Bro! Wait till you see the video. X cam dropped right in baby! I've heard of this before where the cranks are casted slightly tighter on random hemis. I was looking forward to that too....🙄
You said you had a clearance issue with the crank and cam. Are you referring to the cam hitting the bottom of the piston sleeve or did the lobes hit each other?
I would do both for sure. Stage 1 will give you the biggest jump in horsepower for the smallest amount of money. The stage 2 only gives a small performance boost with its cam. The rest of the items in the stage 2 are more for strength and longevity of the motor and only give a very tiny amount of a performance boost. Basically, stage 1 gives better performance and stage 2 gives strength to the motor to handle the increased performance.(new cam adds power but not as much as the stage 1 kit)
That was the governor gear that the plastic governor gear meshes with to keep the motor from running at higher rpms. You don't actually have to remove it when removing the governor but it equates to a tiny bit less rotating mass when removed.
@@chandlercustoms8242 good stuff man, any idea on the HP and Torque numbers? I'm kickin' around the idea of cracking open my 212 mounted on a mud motor setup and gettin' er breathing right
@@padronianful I have never had this motor tested so I'm not sure what its actually putting out. These mods can get expensive very quickly, but I know that if you go as far as porting and shaving the head, adding roller rockers, putting the right cam in it, and tuning it properly, you can get them up in the low 20s horsepower range. We stopped this particular build at the Stage 2 and it seems to be plenty of power. If you don't want to go internal, the Stage 1 kit offers an amazing hp gain at a very low cost.
I'm going to have to watch your video about 200 times before I learn how to install my kit. Slow down!! Let me know when you make a super slow video 😊. I got brain damage thank you 😊
Hemi the valve covers bigger no it’s shiny and small plus hemis are used more for machinery like snow plows wood chippers and stuff like that hope that helped ill name more ways why its different 😀
@@chandlercustoms8242 Genuine Mikuni as oppose to that Chinese Mikuni copy,...much better,..it's funny that people choose that copy because it's a little less money !!
More like a stage 3 build with piston isn’t it I only seen the stage 2 kits come with springs cam rod and flywheel. Nice job on the build bro💪🏾💯
Bro! Wait till you see the video. X cam dropped right in baby! I've heard of this before where the cranks are casted slightly tighter on random hemis. I was looking forward to that too....🙄
Sounds like a winner
Nice build!! Engine runs good.
How man ft pounds of torque do I use for the billet piston rod to clearance of the crankshaft
did you use the bolts from the low oil sensor to plug the holes left by the governor?
He used 1/4 self tapping bolts sold by gopowersports
Why did you skip the cam install?
I was hoping to see how he fit those Champion rockers on that hemi head....Just kidding. Good video.
What's the difference between the hot cam, and the mod cam? I'm trying to get lots of speed
Hot cam revs to 7500rpm mod 2 cam is 7000+rpm
You said you had a clearance issue with the crank and cam. Are you referring to the cam hitting the bottom of the piston sleeve or did the lobes hit each other?
on the hemi engines you have to shave off part of the ears by the rod journal so they don’t hit the cam
Nice build bro
Hey man one question for ya is the stage 1 kit necessary if i want to install the stage 2 kit or i can skip stage one and go straight to stage 2 ?
I would do both for sure. Stage 1 will give you the biggest jump in horsepower for the smallest amount of money. The stage 2 only gives a small performance boost with its cam. The rest of the items in the stage 2 are more for strength and longevity of the motor and only give a very tiny amount of a performance boost. Basically, stage 1 gives better performance and stage 2 gives strength to the motor to handle the increased performance.(new cam adds power but not as much as the stage 1 kit)
@@ReflectedBrewing Also allowing to go to significantly higher rpms
Did you install the stock crankshaft key or did you install the 8degrees advance?
It is still running the stock key but I may have to remedy that now that you mention it!
The ARC flywheel has the 8 degree advance built in.
I have a 212 power fist engine, will this work on my engine
What lubricant are you using for the bolts and other stuff
Why did you run it prior to changing the springs?
Did u use break in oil for the first 30 min or r u ok using 10w-30?
I buy oil that say High Zinc
Sounds good!
What carb size and jet size y are using
What was that gear you removed off the crankshaft and what does it do exactly
That was the governor gear that the plastic governor gear meshes with to keep the motor from running at higher rpms. You don't actually have to remove it when removing the governor but it equates to a tiny bit less rotating mass when removed.
@@chandlercustoms8242 Ahhh !!
Ok bro where did you get that puller from????
Harbor freight has them cheap
Ola como eu consigo esse volante
Can I send my motor in pay for the labor and shipping already have the stage 2 kit
Any lawn mower shop that does engine repair should be able to help you out with that
Nice work do you do sell engines that are built for public
I do not sell or build any engines at this time but may again in the future. My day job keeps me quite busy.
Who sells the stage kits for these? Also for 79cc. I want the billet flywheels since I’m running without a gov. Thanks. Great video.
You need to build and sell them with stage 2 kits! Because I’m willing to pay the price for one!
@@ricksmotorizedbikeprojects9572 Affordable Go Karts. AGK. For the 79cc. They pretty much have an do everything for them.
What cam
Looks badass, why not swap the exhaust though too?
Only used the stock exhaust for the break-in. It has a nice header on it now. I'll have to post a video of it running on the go-cart it was built for.
@@chandlercustoms8242 good stuff man, any idea on the HP and Torque numbers? I'm kickin' around the idea of cracking open my 212 mounted on a mud motor setup and gettin' er breathing right
@@padronianful I have never had this motor tested so I'm not sure what its actually putting out. These mods can get expensive very quickly, but I know that if you go as far as porting and shaving the head, adding roller rockers, putting the right cam in it, and tuning it properly, you can get them up in the low 20s horsepower range. We stopped this particular build at the Stage 2 and it seems to be plenty of power. If you don't want to go internal, the Stage 1 kit offers an amazing hp gain at a very low cost.
@@padronianful I'll throw a video of it running up.
@@chandlercustoms8242 thanks for the info man, would you recommend governor removal with the Stage 1 or Stage 2 kits? I've heard mixed answers
What cam was that
HOT-265 CAM w/ 22lb springs from GoPowerSports
@@chandlercustoms8242 did you have clearance issue ?
@@redearedslider321 I did indeed. I had to clearance the crankshaft by shaving it down where it was meeting the cam lobe.
@@chandlercustoms8242 was yours a hemi or non hemi
@@redearedslider321 hemi
You need an exhaust
I'm going to have to watch your video about 200 times before I learn how to install my kit. Slow down!! Let me know when you make a super slow video 😊. I got brain damage thank you 😊
just slow down the vid in settings
there's other videos out there in normal speed and the narrator explains stuff.
Anyone in here that can tell me what the deference between hemi vs non
Hemi the valve covers bigger no it’s shiny and small plus hemis are used more for machinery like snow plows wood chippers and stuff like that hope that helped ill name more ways why its different 😀
Was the carb china or actual minkuni
genuine Mikuni
@@chandlercustoms8242 Genuine Mikuni as oppose to that Chinese Mikuni copy,...much better,..it's funny that people choose that copy because it's a little less money !!
Ohh sweet, a stage 2 build with no throttle 😑
Can I send you my motor
you can send her down to me if needed
Sleeper