How To Make Special IPR Tool Ford 7.3 Liter Power Stroke Turbo Diesel (1994-2003)
Вставка
- Опубліковано 15 вер 2024
- This is my homemade special tool to remove and install the 1993-1999 Ford 7.3 Powerstroke Diesel IPR ! Cheap and Easy to make. No Welding Required.
What's your opinion? Comment like and subscribe if you appreciate this video. Thank you for watching ! Hope this helps others !
The Best Is Yet To Come !! "You never know what's gonna happen next ! " #NomadLivesMatter
To Contact Me : FreeRangeNomad@Gmail.com or IG: @Free_Range_Nomad
Possible Codes:
P1209 Injection Control System Pressure Peak Fault
P1210 Injection Control Pressure Above Expected Level
P1211 ICP Not Controllable - Pressure Abow/Below Desired
P1212 ICP Voltage Not at Expected Level
P1284 ICP Failure - Aborts KOER or CCT Test
Products in this video:
amzn.to/3CeWbP4 -Motorcraft CM5013 Fuel Pressure Regulator
amzn.to/3KgABwp -1/2 Inch Drive x 1-1/8 Inch Deep 12-Point Impact Socket
amzn.to/3MoJPbZ -Mayhew Select 89062 Carded Cold Chisel Set, 3-Piece
Other Products I use:
amzn.to/2TmQT1X - SAMDO Digital Fuel Level Gauge Universal Fuel Meter Signal Adjustable 7 Color Backlight 52mm 12V/24V 0-190ohm, 240-33ohm, 240-30ohm, 0-180ohm, 10-180ohm
amzn.to/3bTjIJG -White Water Stainless Steel Vented Deck/Fuel Fills - 50⁰ Angle
amzn.to/3finFJQ -MILLION PARTS 17-Gallon Aluminum Top-Feed Fuel Cell Gas Tank W/Oil Level Sensor Silver
amzn.to/3fJ81pW -Draw-Tite 65001 Front Mount Receiver Hitch, Black
amzn.to/3g0CmAH -LUCID 10 Inch 2020 Gel Memory Foam Mattress - Medium Plush Feel - CertiPUR-US Certified - Hypoallergenic Bamboo Charcoal, Twin
amzn.to/3fG9ayy -Petmate Booda Round Edge Litter Scoop
amzn.to/3fMUY72 -Spicer 5-178X U-Joint Kit
amzn.to/3vlAcSA -ACDelco HB88508A Advantage Drive Shaft Center Support Bearing
amzn.to/3bTFw7O -Set of 2 Rear Monroe Shock Absorbers for Ford E-350 Super Duty Towing & Hauling
amzn.to/3wBTrqX -Bilstein 24-174534 B8 5100 Steering Damper Front B8 5100 Steering Damper,Silver,Eye 12mm
amzn.to/3yAxFpw -Monroe 555010 GAS-MAGNUM 65 Shock Absorber
amzn.to/3hTH7P2 -HD Backup Camera System Kit, 7’’1080P Reversing Monitor+Ip69 Waterproof Rear View Camera, Sharp Ccd Chip, 100% Not Wash Up, Truck/Semi-Trailer/Box Truck/RV (FHD1)
amzn.to/3ug7VeM -AOXONEL Outdoor Doormat with Heavy-Duty PVC Backing-Home-Front Doormat Non-Slip Waterproof, Easy Clean Low Profile Mat for Entry (35X23, Brown)
![Ford 7.3 Powerstroke- Rough Running [IPR replacement]](http://i.ytimg.com/vi/CXBHAiPN7W0/mqdefault.jpg)
![Ford 7.3 Powerstroke- Rough Running [IPR replacement]](/img/tr.png)
Nice work. I had more room to maneuver and was able to get a shower valve socket 1-3/32” from Harbor Freight to fit perfect. No special tool needed.
Whatever works without buying a expensive tool.
Harbor Freight PITTSBURGH Shower Valve Socket Wrench Set. Cut the one you need down to the length you need to fit in the spot. The size is either the 1-3/32 in, or 1-5/32 in. Can't remember. You'll find the one by trying them all. May have to hammer the flats flat with a punch as sometimes the socket won't slip over the IPR do to being bowed inward from the crimping process. You'll figure it out. Drill a new hole in the end that a 1/4" drive hardened extension will slide thru so you can have a nice long lever to crack the old one loose and torque the new one in. The cheesy lever/rod it comes with will just bend when you apply any amount of torque to it.
Howdy howdy David 😊..thanks for making hard jobs easy with your knowledge and expertise..right on 👍
Congrats on being the first commenter Jovita !! Thank you for always being here. Are you on FB ? I'd like to send you one of my shirts for free !
@@FreeRangeNomad hey David 😁..I'm not on FB but I would love a shirt..I looked on your description but couldn't find an email address..
@@jovitanavarro7247 daowentpi@aol.com
If you cut all the way through those slots and weld a handle on the socket you have yourself a nice easy tool to use for this job
True. But I didn't have a welder handy. It was being loaned out.
Subbed your channel to by the way, seems to me you've got alot golden gems regarding these late 90s 7.3 liters. Mine I was driving one day and decided to switch from rear to front fuel tank. Previous owner told me front tank was inoperable. But I tried it knowing the tank was full of fuel and a few additives. Anyway the truck ran good for about an hour and then fell on its face and barely stay runnin. I was close to home and nursed her on in. When it fell on its face filter light came on. I changed the filter and topped the bowl off with fuel and it started back up but would cut right off. I checked bowl, still full of fuel. Crank again and it would start run a minute or two and cut off. After I changed the filter I did switch back to rear tank that also was full. Now no matter which tank im on same thing it'll fire up run a minute or two and die. Im wandering if my fuel hose has a hole and is bleeding back? Idk then another topic I have an 05 6.0 and I'm losing injector contribution on 3,5,7 and sometimes 1. So whole passenger side bank. My ficm is good, my glow plug harness is shot. Mechanic told me no compression number 3 cylinder. I put bore scope in thru glow plug hole and my piston looks good two valves were open and 2 were closed. Im going to do a relative compression test to see what that gives me. Because the mechanic said 3 cylinder no compression and either was valve or piston related. So I want to see the drop out from relative compression verifying the no compression. Watching hpop and icp and ficm commands and states everything is doing what it ought to, except my injector contribution test when I toggle them I hear the pintle click. And after I start the truck I starts off losing injector 3 and then 5 and 7 and sometimes 1 then around 2000 rpm they'll come back.
Sounds to me on your 7.3 issue is the switch over valve between tanks is jacked up, clogged, sticking. Check fuel pressure. Maybe something is telling you ecm to shut everything off.
On the 6.0....I had a 2005. I would set it on fire and save the headache and money. Otherwise have entire engine "bulletproofed" and start over. ICYMI...Ford sued Navistar over those faulty engines. They won. But didn't give one penny or help to the million people that owned vehicles with that engine. That's because normally nothing would happen until after the 100k mile factory warranty went out.
Great video !
Thanks! I hope it was useful. Are you working on a 7.3 ??
I just took off the fuel filter and used a shower valve set from harbor freight,saved me a couple swear words lol
Awesome!!
Would a modified wrench have possibly worked? Getting ready to change mine on 97 F350
I'm not sure. Probably. If you have that size wrench you want to ruin to make the mods. My truck is a 97 also.
What size or model # is that piece??
Skip to 2:40
New subscriber. Hi buddy, I’ve got a 99 7.3 shuttle bus do you convert the inside? I liked your build? If so I can give you my number n talk prices. I’m in Dallas Tx. No issues in taking it out to ya
Thank you Manuel for subscribing. I'm sure you will find a ton of useful information here on my channel. Be sure to check out earlier vids and see what cool tricks I've done.
Manuel... Hit me up on InstaGram or Facebook messenger my IG is @free_range_nomad
I fixed this truck so I can sell it and have more money to spend on the Jeep Cherokee and my bus.
Lol Just weld a handle on the cut piece of socket buddy instead of using the chisel
True. But then I would have to keep taking it off and rotate it. Plus...don't have a welder. Thank you !!
@@FreeRangeNomad Cool Beans