your the only guy up here showing us the location of these switches and how to replace them. Thanks! Good job well done. Please share any info you have regarding trans filter location and replacement. Thanks again!
I just wanted to say THANK YOU! You saved me a lot of money by giving me this info on how to do it myself. Followed your directions to the T and it worked great. I even changed the 3rd gear switch like you recommended. Car is running like a champ and the best part...No Check Engine Light. I had a few misfire's in cylinder 3 and 5. Changed Sparks plugs with top rated Platinum's and All good to go! I thought I was going to need to replace the coil packs, tested each one individualy and there all working as they should. Thanks again for your help!
Do you have to get a new washer when you swap the part? The service manual seems to indicate you should replace it along with the part. I am about to change the third gear switch on my 09 Fit.
hi, i saw your vudeo and liked how you explained step by step.. my car same acura tl 2000 3.2. the d5 light started to blink at times it does and sometimes it doesn't., could this be any help? if i replace 3& 4 gear switch!?
I have an Acura TL 2004 transmission code and Drive flashing light p0873 fourth gear pressure switch but it's driving perfectly fine. Where is location? And how bad can this be?? Second transmission put in. Transmission might be under warranty but not labor. What do you recommend and how many of these you seen before?
Hi mate, big thanks to share such a informative videos. I have learned alot from your channel. I have 2000 honda accord 2.3 litre with 4 speed automatic transmission. When i come to stop it jerks very badly, just like somebody hit me from the back. Shifts nice and smooth but that jerks is so bad. What the problem could be? Thanks
I have a 03 tl and once I start my car cold and put it on reverse it kicks back hard and I replaced my motor mounts year ago.when the car gets warmed up and I put it on reverse it wouldn't kick as hard as when it's cold but car shifts pretty good cold any suggestions??
I have my 2012 Acura TL, the car was parked since 2017 now When I put in Drive it does not move, but it does move only on reverse. Do I need to change the transmission fluid?
My 2003 Acura TL same... Kicks back hard when starting cold. Heard that if you park by stepping foot brake first before putting in park (just change order of putting in park and foot brake) , then maybe that helps reduce the kickback when putting in reverse when cold start. Try it... Not sure if it works.
Hello i have a 1994 lincoln town car, my transmission wont go into overdrive. Can u plz give me some tips on how to test solenoid, and how to track down my problem. Ty.
Actually the 2nd gear pressure switch is NOT located in the transmission. It's located below the throttle body. So in other words, is IS located outside the transmission.
I have that problem with my acura to the code i get is (P2646 rocker arm port 1 perf. Or stuck off) what could this be? the guy at acura says it could be my pressure gage or VTEC sylinoid thats not engaging and that it could screw my rocker arm up and even burn through fuel faster :( what do you think it might be and how can I fix it , what would the cost be just a rough estimate?
hey bro I'm a new subscriber. would damage to a down stream 02 sensor trigger this code? . I ran over a shreded diesel tire on the highway an soon as I did I got a check engine light. took it to AutoZone an got this code along with a damaged 02 sensor. I replaced the 02 sensor an reset the light. I'm waiting to see if I get the check engine light again.
What means the color on the presure switch on my odyssey got one green and one black its diferent or what happen if install on wrong place it fails or are same thing
+misael pacheco Hello, the green and black are different PSI rating Black switch is a 33 Psi Green is 38 Psi If you don't get them correct expect problems.
I have a question see if you experiencing this issue? I have TL 06 A/T and for some reason shifting from 1st to 2nd gear it does a lil stuttering not a kick it is a light shaking while shifting then it keep shifting normal as I go with no problem I have put the ODB reader and does not find a code. At first I thought it was my transmission mounts but they look good I even replace them what you suggest it could be?
My '05 started doing the same thing. After about 20-20minutes of driving, it starts having difficulty going into gear. Cold is ok. Should I change all the pressure switches out or is it done? Can these transmissions be rebuilt and perform well, or is a lower milage replacement better?
Abel Cortez II I would replace it and see what happens. It's not expensive to do and is going to be a hell of a lot cheaper than rebuilding the transmission.
+ldryway rodriguez Did you ever replace your switches? And if so, did it work? I have the same shudder at the top of 3rd gear before the shift to 4th. Wondering if it will do the trick.
does anyone know if it will be better to change the transmission fluid and filter before i change these pressure switches? or does it not really matter?
I had my transmission rebuilt in my 02 Acura about 2yrs ago...and now it jerking at the start of acceleration. The code reads P1740...I hope its just a minor fix which means the 4th pressure switch is bad...I can afford another trans!
Hi, I have an Acura tl 2000..and my. D5 lights started blinking at times could this video help this problem.... im pretty desperate i bought the car and a month later the transmission fixed :-/ and now this problem is happening :-/
I just had a problem with my Honda Accord 2007 V6 this morning, when i was driving the car shook suddenly and it gave me a “D” blinking and a check engine light. After that my car lose power and revving up to 3000rpm in 60mph. After realizing i may have a problem, i stopped and put the car to park and turned off the engine. I checked and open the engine cap, there was no smoke. And i decided to to turn the car back on. And the car gave me only a check engine light no more blinking D. After a few miles of driving the car gave me the same problem like i first mentioned above. Sigh... This cars engine was rebuilt 2 months ago i have driven it about 6000 miles with the new engine. Can somebody help me?? 😭😭
Your Trans is probably dead. If you want to keep the car then don't get it rebuilt - throw the transmission in the garbage where it belongs and find a '06-'07 Honda Accord V6 transmission (about $800). They bolt right up and a shop should do it for about $500 or so. Instructions are on Acruazine.com
That means a code (like P0845) has just been noticed by the computer. Likely the 2nd, 3rd, or 4th clutch pressure switch getting gunked up or gone bad. Cleaning or replacing the switch will help fix that.
Fixed the P1740 code in my 2000 TL because of this video. Went for a drive and rescanned. No more codes. Thanks for posting this video!
your the only guy up here showing us the location of these switches and how to replace them. Thanks! Good job well done. Please share any info you have regarding trans filter location and replacement. Thanks again!
Actually I have a video on replacing the trans filter as well. Just look in my channel! Thanks for watching, cheers!
I’m having the same code 1740 bro what do you highly recommend me to to I’m lost
I just wanted to say THANK YOU! You saved me a lot of money by giving me this info on how to do it myself. Followed your directions to the T and it worked great. I even changed the 3rd gear switch like you recommended. Car is running like a champ and the best part...No Check Engine Light. I had a few misfire's in cylinder 3 and 5. Changed Sparks plugs with top rated Platinum's and All good to go! I thought I was going to need to replace the coil packs, tested each one individualy and there all working as they should. Thanks again for your help!
Hey np, glad was able to save you time and money. gl with the car, cheers!
Thanks for watching, GL.
Video helping in 2020 this video is legendary
Thank you brotha helped me get my sisters car fixed she didnt have the money to take it to the shop
Where did you guys buy the 3rd and 4th gear switch?
Jules Cortez you can get it from acura dealership
acurapartsforless.com
Bought mine from ebay both for like 20$
Does this video work for my honda odyssey
Does the 3rd gear pressure switch regulate the shift "to 3rd" or "from 3rd (to 4th)"?
Great Video! I'm going to change that gear on my car this weekend!!
is that the same part for the 05 tl too
I have a 2002 Honda Odyssey with P1740 showing up, Can use the same steps in the video for the replacement of the pressure switch?
What exactly is that “upgrade” I have it too I was wondering why my fill spot wasn’t same as other videos
Thank you, this should be almost identical to both my 2001 Accord and 2002 Odyssey, they are basically the same car
Do you have to get a new washer when you swap the part? The service manual seems to indicate you should replace it along with the part. I am about to change the third gear switch on my 09 Fit.
Not a 100% but they are not on the outside of the transmission.
yes they were
Also should you put anti-seize on the sensor threads?
Thanks for the video, looks simple to change. Where did you purchase the part?
hi, i saw your vudeo and liked how you explained step by step.. my car same acura tl 2000 3.2. the d5 light started to blink at times it does and sometimes it doesn't., could this be any help? if i replace 3& 4 gear switch!?
what is the part number of the pressure swich of the third gear, it is the same piece for the Honda pilot 2004?
I have an Acura TL 2004 transmission code and Drive flashing light p0873 fourth gear pressure switch but it's driving perfectly fine. Where is location? And how bad can this be?? Second transmission put in. Transmission might be under warranty but not labor. What do you recommend and how many of these you seen before?
Hi mate, big thanks to share such a informative videos. I have learned alot from your channel.
I have 2000 honda accord 2.3 litre with 4 speed automatic transmission. When i come to stop it jerks very badly, just like somebody hit me from the back. Shifts nice and smooth but that jerks is so bad. What the problem could be?
Thanks
do you have a video on how to change 2nd pressure switch
it's on top of the transmission by the upper radiator hose next to it.
I have a 01 Acura TL need help on some things
Is the one to change for the 5 gear?
I have a 03 tl and once I start my car cold and put it on reverse it kicks back hard and I replaced my motor mounts year ago.when the car gets warmed up and I put it on reverse it wouldn't kick as hard as when it's cold but car shifts pretty good cold any suggestions??
Mine does that
I have my 2012 Acura TL, the car was parked since 2017 now When I put in Drive it does not move, but it does move only on reverse. Do I need to change the transmission fluid?
My 2003 Acura TL same... Kicks back hard when starting cold. Heard that if you park by stepping foot brake first before putting in park (just change order of putting in park and foot brake) , then maybe that helps reduce the kickback when putting in reverse when cold start. Try it... Not sure if it works.
Is the 4th gear pressure switch as easy to do on a ford explorer can't find any video's on code p1740 for explorer
does they use the same switch but the computer operator the differently?
my 2003 tl type s jerks some time when it shifts gear and revs in between gears did you have the same problem before you changed all that?
Can you swap the 3rd and 4th switches? would it make a difference?
Hello i have a 1994 lincoln town car, my transmission wont go into overdrive. Can u plz give me some tips on how to test solenoid, and how to track down my problem. Ty.
Do the car still work sense u replaced that
GOD bless you to live long please more video thanks
Eric Torgbor will try, tx for your comment.
Actually the 2nd gear pressure switch is NOT located in the transmission. It's located below the throttle body.
So in other words, is IS located outside the transmission.
I have that problem with my acura to the code i get is (P2646 rocker arm port 1 perf. Or stuck off) what could this be? the guy at acura says it could be my pressure gage or VTEC sylinoid thats not engaging and that it could screw my rocker arm up and even burn through fuel faster :( what do you think it might be and how can I fix it , what would the cost be just a rough estimate?
hey bro I'm a new subscriber. would damage to a down stream 02 sensor trigger this code? . I ran over a shreded diesel tire on the highway an soon as I did I got a check engine light. took it to AutoZone an got this code along with a damaged 02 sensor. I replaced the 02 sensor an reset the light. I'm waiting to see if I get the check engine light again.
Carlos Sanchez
Well? Did you? Still available waiting.
What means the color on the presure switch on my odyssey got one green and one black its diferent or what happen if install on wrong place it fails or are same thing
+misael pacheco
Hello,
the green and black are different PSI rating
Black switch is a 33 Psi
Green is 38 Psi
If you don't get them correct expect problems.
I have a choppy shift from 2nd to 3rd. Other shifts are perfectly smooth. Is there a pressure switch for 2nd gear?
Taylor Holloway no. They only have pressure switches for 3rd & 4th gear ⚙️
I have a question see if you experiencing this issue? I have TL 06 A/T and for some reason shifting from 1st to 2nd gear it does a lil stuttering not a kick it is a light shaking while shifting then it keep shifting normal as I go with no problem I have put the ODB reader and does not find a code. At first I thought it was my transmission mounts but they look good I even replace them what you suggest it could be?
Mine is doing the same thing going from 3rd to 4th. Any suggestions?
My '05 started doing the same thing. After about 20-20minutes of driving, it starts having difficulty going into gear. Cold is ok. Should I change all the pressure switches out or is it done? Can these transmissions be rebuilt and perform well, or is a lower milage replacement better?
Abel Cortez II I would replace it and see what happens. It's not expensive to do and is going to be a hell of a lot cheaper than rebuilding the transmission.
+ldryway rodriguez Did you ever replace your switches? And if so, did it work? I have the same shudder at the top of 3rd gear before the shift to 4th. Wondering if it will do the trick.
I never did but I will do it some time next week
does anyone know if it will be better to change the transmission fluid and filter before i change these pressure switches? or does it not really matter?
I got the same code on my 2003 Honda odyssey but looking for the part it says something different st a auto parts store
i have a 99 TL and my d4 light wont come on. and sometimes it goes into manuel shift. any help? please
Is there a pressure switch for every gear?
No. Only 3rd & 4th gear pressure switches.
I had my transmission rebuilt in my 02 Acura about 2yrs ago...and now it jerking at the start of acceleration. The code reads P1740...I hope its just a minor fix which means the 4th pressure switch is bad...I can afford another trans!
maybe my 03 TL didn't need a new transmission wow
starting to think that now too
@@devantebairos3377 they’ll tell you tell majority of the time
I have an 1999 Acura 3.2 TL. Where do I buy the 3rd/4th pressure switch ?
acurapartsforless.com
Thank you Very insightful
Tricia Coleman np, thanks for your comment.
Hi, I have an
Acura tl 2000..and my. D5 lights started blinking at times could this video help this problem.... im pretty desperate i bought the car and a month later the transmission fixed :-/ and now this problem is happening :-/
F
thanx for the video and plz can u check how to change 1st or 5th pressure switch my car its acura tl 2002
I just replaced the 3rd gear switch and still having it slip. Getting error code p0131
Actually i am getting error code p0730
I have a 2000 honda civic and the transmision have D blinking problem some body can help me to solve this problem?
2004 model????
I have the dread transmission shudder on my 04.
+jcallesano Any update? I have the same thing. Did you change out your switches? New transmission?
+MrJuansWorld worn clutch plates in transmission. replaced under after market warranty. paid 100 bucks for a 3500 tranny. good luck.
Why does my D5 lights flashes and j can’t go through any gears. It’s just Revving up. I have a 2000 Acura TL
Your transmission is bad you need a new one
A pressure switch doesn’t always mean the transmission is going out
Thanks!!
does some one know why my 05 acurs tl will shift into all gears and then out of nowhere it will not go into 1st 3rd and 5th gear
hey brotha did younever find a fix.. my 05 is doing the same thing and its slipping
I just had a problem with my Honda Accord 2007 V6 this morning, when i was driving the car shook suddenly and it gave me a “D” blinking and a check engine light. After that my car lose power and revving up to 3000rpm in 60mph. After realizing i may have a problem, i stopped and put the car to park and turned off the engine. I checked and open the engine cap, there was no smoke. And i decided to to turn the car back on. And the car gave me only a check engine light no more blinking D. After a few miles of driving the car gave me the same problem like i first mentioned above. Sigh... This cars engine was rebuilt 2 months ago i have driven it about 6000 miles with the new engine. Can somebody help me?? 😭😭
I have the same problem on my 2000. Honda civic how do you fix the problem?
@@joseestrada4153 Check the ELD in the main fuse box under the hood.
I’m having the same problem bro did u fix ur problem blinking d5 light
Honda Genuine Parts - Made in China 🇨🇳
My D5 light is blinking, can anybody help?
Your Trans is probably dead. If you want to keep the car then don't get it rebuilt - throw the transmission in the garbage where it belongs and find a '06-'07 Honda Accord V6 transmission (about $800). They bolt right up and a shop should do it for about $500 or so. Instructions are on Acruazine.com
That means a code (like P0845) has just been noticed by the computer. Likely the 2nd, 3rd, or 4th clutch pressure switch getting gunked up or gone bad. Cleaning or replacing the switch will help fix that.