Thanks for watching! Please consider subscribing to my new channel here: www.youtube.com/@jamminpcs. I'm trying to move the easier hardware stuff there so that I can focus on the more in depth troubleshooting and diagnostic videos here :)
This helped me today two lcd bracket screws (Dell 5400) were stripped. I drilled thru to the chassis ..no damage thank GOD 😂 the screw dropped thru to the chassis
Dell has been bad about this in their laptops made after 2014-2015, been finding a lot of screws GLUED and/or stripped. I feel rage when looking at rugged series latitude laptops lol
This is brilliant idea. I tried on my $2000 new laptop to upgrade memory. It is very scary at beginning drilling into your laptops but it did work with plenty of patience, thank you very much,
I’m going to try that next time. I was working on a Dell, it was a horrible experience, start to finish, and I just drilled out the screws eventually, but with a big bit. Worked decently well, it loosened the screws so they practically came out on their own even without their heads. Tried all the other tricks before that, nothing but frustration
If you slip off the screw and drill other parts of the computer, yes, that will damage other parts of the computer. If you stay on the screw and only drill it, no, it will not affect other parts of the computer :)
The drill bit you use will depend on the size of the screw your trying to drill out. It would have to be the same size or smaller than the size of the screw
How does putting the drill in reverse lift the screw out? We just drilled a hole so there’s nothing to grip it. Mine just continues drilling a hole in the opposite direction..
Yes, this works to remove stripped screws no matter where the screw is located. However, you would want to take extra caution if you choose to try this method as, if you slip, you can damage your motherboard instead of just scratch your case
That depends on the screw but its usually going to be smaller than the head but the same size or slightly smaller than the shaft. Yes, since laptop screws are small, it would need to be a small bit
This method is a bit more advanced than many DIY tricks I have on my channel and does come with a high risk of damaging your computer if you slip or drill too far. Its your choice if you want to take that risk or if you would prefer to pass it on to a computer tech.
I have an m2 6mm screw on my heatsink and it's stripped. I want to replace my thermal compound but can't because of the stripped screw and I don't want to harm the motherboard while trying to unscrew it. Do you have any advice to unscrew it?
@@PC_Monkey but the screw you removed is on the case. Screw I'm trying to remove is on the motherboard(close to the CPU). So I wonder if there are any other ways to unscrew it without damaging the motherboard.
@@Apocalyman Try to use an 1.5 mm flathead screwdriver. If its in a really bad state, use a soldering iron but be careful to not to touch the anything else beside the screw with it.
hello, i have an asus rog zephyrus g15 ga503q, when turned on it’s back to disassemble, the middle right screw stripped & i can not take it out. how should i go about this & would i need to get a new screw once i take the stripped one out?
I usually take out stripped screws as seen here in this video. This process fully destroys the screw so yes, you would need to replace it after this procedure :)
I would attempt it as I have done this many time before. However, its up to each person if they feel comfortable with that. If you slip or go too far, you could definately damage the SSD or other components.
Hi! I have a stripped screw Philips 00 head in an xps 9550. The 1/16” drill bit is about the same width as the thread, so I’m afraid it’ll obliterate the thread. I figure I should go for a 1/32” drill bit which will drill into the center of the thread. If you would share your thoughts on that it would be amazing!! Thanks :)
Yes, if the bit is larger than or the exact same size as the thread, it most likely will ruin it. Another screw most likely wont take to it. So you should go smaller :)
How do i fix when the captive screws in my laptop don't grab onto anything when trying to tighten? It's like whatever they're supposed to grab on to is gone. Thanks.
Yes, that is common unfortunately. Its very possible that the threading on the panel has broken off. There really isnt a 'fix' for that. If that is the case, the panel would need to be replaced.
Then completely come off but I destroyed them so the top came off and the screw part is still in there so I can take it off and replace one of the screws but I don't know about the rest
I know this is a year ago but if you do still respond, would this method be safe to do inside my pc safety wise, like metal going everywhere. (I don’t mind if the old ssd gets damaged since I already cloned it). I have a stripped screw on my ssd nvme which I want to upgrade, I tried a bunch of methods and I think this is my last attempt before I just go into a repair shop.
You would def have to clean out any metal debris and I would make sure the computer is unplugged and the battery is removed. There is a degree of risk with this procedure so I only do it when I need to
I have a different issue but thought to leave it here as it’s the most recent post. My screen is stuck on a black screen with windows logos and “starting windows” on the bottom. Need help please
@@PC_Monkey Thank you for the reply! If I insert a small drill bit and try to drill, it won't move. I have 4 stripped screws on my dell insipron laptop
hi. ive been meaning to ask. is there a way I can email you my issue? I think my laptop audio driver is faulty. I am currently using an external one, I also bought a usb headset but both are sounding very distored. Ive tried all software related troubleshoot but still having the same issue.
For free, I communicate here on UA-cam. For a fee, we can set up a time and talk somewhere else. Which would you prefer? If you prefer here on YT, and assuming you have Windows 10, have you made sure all updates are processed as seen here? ua-cam.com/video/DDv2gJDjfOM/v-deo.html
Sounds like a warranty job for the vendor , experienced something like that ages go and vendor had to fix it under warranty, I think they replaced the motherboard
What size and type is the drill bit that you used? I attempted this on my laptop with a very small lefthanded drill bit and it drilled into it but it didn't budge.
@@Djp1989 Hi! there is some update thankfully. I drilled into it the best I could (carefully) and tried to reverse but, idk if i was being too light handed or what but it didnt work. (By the way, that was for the method shown in the video with the left handed drill bit.) So, I ended up getting a Screw extractor as my last resort, speifically "Be91eiter Damaged Screw Extractor Set, 22 PCS Stripped Kit" on amazon. I drilled in and reversed it and i was able to get 4 screws out but takes a lot of time since you have to go slow and steady. I used the last bits the "dr #10" and "ex #10" in the kit and switch between them after ever 10-20 mins but im sure you could just stay with one and it would work still. Good luck! ^-^ also I tried replying to this so many time but my reply keeps gettting deleted lol, so i hope you can see this and it helps!
ok, I didn't try it, but let's pretend that i got the screw out, but how can I now get a new screw? because, u know, I'll be a weird guy just awkwardly running a laptop with no cover.
Have an hp laptop 17 inch screen and when you take out the CD rom drive the two screws there are stripped but concerned the force will damage the screen because the laptop is closed and obviously upside down. Is this the best option?
@@PC_Monkey im not saying you. Im saying i have a history of these technicians that their goal is not fix your laptop. But really to rob you of your money by lying to you like they will say the LCD is broken and needs to be replaced when in reality it can be fixed through updating drivers.
Thanks for watching! Please consider subscribing to my new channel here: www.youtube.com/@jamminpcs.
I'm trying to move the easier hardware stuff there so that I can focus on the more in depth troubleshooting and diagnostic videos here :)
Thanks I was struggling with 2 screws on my laptop for several hours and this took them out in seconds. Thanks for saving me several more hours
Glad your all set :) Always here if needed !!
This helped me today two lcd bracket screws (Dell 5400) were stripped. I drilled thru to the chassis ..no damage thank GOD 😂 the screw dropped thru to the chassis
Glad your all set :) Always here if needed !!
You gotta help me. Please tell me the drill bit you used.
Dell has been bad about this in their laptops made after 2014-2015, been finding a lot of screws GLUED and/or stripped. I feel rage when looking at rugged series latitude laptops lol
Thanks man! Will try this in the morning. My fault was using a cheap set of screwdrivers.
Good luck !! Let me know how it goes :)
I'm like: "that better work cause I already stripped it with a drill before even seeing this video."
lol hope it helped :)
This is brilliant idea. I tried on my $2000 new laptop to upgrade memory. It is very scary at beginning drilling into your laptops but it did work with plenty of patience, thank you very much,
Thats the trick! Patience and dont go too fast :) Glad this video was helpful !!
As always keep them coming. Well put!!
Thanks Anthony !!!
Is the thread used in this vid left handed
I’m going to try that next time. I was working on a Dell, it was a horrible experience, start to finish, and I just drilled out the screws eventually, but with a big bit. Worked decently well, it loosened the screws so they practically came out on their own even without their heads. Tried all the other tricks before that, nothing but frustration
Glad your all set :) Always here if needed !!
this won't damage the inside of the laptop components?
If you slip off the screw and drill other parts of the computer, yes, that will damage other parts of the computer. If you stay on the screw and only drill it, no, it will not affect other parts of the computer :)
I know I'm a year late but what drill and drill bit did you use? Thank you so much I'm gonnna try this, pray for meeee.
The drill bit you use will depend on the size of the screw your trying to drill out. It would have to be the same size or smaller than the size of the screw
@@PC_Monkey the one I'm trying to get out is like m2.6 or it says that on my laptop anyway
How do you replace a captive screw in a dell laptop
A captive screw?
Have been looking forward to this..
Great to hear !! Glad this video was helpful :)
This is like a last resource method since it destroys the screw.
If a screw is stripped, isnt it already destroyed lol?
Thanks! I tried and it worked
Great to hear !! Always here to help :):)
How does putting the drill in reverse lift the screw out? We just drilled a hole so there’s nothing to grip it. Mine just continues drilling a hole in the opposite direction..
Thank you very much! It worked! A+++
Great to hear !! Always here to help :):)
I have this problem in the last screw of my phone motherboard.... I don't know if this method will work. What do you think ?
Yes, this works to remove stripped screws no matter where the screw is located. However, you would want to take extra caution if you choose to try this method as, if you slip, you can damage your motherboard instead of just scratch your case
Super, worked well!
Great to hear !! Always here to help :):)
drillbit smaller than screw shaft? or head because if shaft thats a very small bit.
That depends on the screw but its usually going to be smaller than the head but the same size or slightly smaller than the shaft. Yes, since laptop screws are small, it would need to be a small bit
I dont really get how does it actually work. how does a drill engage a screw?
i dont have a drill, my screwdrivers are very small like 1.55mm just ordered it and i only unscrewed 4/12 😥
Are you asking for help getting passed stripped screws or help finding the correct sized drivers?
Thanks for the tip
Your welcome !! Happy to help :)
Hey, do you think that hand drill (the one that you need to twist manually) works? It has different sizes of drill bits
I dont understand your question. No, a hand turned drill will not drill out a screw...
Is it too risky to use this method to unhook an SSD latched with a stripped M2 screw?
This method is a bit more advanced than many DIY tricks I have on my channel and does come with a high risk of damaging your computer if you slip or drill too far. Its your choice if you want to take that risk or if you would prefer to pass it on to a computer tech.
I have an m2 6mm screw on my heatsink and it's stripped. I want to replace my thermal compound but can't because of the stripped screw and I don't want to harm the motherboard while trying to unscrew it. Do you have any advice to unscrew it?
This video shows how I remove a stripped screw :)
@@PC_Monkey but the screw you removed is on the case. Screw I'm trying to remove is on the motherboard(close to the CPU). So I wonder if there are any other ways to unscrew it without damaging the motherboard.
@@omeregeakgun Hey man I have the exact same issue. Did you find a solution?
@@Apocalyman Try to use an 1.5 mm flathead screwdriver. If its in a really bad state, use a soldering iron but be careful to not to touch the anything else beside the screw with it.
@@omeregeakgun I tried every head I could think of and nothing worked. I dont have soldering iron and I dont know which one to get/how to use one X_X
hello, i have an asus rog zephyrus g15 ga503q, when turned on it’s back to disassemble, the middle right screw stripped & i can not take it out. how should i go about this & would i need to get a new screw once i take the stripped one out?
I usually take out stripped screws as seen here in this video. This process fully destroys the screw so yes, you would need to replace it after this procedure :)
Is this worth trying on an ssd screw inside a brand new laptop? 😢 I don't want to damage anything or have dust go everywhere in the laptop.
I would attempt it as I have done this many time before. However, its up to each person if they feel comfortable with that. If you slip or go too far, you could definately damage the SSD or other components.
What do I do if the screws are too small to drill into?
You would just need a smaller drill bit :)
Hi! I have a stripped screw Philips 00 head in an xps 9550. The 1/16” drill bit is about the same width as the thread, so I’m afraid it’ll obliterate the thread. I figure I should go for a 1/32” drill bit which will drill into the center of the thread. If you would share your thoughts on that it would be amazing!! Thanks :)
Yes, if the bit is larger than or the exact same size as the thread, it most likely will ruin it. Another screw most likely wont take to it. So you should go smaller :)
How do i fix when the captive screws in my laptop don't grab onto anything when trying to tighten? It's like whatever they're supposed to grab on to is gone. Thanks.
Yes, that is common unfortunately. Its very possible that the threading on the panel has broken off. There really isnt a 'fix' for that. If that is the case, the panel would need to be replaced.
@@PC_Monkey well that's not what i wanted to hear, but thanks for replying!
@@TaylorZ2 Good luck !! Let me know how it goes :)
Then completely come off but I destroyed them so the top came off and the screw part is still in there so I can take it off and replace one of the screws but I don't know about the rest
It was missing screws already. I've never even opened this computer before
Sorry, I dont understand. Are you asking a question? Is one of your screws stripped?
@@PC_Monkey I got it off, but the ends of two of the ones by my disk drive are still stuck and I'm not sure if I have a drill bit small enough
@@fayelefayele2264 You would need a small enough bit unfortunately to minimize the chances of damaging the surrounding case or components :(
I know this is a year ago but if you do still respond, would this method be safe to do inside my pc safety wise, like metal going everywhere. (I don’t mind if the old ssd gets damaged since I already cloned it). I have a stripped screw on my ssd nvme which I want to upgrade, I tried a bunch of methods and I think this is my last attempt before I just go into a repair shop.
You would def have to clean out any metal debris and I would make sure the computer is unplugged and the battery is removed. There is a degree of risk with this procedure so I only do it when I need to
I have a different issue but thought to leave it here as it’s the most recent post. My screen is stuck on a black screen with windows logos and “starting windows” on the bottom. Need help please
What brand computer do you have?
@@PC_Monkey Lenovo thinkpad P50, windows 7
@@kimaure3980 Are you able to try the steps seen here? ua-cam.com/video/2-WDntT-5L8/v-deo.html
what size is that drill bit you used?
It will be different for different screws. You have to match the size of the bit with the size of the screw your trying to drill out
Do I have to use a drill or can I use a hand screw driver?
If you can remove the screw with a hand driver then there would be no reason to drill out right?
I have a intel inside laptop and for some reason i run a game then it turns off
and it makes my screen a little bit darker every 2 seconds and makes a werid sounf
Sound*
Does the computer turn off or experience the screen issues if your not on the game? Also, is the computer overheating?
@@PC_Monkey turns off and screen issue
@@PC_Monkey and yeah when im not on the game
Hello! How I can I use a small drill bit with my drill? Do I need an adjuster?
Im not sure what drill you have but yes, I am able to use a small bit with mine
@@PC_Monkey Thank you for the reply! If I insert a small drill bit and try to drill, it won't move. I have 4 stripped screws on my dell insipron laptop
@@camilamonje6066 The bit wont move or the screw wont move? You need the correct size bit for the screw
Is this method too risky for a stripped screw on a HDD caddy
I would attempt it but I do it fairly regularly so you may or may not wish to attempt it. Its up to you
I was struggling to take a tiny x screw. I bought a kit for like 3$ it has the appropriate screwhead for the screw
Ya, some computers use weirdly unique screws. Glad your all set :)
hi. ive been meaning to ask. is there a way I can email you my issue? I think my laptop audio driver is faulty. I am currently using an external one, I also bought a usb headset but both are sounding very distored. Ive tried all software related troubleshoot but still having the same issue.
For free, I communicate here on UA-cam. For a fee, we can set up a time and talk somewhere else. Which would you prefer?
If you prefer here on YT, and assuming you have Windows 10, have you made sure all updates are processed as seen here? ua-cam.com/video/DDv2gJDjfOM/v-deo.html
Sounds like a warranty job for the vendor , experienced something like that ages go and vendor had to fix it under warranty, I think they replaced the motherboard
What size and type is the drill bit that you used? I attempted this on my laptop with a very small lefthanded drill bit and it drilled into it but it didn't budge.
It depends on the screw you are drilling. The bit would need to be slightly larger than the screw thread
Any update on this?
@@Djp1989 Are you having a hard time with a screw too? What are you looking for?
@@Djp1989 Hi! there is some update thankfully.
I drilled into it the best I could (carefully) and tried to reverse but, idk if i was being too light handed or what but it didnt work. (By the way, that was for the method shown in the video with the left handed drill bit.)
So, I ended up getting a Screw extractor as my last resort, speifically "Be91eiter Damaged Screw Extractor Set, 22 PCS Stripped Kit" on amazon. I drilled in and reversed it and i was able to get 4 screws out but takes a lot of time since you have to go slow and steady. I used the last bits the "dr #10" and "ex #10" in the kit and switch between them after ever 10-20 mins but im sure you could just stay with one and it would work still.
Good luck! ^-^ also I tried replying to this so many time but my reply keeps gettting deleted lol, so i hope you can see this and it helps!
@@bloopbanana5465 You needed to buy a drill separately from the extractor set?
ok, I didn't try it, but let's pretend that i got the screw out, but how can I now get a new screw? because, u know, I'll be a weird guy just awkwardly running a laptop with no cover.
You can either purchase them online, places like Ebay, Amazon, etc. Or you can get them from your local hardware or computer electronics store.
OK, where did you buy that small drill bit?
@@barajuboor I purchased a set of drill bits as my local Home Depot.
cool !
Happy to help :) Always here if needed !!
Have an hp laptop 17 inch screen and when you take out the CD rom drive the two screws there are stripped but concerned the force will damage the screen because the laptop is closed and obviously upside down. Is this the best option?
I would open the computer up, and rest the keyboard on a desk or something while the LCD hangs down the side. Did I explain that correct?
@@PC_Monkey yes thanks
My hard drive screw is strip 😂
Bummer :( If you choose to deal with the situation this way, be careful as you dont want to slip and damage the HDD!
@@PC_Monkey thx for the heads
Up but ima actually removing the hard drive to replace it with a new one
Is this safe??? Taking off the stripped screws
Well wearing safety glasses so no, its not super safe which is why I wear protective gear. Not sure if I understand what your asking lol
I am afraid that maybe i will drill something else accidentally 😬
Ya, you have to make sure you keep the drill on the screw unfortunately :)
these fookin technicians are doing it on purpose
?
@@PC_Monkey im not saying you. Im saying i have a history of these technicians that their goal is not fix your laptop. But really to rob you of your money by lying to you like they will say the LCD is broken and needs to be replaced when in reality it can be fixed through updating drivers.
@@darrylwolfe7359 oh sorry. This was a video on how to drill out a screw lol so I didnt really understand your comment
the metal going into the area of the board is dangerous. Don't do this.
lol wow