You guys just saved me $$$, got the same code and also had issues with the dash. I found online that the switch would fix the dash issues, but was worried about U1411 "fuel", and thought i would take have to take it to dealer. Im going to replace the switch. BTW i did get my original switch replaced via the recall. some people mentioned dealers wanted to charge install to replace it.
Did this today. Thanks so much! I bought a used 2006 Jeep Grand Cherokee and not long after my dash lights began to flicker intermittently. My AC would shut off when this happened and at times my engine would not start. My check engine light then came on and when I checked the code it showed U1411. It was a relatively easy fix and so far the problem seems corrected! Thanks again!
The profanity-edited part might have been useful - it took me a while to figure out how to get the switch assembly out. For future reference, it comes out best when you turn it clockwise while pushing back and down. Then install while turning counter-clockwise. Thanks for the video!
I just want to clarify the ignition positioning when changing this part. My instructions told me to turn the ignition or “run” but there is no “run” mark, just “on” “acc” and “off”. I left the ignition on “off” and changed the old out with the new. I just indexed the new switch to where the old was positioned and it works just fine. No issues. Thanks for posting this! Seeing someone get that Devil dash panel off helped me avoid breaking anything when I pulled mine off. I was seconds away from going Hercules, haha!
Excellent job guys. I just did this. Takes 15 min after you watch this video. The black box you see on the right after you get the ignition screws off the first, second, and third cover. Turn it clock wise so it's facing down. Pops right out.
Finally got around to replacing the ignition switch... man, that was a bear to get out & put back up in the dash.. lol.. took me an hour total. Thanks for the knowledge through this video..
Extremely helpful video. I found that I needed to disconnect the connector to the switch to drop it down. It was still a bitch to get it to drop but eventually I was able to deliver it below the dash. Getting it back in was facilitated by directing the back end in first pointed up. Then move the unit down and forward into the spot.
Thanks to utube and a "special" thanks for your DIY video. Just the right amount of mins long. I watched it twice then went out and replaced my ignition switch in approx 12-14 mins.
Nice video. In my experience if you first remove the blend door actuator located behind the ignition switch is much more easy to remove and install the ignition switch assembly. Remove the actuator is an easy task. Thanks for the good job
Same problem on my '05 Jeep Grand Cherokee Limited which already got a new recalled ignition switch about 3 years ago. Got a check-engine light that turned off and on on its own and ODB-II reader pulled code U1411. Cleared the code and it worked for a while and now having another symptom which is dash lights flashing on startup after AC kicks on. AC will also pulsate. Thanks so much for giving me a strong indication this is just the stupid ignition switch.
Bought the part on Amazon and installed it in about 45 minutes thanks to your video which was full of tips. Interestingly the last repair done by the dealer on a re-call ignition switch was done sloppy. They didn't seat the ignition switch assembly properly and tossed away the top 3rd screw. So far so good. Only time will tell since this is a problem that comes and goes but I am very hopeful!
Putting the whole assembly back in place was a giant two and a half hour chore because of the big plastic box on the side and the metal bracing and all, but my car starts like it should again. Saving money was nothing compared to the relief that it worked. Thanks, I couldn't have even begun without this video.
Great video guys! I was getting the same problem with the re-called replacement part. Cost me about $35 for this part. All is good so far except I hadn't had a beer yet, lol.
So this would be the issue also if you have a remote started because what you saying happens to me. Most of the time i use my remote starter. Keep it mind it never did it when i first put it on. Now at time i use it and will flash lights, turn my AC off and engine light will go on for a few days then it will go away in her own.. with the u1411 code. Please advice
My sons 2005 jeep grand Cherokee Laredo engine intermittently wont turn off after turning key off- can switch be bad? I think he swapped the asd relay - was wondering if maybe fuel pump relay might be sticking could cause issue? He removes the neg vmbattery cable when this happens
I though u1411 had to do with the fuel level/sender?? Help info help??? Confused edit!!!! You answered it. My bad bro! Lol yes my gauge jumped around before. Cool
So I’m having an issue with all dash going off and radio and ac and headlights but my Jeep threw the same code that yours did do you think it’s the same issue?
Got the recall notice last Jan, mine would turn on and act like the batt was dead but the light never dim. Sometimes the batt was dead? Got the switch changed at the dealer then/now 7 months later its doing it again? 2005 Jeep grand Cherokee. Does the same key work in the new switch? thanks for the video it WILL help lol What is does now when i turn the switch it just clicks, do it 4 to 8 times and the starter will turn over? Always worse in the mornings or after its sat for a while. Think its the switch already bad again?
@@jhuntosgarage Thanks I am going to call the dealer again and see if they will do anything, if not i will just buy one...does the same key work in the new switch?
LMAO my dam 05 Grand Cherokee makes the same actuator door noise and it is annoying!!!! I Am glad I found this video I'm trying to get a code readout because my Jeep isn't starting, isn't showing codes on my obd checker, and the check engine light is flashing, I can't haul it to get it looked at or checked at AutoZone because my Jeep is the tow vehicle not the one being towed...not having a good day
I had this code, lights went off, AC shut off, engine went dead got a check engine light with same code than I cleared it and it never happened again, is this similar to what happened to you?
It's been a while so not sure at this point. You'll want to do a new search. If I recall correctly, that switch failed not too long after this video was made.
Did the vehicle reprogram itself to the new switch? Or is the new switch already programmed for the vehicle? Thank you in advance. I get flickering lights in the dashboard I start up. Sometime my vehicle fails to start. Dashboard stays on sometimes even if the key is in the off position
No issue with programming the switch, not needed. I will say that this switch eventually failed too and it was replaced again. Sounds like you need a new switch as well. Thanks for watching!
Hi, I've the same issue. The dashboard used to flash while driving and the AC also sometimes turned off. But the car isn't starting since yesterday. no cranking, no noise at all. When I turn the key on, the dashboard light comes on but the car doesn't start. It accidentally turned on earlier today and I took the car to the mechanic and he said the battery, starter and alternator are working fine. He asked me to go to the dealership to get the ignition switch checked. I just checked your video and now I think I've the same issue. So should I go to the dealership to get it fixed? or I can just buy an ignition switch and get it changed at the mechanic's?
The Blue Boy If it were me, I'd buy the switch and change it myself. This is not hard to do and will probably need to be done eventually anyway. Thanks for watching!
You are not the first person to ask. That noise is a blend door gear (slipping) in the dash. This changes where the air is directed within the dash, fo AC or heat. Not a huge deal to replace.
hey guys my 05 just threw the same code up , on googling , it is said that thus can happen if you use a command start for the car (which i do in canada) ... do i just ignore it or still replace the switch ? what do you think cheers
blair marriott Hmm. Great question. I'm not exactly sure about the command start. If it were my car, I'd wait and see. Clear the code and start the car with the key, then check for the code. Check my channel for a review on the Launch code scanner and the Bluedriver scan tool. Both are very capable. I hope this helps! You can also post the question on my FB page J. Hunto's Garage. Thanks again!
you can ignore the code or have it "cleared" and see if it comes back. if your jeeps electrical stuff (blower, tach, speedo etch) starts quitting on you i would definitely replace the switch
Daniel Cano Garcia I'm sure that they came with the part ordered from Amazon. Shoot me an email at jhuntosgarage@gmail.com and I'll see what I can dig up.
i noticed you said while reading the instructions to ensure the key was in the run position, but then i noticed when you put the ignition back in place it appears the key is in the off position ?? did you turn the key back after installing the new ignition??
craig pelley In the end I think it really didn't matter where it was because we took the keys out to get the switch out (off). I think it's supposed to in run when you separate the switch from the plunger portion. The instructions for this particular switch may have been a bit out of sequence.
michael zayas Tl;DR I'm not sure it's the same part, but I had that exact issue and changed a thing that looks like that part on my blower motor to fix it. I was an aircraft mechanic for 6 years so I got decent at troubleshooting, but I'm not much of a car guy so I might be calling interior gizmos the wrong name 😄 I never called it that, I just thought it was just called an AC blender control, but it looks like the same part. I (literally) changed mine 40 minutes ago, but it was in the glove box on the blower motor and I had to transfer over a plastic gear. Everybody else seems to have one in super crappy positions, so I'm still not 100% sure that it's the same issue. If you've got the clicking on the passenger side with the AC on, I can tell you how I troubleshot it and where the part I changed is at. I pulled mine off, typed in the part number on amazon and ordered the first thing that looked like it. now it works and I've got non-invasive ac.
xin zang This switch had to be replaced a month or so later. After that is was ok. About a year or so later he sold the Jeep to get a Minivan (more kids).
I see in the comments below that someone has asked about the clapping noise. I have looked all over but cant find a video probably because I am not asking the right question can you point me in the right direction please.
You guys just saved me $$$, got the same code and also had issues with the dash. I found online that the switch would fix the dash issues, but was worried about U1411 "fuel", and thought i would take have to take it to dealer. Im going to replace the switch. BTW i did get my original switch replaced via the recall. some people mentioned dealers wanted to charge install to replace it.
Did this today. Thanks so much! I bought a used 2006 Jeep Grand Cherokee and not long after my dash lights began to flicker intermittently. My AC would shut off when this happened and at times my engine would not start. My check engine light then came on and when I checked the code it showed U1411. It was a relatively easy fix and so far the problem seems corrected! Thanks again!
The profanity-edited part might have been useful - it took me a while to figure out how to get the switch assembly out. For future reference, it comes out best when you turn it clockwise while pushing back and down. Then install while turning counter-clockwise. Thanks for the video!
This REALLY WORKED. I REALLY APPRECIATE IT. Cost me 135.00. Switch 45.00 labor 85.00 Thank you
I just want to clarify the ignition positioning when changing this part. My instructions told me to turn the ignition or “run” but there is no “run” mark, just “on” “acc” and “off”. I left the ignition on “off” and changed the old out with the new. I just indexed the new switch to where the old was positioned and it works just fine. No issues. Thanks for posting this! Seeing someone get that Devil dash panel off helped me avoid breaking anything when I pulled mine off. I was seconds away from going Hercules, haha!
Excellent job guys. I just did this. Takes 15 min after you watch this video. The black box you see on the right after you get the ignition screws off the first, second, and third cover. Turn it clock wise so it's facing down. Pops right out.
Judge Jury Glad we could help! Thanks for commenting.
Finally got around to replacing the ignition switch... man, that was a bear to get out & put back up in the dash.. lol.. took me an hour total. Thanks for the knowledge through this video..
Excellent video, that's what needed to be done and after taking it to dealer several times they could not figure it out. Thank you very much.
Extremely helpful video. I found that I needed to disconnect the connector to the switch to drop it down. It was still a bitch to get it to drop but eventually I was able to deliver it below the dash. Getting it back in was facilitated by directing the back end in first pointed up. Then move the unit down and forward into the spot.
Very helpful! Thanks!
Thanks to utube and a "special" thanks for your DIY video. Just the right amount of mins long. I watched it twice then went out and replaced my ignition switch in approx 12-14 mins.
hogrydr100 Awesome! Glad to have helped.
Nice video. In my experience if you first remove the blend door actuator located behind the ignition switch is much more easy to remove and install the ignition switch assembly. Remove the actuator is an easy task. Thanks for the good job
Thanks for the info!
Same problem on my '05 Jeep Grand Cherokee Limited which already got a new recalled ignition switch about 3 years ago. Got a check-engine light that turned off and on on its own and ODB-II reader pulled code U1411. Cleared the code and it worked for a while and now having another symptom which is dash lights flashing on startup after AC kicks on. AC will also pulsate. Thanks so much for giving me a strong indication this is just the stupid ignition switch.
rabunbike I sure hope so. At least it's easy to do and the switch is fairly cheap. Good luck to you and thanks for watching!
Bought the part on Amazon and installed it in about 45 minutes thanks to your video which was full of tips. Interestingly the last repair done by the dealer on a re-call ignition switch was done sloppy. They didn't seat the ignition switch assembly properly and tossed away the top 3rd screw. So far so good. Only time will tell since this is a problem that comes and goes but I am very hopeful!
My 05 did exactly the same thing today after also having the ignition switch replaced on recall.
Mine is doing the same thing. Also after a recall a while back.
When I turn the key into the on position the engine light stays on any idea as to why?
Putting the whole assembly back in place was a giant two and a half hour chore because of the big plastic box on the side and the metal bracing and all, but my car starts like it should again. Saving money was nothing compared to the relief that it worked. Thanks, I couldn't have even begun without this video.
So glad we could help out Greg. Keep an eye on that switch. It may go out again. Thanks for watching!
Great video guys! I was getting the same problem with the re-called replacement part. Cost me about $35 for this part. All is good so far except I hadn't had a beer yet, lol.
Michiana Drone Services LLC Hopefully it doesn't go the way this one did. Had to replace it again. Thanks for watching!
Oh no, I hope not. I bought my part from Napa, so I'm hoping it would be better than some other stores.
Unless it's the PCM.
I’ve had mine replaced 3 times. And now it’s acting up again after 7 months. I’m so fed up
@@StangJeepGrl85 With manufacturer's original part or off-brand? I hadn't had any other problems.
"designed by some engineer at Chrysler who was apparently disgruntled"
hahahahaha Fucking hilarious
just did this today, its easier if you leave the steering colomn...all the way up when tryna get the ignition, in and out of that space
Thanks for the tip!
Thanks for the video. Helped me greatly. All good in the hood now.
Great to hear!
So this would be the issue also if you have a remote started because what you saying happens to me. Most of the time i use my remote starter. Keep it mind it never did it when i first put it on. Now at time i use it and will flash lights, turn my AC off and engine light will go on for a few days then it will go away in her own.. with the u1411 code. Please advice
That knocking noise after start up is one of the blend door motors sticking, I'm sure you aware of that but felt like commenting. Great video
thank you very much for saying so mine is started and I did not know what it was
Just did that fix. What a pain!
This video is right on, follow this and can't mess up - THANK YOU !!!
My sons 2005 jeep grand Cherokee Laredo engine intermittently wont turn off after turning key off- can switch be bad? I think he swapped the asd relay - was wondering if maybe fuel pump relay might be sticking could cause issue? He removes the neg vmbattery cable when this happens
I would definitely start with the ignition switch.
Thanks for making this informative and helpful video
I though u1411 had to do with the fuel level/sender?? Help info help??? Confused edit!!!! You answered it. My bad bro! Lol yes my gauge jumped around before. Cool
Turns out this switch had to be replaced a month or so later, returned to Amazon for refund and purchased a new one at O'Reilly's; all good!
J. Hunto's Garage what is the clapping noise? I have the exact problem i am in the process to replace it but i was wondering about the clapping noises
Dale Sh That is a plastic gear slipping in the AC control box in the dash. I'm sure there's videos on UA-cam for this, it's a common problem.
You are the best thank you so much.
Dale Sh Happy to help!
J. Hunto's Garage did you get any other codes besides the U1411?
Excelent you video. I fixed one that it. I live in Venezuela electronic technician I own Workshop thanks so much
So I’m having an issue with all dash going off and radio and ac and headlights but my Jeep threw the same code that yours did do you think it’s the same issue?
I finally got it bk in place thanks 4 the video
Got the recall notice last Jan, mine would turn on and act like the batt was dead but the light never dim. Sometimes the batt was dead? Got the switch changed at the dealer then/now 7 months later its doing it again? 2005 Jeep grand Cherokee. Does the same key work in the new switch? thanks for the video it WILL help lol What is does now when i turn the switch it just clicks, do it 4 to 8 times and the starter will turn over? Always worse in the mornings or after its sat for a while. Think its the switch already bad again?
Could be a bad switch again for sure. We had to change this one again about a month after we changed this one.
@@jhuntosgarage Thanks I am going to call the dealer again and see if they will do anything, if not i will just buy one...does the same key work in the new switch?
Dude,Thanks for your service..Same model same problem, my question is did you have to replace the key? that in itself is expensive...Thanks
We did not have to replace the key. Not yet anyway. ;)
LMAO my dam 05 Grand Cherokee makes the same actuator door noise and it is annoying!!!! I Am glad I found this video I'm trying to get a code readout because my Jeep isn't starting, isn't showing codes on my obd checker, and the check engine light is flashing, I can't haul it to get it looked at or checked at AutoZone because my Jeep is the tow vehicle not the one being towed...not having a good day
Great informative video. Thanks for sharing.
Thanks for watching!
great video. helped me get mine installed
Glad we could help. Thanks for watching!
I had this code, lights went off, AC shut off, engine went dead got a check engine light with same code than I cleared it and it never happened again, is this similar to what happened to you?
I have the same code on my 2005 grand jeep cherokee but my engine light came on could it be the same issue?
Could be. There are very inexpensive code readers that can identify it.
Thanks for the video bro could you share the company name that brought the new switch thanks again
Purchased on Amazon. Not sure the company name, sorry. Good luck to you.
Hello. Which is the correct link on Amazon to buy this ignition switch?
It's been a while so not sure at this point. You'll want to do a new search. If I recall correctly, that switch failed not too long after this video was made.
Just got this U1411 code today.. I believe this was replaced 4 years ago as a Safety recall..
Did the vehicle reprogram itself to the new switch? Or is the new switch already programmed for the vehicle? Thank you in advance. I get flickering lights in the dashboard I start up. Sometime my vehicle fails to start. Dashboard stays on sometimes even if the key is in the off position
No issue with programming the switch, not needed. I will say that this switch eventually failed too and it was replaced again. Sounds like you need a new switch as well. Thanks for watching!
Hi, I've the same issue. The dashboard used to flash while driving and the AC also sometimes turned off. But the car isn't starting since yesterday. no cranking, no noise at all. When I turn the key on, the dashboard light comes on but the car doesn't start. It accidentally turned on earlier today and I took the car to the mechanic and he said the battery, starter and alternator are working fine. He asked me to go to the dealership to get the ignition switch checked. I just checked your video and now I think I've the same issue. So should I go to the dealership to get it fixed? or I can just buy an ignition switch and get it changed at the mechanic's?
The Blue Boy If it were me, I'd buy the switch and change it myself. This is not hard to do and will probably need to be done eventually anyway. Thanks for watching!
Thanks for the video, it was very helpful ...
I am very glad to hear that. Thanks for watching!!
Buen trabajo
At the end of the video. When you turned the car on that clicking noise. What was that? Mine does that?
You are not the first person to ask. That noise is a blend door gear (slipping) in the dash. This changes where the air is directed within the dash, fo AC or heat. Not a huge deal to replace.
Did this fix last long? My 07 is having similar problems and I think it's the ignition switch also.
Jordan sold it a year or so later so I'm not really sure. But I'd trust a switch from O'Reilly's rather than Amazon about 9.9% more. Just sayin'.
My ignition does that clicking also. 2006 jeep cherokee... what is it. How do I fix it? Thanks for the help
See responses to previous posts. It's in the AC box under that dash, an actuator. Might be pretty easy.
@@jhuntosgarage thanks a lot... I'm tired of that darn clicking lol
hey guys my 05 just threw the same code up , on googling , it is said that thus can happen if you use a command start for the car (which i do in canada) ... do i just ignore it or still replace the switch ? what do you think cheers
blair marriott Hmm. Great question. I'm not exactly sure about the command start. If it were my car, I'd wait and see. Clear the code and start the car with the key, then check for the code. Check my channel for a review on the Launch code scanner and the Bluedriver scan tool. Both are very capable. I hope this helps! You can also post the question on my FB page J. Hunto's Garage. Thanks again!
you can ignore the code or have it "cleared" and see if it comes back. if your jeeps electrical stuff (blower, tach, speedo etch) starts quitting on you i would definitely replace the switch
Do the same key works with the new switch? Or I have to program the key..?
Great question. The same key works as the replacement part is separate from the key cylinder.
Im having the hardest time bring that lock cylinder bk up
Bro me too how'd you do it
Hello, Can you tell me where to get those writing instruction you have used in the video? Thxs in advance.
Daniel Cano Garcia I'm sure that they came with the part ordered from Amazon. Shoot me an email at jhuntosgarage@gmail.com and I'll see what I can dig up.
Just replaced it and my vehicle still doesn't start any other things I should look for?
The usual suspects are spark and fuel. Have to verify you have fuel pressure and spark.
@@jhuntosgarage it has spark and fuel and I just tested the starter it's something else in the ignition switch but idk what
i noticed you said while reading the instructions to ensure the key was in the run position, but then i noticed when you put the ignition back in place it appears the key is in the off position ?? did you turn the key back after installing the new ignition??
craig pelley In the end I think it really didn't matter where it was because we took the keys out to get the switch out (off). I think it's supposed to in run when you separate the switch from the plunger portion. The instructions for this particular switch may have been a bit out of sequence.
awesome thanks man , now to get the bugger back in place lol
craig pelley Glad to help. Check out the playlists on my channel. Probably some things you'll enjoy.
Thanks!
Thanks guys
Thanks for watching!!
Any chance you also had an airbag light on because of thos switch being bad also?
No airbag light that I know of. Thanks for watching!
My ac cuts off then my compus then my airbag light comes on
@FabarmH368 did this work?
Thanks, can't wait to fix this!
Also, that clicking, is that what I think it was?
zadig08 AC blend door gear, stripped! Thanks for watching!
zadig08 what did u think it was
michael zayas
Tl;DR I'm not sure it's the same part, but I had that exact issue and changed a thing that looks like that part on my blower motor to fix it.
I was an aircraft mechanic for 6 years so I got decent at troubleshooting, but I'm not much of a car guy so I might be calling interior gizmos the wrong name 😄
I never called it that, I just thought it was just called an AC blender control, but it looks like the same part. I (literally) changed mine 40 minutes ago, but it was in the glove box on the blower motor and I had to transfer over a plastic gear. Everybody else seems to have one in super crappy positions, so I'm still not 100% sure that it's the same issue. If you've got the clicking on the passenger side with the AC on, I can tell you how I troubleshot it and where the part I changed is at. I pulled mine off, typed in the part number on amazon and ordered the first thing that looked like it. now it works and I've got non-invasive ac.
zadig08 Excellent! I was aircraft weapons maintenance for 11 years. Salute!
J. Hunto's Garage
Small world! By the way, this video really saved my butt, so thanks for that.
How long does that fix last? I heard you had it done before.
xin zang This switch had to be replaced a month or so later. After that is was ok. About a year or so later he sold the Jeep to get a Minivan (more kids).
I see in the comments below that someone has asked about the clapping noise. I have looked all over but cant find a video probably because I am not asking the right question can you point me in the right direction please.
Richaun Facey Try searching Blend door actuator replacement. Another great channel to search is South Main Auto. Hope this helps you. Good luck!
thank you! thats what I was looking for
Could this cause your jeep not to start?
Definitely could.
Asen vídeos y no dan bien la explicación mejor no agan nada
Quantas mas explanacion tu necessitas? Gracias!
I have a 2007 dodge charger and it is throwing u1411 and u1403 codes. Could it be the same thing? id imagine so but unsure.
Not sure about that one. It's pretty new. You'd think they would have it straightened out by then. A Hayne's manual may be more help.
Check this channel. He might have something helpful. ua-cam.com/channels/tAGzm9e_liY7ko1PBhzTHA.html
@@jhuntosgarage Thank you for the response ill look into it!