you would have to chace the wires back one should come from high limit problem the red one and the black wire most likely is a constant power for post purge .after the burner is satisfied the burner will run for a pre deturmaned time on post purge .the burner must be wired properly do not mess with it if you are not sure .call a burner man if your not 100% sure what goes were.its not worth dieing over
Does the plastic fan housing help the fan performance? Or correct air flow paths?
Hey Steve I have a beckett burner I've tried to bleed out I have roth oil tank and suction line went bad I replaced it. Now I can't hear the motor run. I can look in threw the draft I don't see it spinning. What could cause the motor not to spin. When I try to bleed it drips out thanks
jfernandez2082@gmail.com it tripped out on safety .. you have to reset the protector relay ..
steven lavimoniere thanks it's all good now.
Ye oil burnar ka motor coyel ka di gram hoga apka pass
cool thanks again Steve
+Gerardo Mireles thanks for watching
thanks for all the great videos! very educational. keep up the great work!
How would you know if the inlet is bad? I ran out of fuel about two times. The last time, i put about ten gallons in, but i waited until the morning and when i went to bleed it, nothing came out. I chained the filter n checked the line, and there's fuel in the line. When i take the line off from the inlet, i don't see any. Can the inlet be locked?When i took the pump apart, the screen was like new.
you have to blead the air out off pump there is a small bleaded at bottom of pump open a fue turns then run burner till you get a good fow of oil then close .you really should just call a oil burner man someone that know what he is doing
I hear that! I tried to bleed it, but nothing came. I've bled it many times in the past before. I've changed a few parts before. I've changed the parts inside the burner before and it's been running good for a long time. I know how to clean it out and all. I never had a problem with the inlet and fire mat tic. I'm not sure if that closed off, and blocking the fuel. Thanks for your information. Is there anyway to tell if the fire mat tic is closed?
you might have a blockage it should bleed try it again if it don't work call in a professional
ok thanks!
i have an old bard with no bleed ,do you bleed it off the oil filter?
I can't believe the sounds they make once the fuel filter disintegrates and gets trapped in the nozzle.
Two pipe system rocked.
Are the motors interchangeable between burner chassis?
Great . I have a few questions. Is this the forum I should ask them in or is there another website or email?
ask and i will answer you
Great video... You really know your s**t... Thanks... I lost flame and hot water... The guy said that the coupler in the pump was broken?
well was the motor to pump coupler bad yes or no?????????
He said the coupler was cracked... He replaced the coupler, new oil filter and nozzle... Burners working great now... I just wan't sure why the broken coupler caused no flame? I'm not to up on burner repair...
How long is the coupling without the end caps? Got to make sometime up until the new part comes in. Beckett 2454.
+rfn944 i buy mine percut for beckett and for carlin
Got it going yesterday. The end caps were not damaged, only that black plastic in the middle. Cut a piece of 5/8 heater hose and put the end caps in it and it worked great. Wouldn't trust it as a permanent fix, but at least I have heat again while the new part is on the way.
rfn944 good thinking on your feet
steven lavimoniere Thanks, got the part yesterday, but waiting for new nozzles, before I replace the coupling. Thanks for all the Beckett videos. Very helpful.
Hi. Sorry its me again. I posted a short video of my problem under my name. Philip Grombliniak. I wanted to know how to remove blower motor with only an inch and a half clearance on the right(motor side) side. My boiler is hanging from the ceiling in the kitchen(this is the same in all Levittown ranch houses on long Island. You will see in my video the motor is almost against the wall. And you will hear the "clicking "noise the bearing is making. Also at the end of the burner cycle for 1 second as the motor slows to a stop. It sounds like a marble rolling sound. I am hopefull that maybe when I pull the motor out slightly I could get an Allen key in and release the cage. Would you be able to check out my video and advise. If you were closer I would of course have you come and look at it.
6:16, what size set screw is the by pass plug?
Well I figured out the screw size. Installed, and she works. Great video!
this would be great if you'd just show how the adjust the air.fuel intake.
+cypher24713 thats something that comes with experience hard to show on a video .
very nice
thanks wink
👍🇨🇦😃
See