Love the content. I just built my first 3" high powered "budget" drone and ran into some of the same issues but in the end it flew amazing. Totally worth the struggle.😁
Alright this was a good take on making a cheap clone build. But if you want the Mr Steele confidence and performance from your quad while still making a clone here are the changes you need: 1) Readytosky clone Apex (this is the best) 2) Tmotor Velox veloce 2306.5 2550kv motors ( if 6S then choose low KV) 3) BL_Heli32 ESC and F7 FC , running BF4.3 with the supafly 5" preset a) in PID tuning tab , Throttle expo = 0.50 b) throttle mid = 0.3 4) ELRS 250Hz preset , low latency is key to how Steele flies 5) Last but not the least if your vtx isnt super clean, then use additional PDB to clean up video system power Otherwise everything in this video is going to get you a really well flying quad. 6) 8k/8k gyro -pid loop rate, Dshot600 and RPM filtering are must 7) lastly dont forget to put in Steele's rates if you want to make it exact
I agree with you for everything exept the frame ...it comes to a point that if you want to SAVE the money,you need to invest in premium frame like Apex!On the long run and abuse it stays consistant,with no issues.For whoops its opossite,if you want long lasting whoop you need to invest in good fc and good motors.
Hi nice content. I do the fault and ordered Same Motors they are garbage 😂 the Motor wires was losen and the hot glue on the shaft ist Not so god ... I changed to Amax Motors After First flight
Wow that build sounded like a giant PIA.... Sorry to hear you blew your ESC, that sucks. Made contact with those screws on the bottom perhaps? As for your question, I think it depends. I started flying a Tinyhawk 2 FS after graduating from the simulator. Once I felt that I was beginning to outgrow that quad, my first 5 inch was a quad I built. I feel that building is the best way to go because of all the learning you have to do along the way. How to pick parts, how to match things, how to solder, how the quad WORKS internally, how everything goes together. You just don't learn any of that by buying one off the shelf. So exactly in your test case, when you crash and something breaks you A) Know how to figure out what went wrong and B) How to fix it. That being said I've lately been helping another pilot get in the air recently. After flying a Tinyhawk of his own he splashed right in with a GEPRC Mark 5. By his estimation he just wanted to jump right in and buying that quad was about as much as building one on his own without the complications. Especially as you pointed out build complications, like not having the right tool or missing screws or all of those annoying little things we've all had to deal with at one point or another. If you've built a few quads already you probably have quite a stockpile of stuff, I know I do. But when you're first starting out it's a real bitch. It's been working for him so far, but then again he hasn't smashed it into the pavement yet either. I believe building is ultimately the best way to get you involved and understanding the hobby. I guess the "it depends" part really focuses on your budget. With everything costing so much more nowadays, the cost of building your own is about as much if not more than a solid RTF build off the shelf. And for someone just starting out all of those "hidden costs" like tools, irons, extra screws and wire add up and making building in most cases the more expensive option. And I get some people just can't afford that, especially when you factor that getting into the hobby requires a decent chunk of change when you factor a radio and goggles. Even "cheap" radios and goggles still add to that bottom line and only serve make the cost higher when you realize you need to upgrade to something better.
No contact with the screws because I replaced them for the right length. Turtle mode after a crash and it probably popped a fet. I’ll replace with the Mambo 40a ESC and it will be rock solid.
Those jehmcu expresslrs rx are pretty bad qc. I bought two of them. Neither worked. Looked at the boards under a magnifying glass. Capacitors and resistors were misaligned all over the place and touching each other where they shouldn't.
I think AliExpress has good parts & prices for fvp drone. I bought almost all of my parts from there. For e.g Tmotor L1604 motors x4 for $36. Geprc cinelog35 V2 analog elrs for $169. ISDT PD60 for $10.20. HGLRC M100 GPS for $9.30 etc
Just the basics. A snag placed diagonally across the bread with onions on top and tomato sauce. Although unfortunately Bunnings have mandated the onion to go on the bottom of the snag now because of Health & Safety.
Putting some extra hours to build sounds not an issue, but is it cheaper? Like what's the take off weight? How does it perform compared to a BNF of same price?
If you'd like to know what parts I used, here they are!!! ✈️ Frame ► s.click.aliexpress.com/e/_AFEms7 🎛️ Flight Controller ►s.click.aliexpress.com/e/_AdcFoJ ⚙️ Recommended ESC a) s.click.aliexpress.com/e/_9vBhIb b) s.click.aliexpress.com/e/_AXaesF 🛞Motors ► s.click.aliexpress.com/e/_A0yD4J 📡 VTX ►s.click.aliexpress.com/e/_AE7psr 📶 VTX Antenna (Select RHCP & RP-SMA) ► s.click.aliexpress.com/e/_97YiIX 📷 Camera Use This one: ► s.click.aliexpress.com/e/_AezrQ7 The One I used: ►s.click.aliexpress.com/e/_AkeSKn 🕹️ Radio Receiver ►s.click.aliexpress.com/e/_97fD7N Additional Parts Needed
🔩 Frame Bolts x 8 (m3 x 12mm) ►s.click.aliexpress.com/e/_ALOADN 🔩 Stack Bolts x 4 (m3 x 22mm) ►s.click.aliexpress.com/e/_ACmQ7h 🔩 Motor Bolts x 12 (m3 x 5mm) ►s.click.aliexpress.com/e/_AqUBT9
Learn to Build a 5" Freestyle FPV Drone 🎓 www.darrenfpv.com/buildmasterclass-5freestyle
Love the content. I just built my first 3" high powered "budget" drone and ran into some of the same issues but in the end it flew amazing. Totally worth the struggle.😁
me 2
Wheres the cascading stepdown regulator?!?!?! steele shouldnt be in your title without it, please correct this.
😂
🤣
Alright this was a good take on making a cheap clone build.
But if you want the Mr Steele confidence and performance from your quad while still making a clone here are the changes you need:
1) Readytosky clone Apex (this is the best)
2) Tmotor Velox veloce 2306.5 2550kv motors ( if 6S then choose low KV)
3) BL_Heli32 ESC and F7 FC , running BF4.3 with the supafly 5" preset
a) in PID tuning tab , Throttle expo = 0.50
b) throttle mid = 0.3
4) ELRS 250Hz preset , low latency is key to how Steele flies
5) Last but not the least if your vtx isnt super clean, then use additional PDB to clean up video system power
Otherwise everything in this video is going to get you a really well flying quad.
6) 8k/8k gyro -pid loop rate, Dshot600 and RPM filtering are must
7) lastly dont forget to put in Steele's rates if you want to make it exact
^ This
And power your camera from the VTX
I agree with you for everything exept the frame ...it comes to a point that if you want to SAVE the money,you need to invest in premium frame like Apex!On the long run and abuse it stays consistant,with no issues.For whoops its opossite,if you want long lasting whoop you need to invest in good fc and good motors.
@@miscosas no clones are trash and stealing. Stop condoning it.
Real ones know.
Hi nice content. I do the fault and ordered Same Motors they are garbage 😂 the Motor wires was losen and the hot glue on the shaft ist Not so god ... I changed to Amax Motors After First flight
yep - that's a good choice!
Wow that build sounded like a giant PIA....
Sorry to hear you blew your ESC, that sucks. Made contact with those screws on the bottom perhaps?
As for your question, I think it depends. I started flying a Tinyhawk 2 FS after graduating from the simulator. Once I felt that I was beginning to outgrow that quad, my first 5 inch was a quad I built. I feel that building is the best way to go because of all the learning you have to do along the way. How to pick parts, how to match things, how to solder, how the quad WORKS internally, how everything goes together. You just don't learn any of that by buying one off the shelf. So exactly in your test case, when you crash and something breaks you A) Know how to figure out what went wrong and B) How to fix it.
That being said I've lately been helping another pilot get in the air recently. After flying a Tinyhawk of his own he splashed right in with a GEPRC Mark 5. By his estimation he just wanted to jump right in and buying that quad was about as much as building one on his own without the complications. Especially as you pointed out build complications, like not having the right tool or missing screws or all of those annoying little things we've all had to deal with at one point or another. If you've built a few quads already you probably have quite a stockpile of stuff, I know I do. But when you're first starting out it's a real bitch. It's been working for him so far, but then again he hasn't smashed it into the pavement yet either.
I believe building is ultimately the best way to get you involved and understanding the hobby. I guess the "it depends" part really focuses on your budget. With everything costing so much more nowadays, the cost of building your own is about as much if not more than a solid RTF build off the shelf. And for someone just starting out all of those "hidden costs" like tools, irons, extra screws and wire add up and making building in most cases the more expensive option. And I get some people just can't afford that, especially when you factor that getting into the hobby requires a decent chunk of change when you factor a radio and goggles. Even "cheap" radios and goggles still add to that bottom line and only serve make the cost higher when you realize you need to upgrade to something better.
No contact with the screws because I replaced them for the right length.
Turtle mode after a crash and it probably popped a fet. I’ll replace with the Mambo 40a ESC and it will be rock solid.
Lol sausage break that was great.
Those jehmcu expresslrs rx are pretty bad qc. I bought two of them. Neither worked. Looked at the boards under a magnifying glass. Capacitors and resistors were misaligned all over the place and touching each other where they shouldn't.
I think AliExpress has good parts & prices for fvp drone. I bought almost all of my parts from there. For e.g Tmotor L1604 motors x4 for $36. Geprc cinelog35 V2 analog elrs for $169. ISDT PD60 for $10.20. HGLRC M100 GPS for $9.30 etc
good drone, Greetings from Indonesia, good luck for the future. greetings one sky
This sausage meal looks like the real deal. You have a toast, sausage, ketchup, mustard and anything more in it? Onions and bacon, perhaps?
Just the basics. A snag placed diagonally across the bread with onions on top and tomato sauce.
Although unfortunately Bunnings have mandated the onion to go on the bottom of the snag now because of Health & Safety.
Buy individual esc's, it will cost far less in the long run to operate and fix!
blud is built like frankenstein 💀
Yep, that’s part of building from Ali Express
You shall have just.. taken an aocoda F4.. got one and its been great.. till it got wet
Lol. Everything is great until it gets wet.
I’m really liking the SpeedyBee F4 Stack
Putting some extra hours to build sounds not an issue, but is it cheaper? Like what's the take off weight? How does it perform compared to a BNF of same price?
Interesting questions - that's one I will put on a follow-up video!
Build vs Bought vs Upgraded
I have this frame coming soon its sick lol
Is this a 4S or 6S build ? There is no mention of battery.
6S, but you can fly it 4S
If you'd like to know what parts I used, here they are!!!
✈️ Frame
► s.click.aliexpress.com/e/_AFEms7
🎛️ Flight Controller
►s.click.aliexpress.com/e/_AdcFoJ
⚙️ Recommended ESC
a) s.click.aliexpress.com/e/_9vBhIb
b) s.click.aliexpress.com/e/_AXaesF
🛞Motors
► s.click.aliexpress.com/e/_A0yD4J
📡 VTX
►s.click.aliexpress.com/e/_AE7psr
📶 VTX Antenna (Select RHCP & RP-SMA)
► s.click.aliexpress.com/e/_97YiIX
📷 Camera
Use This one:
► s.click.aliexpress.com/e/_AezrQ7
The One I used:
►s.click.aliexpress.com/e/_AkeSKn
🕹️ Radio Receiver
►s.click.aliexpress.com/e/_97fD7N
Additional Parts Needed
🔩 Frame Bolts x 8 (m3 x 12mm)
►s.click.aliexpress.com/e/_ALOADN
🔩 Stack Bolts x 4 (m3 x 22mm)
►s.click.aliexpress.com/e/_ACmQ7h
🔩 Motor Bolts x 12 (m3 x 5mm)
►s.click.aliexpress.com/e/_AqUBT9
I've ordered the same VTX, is it good or I might have issues with it ?
@@nikolazagorski5655 you should be fine, didnt miss a beat for me
Great video and Luv your budget build.You got a new sub!
Change its to 190USD or 260AUD :/
5% of my audience is Australian and 80% is American… Sorry mate
Wait, AliExpress actually send stuff?!
Yeah, It's banggood that doesnt send stuff
whoooot such cheap FC Stack... whats wrong with it?
The ESC is shite
What battery do I use 🤔
If you do a 4S use a 4S 1800mah, for a 6S use a 6S 1300mah.
Australia is limited with battery suppliers so mostly CNHL or Tattu
Is this antena get the job done?
Which antenna?
I’d just order btf iFlight Nazgul and spend the time for travel/flying :-)
Love your channel man
Thanks Mate. Glad you are enjoying it?
What was the liftoff mass
Same as most other 5” around 700g
Please don’t buy knock offs man. Support the people that keep the hobby going, not the thieves grifting that don’t care about us.
Funny, I think I mention this very early on in the video
@@DarrenAllatt you do, I’m just commenting that even for the “budget”I don’t think it’s okay 🤷🏼♂️
No offense I tried to not be rude whatsoever.
It’s just something that I hate seeing, bad for the community imo. That’s all.
@@mhoovair89 all good!