Відео

That rubber smell is the cheep rubber gasket on the bottom of the unit. To resolve the issue I’ve replaced mine with a silicone gasket. Got a sheet of silicone through amazon cut to size👍

@braapyolefart4865 The one that the metal fuel line passes through?

@@Thinkflite yes, replace it with silicon that will most definitely get rid of the burning rubber smell. The burn chamber gets real hot and the rubber breaks down, it actually gets hard and brittle. That’s my experience

@@braapyolefart4865 manly thanks 😊

That's a good tip! Thanks you're sharing. Was the conex filled with stuff or was it empty?

@@ChilliesWorld oh no it was completely empty, it’s about 8000 pounds? And the way the thing wanted to slide back-and-forth on the railroad ties so easily, if I would’ve had anything in it; would’ve shifted it all over. I bought mine off Amazon and made sure to comment and photos, so people buying it realize they can pop.

Also, I used a pneumatic bottle jack, a lot easier than pumping by hand. If I had to do it again, I would do a pneumatic toe jack.

Thank you for watching!

It only shuffles one deck. I don't know of any that shuffles two decks.

I love that idea! Never thought of that. Thanks so much for the tip! It will help me make better videos.

I appreciate the advice! I'll definitely check out James Condon's videos.

For 2020 and up it needs to be hard code by a professional or expensive equipment

You're welcome! It's the little things that help, right?

It's what I had on hand but I've heard the metal foil tape works better.

I don't know for sure because I haven't tried it with a Ford Ranger.

Thanks for watching and replying!

Thank you!

Thank you so much for the compliment!

The greenish tubes are the airbags. They can be removed ,and you can use airbag resistor simulators to avoid getting an error code. The seats that were removed had shoulder seatbelts anchored to them. They are not attached to the walls. I don't know if it could be run from shore power. My guess is no because the van runs off a 12 volt battery and shore power is 120 volts to 240 volts. But I could be wrong. Check out www.fordtransitusaforum.com This site for Ford Transit owners has great info and very helpful members that can guide you in the right direction on that.

Hey I saw you tried type 1 and 2 communication. I see it's a 2014 Ford Fiesta, how many times did you turn it on and off while programming it? 2017 and older should be 4 times while 2018 and newer is 8 times. That's the only thing I can think of.

I went with 3 inch because that's the smallest size duct work and vents I could find. 2 inch may be too small. How many crates do you need to get air to?

I used left over plastic trim that I cut into squares and used silicone to keep them in place before I laid the foam boards on top.

The foam boards that I put in for insulation work perfect. Less work and time involved. Once I put the vinyl flooring on top, I didn't notice any of the voids underneath. Hope this helps! Thanks for watching!

You're welcome! Thanks for watching and commenting!

Happy to help

You're a tool and just that. Now go troll someone else

@@ChilliesWorld if you don’t know the difference, you might need a few classes yourself. This video and the description is like saying “the best wat to drive a car” then showing a picture of a wheel bearing. No trolling needed, just stating the obvious

@@DinorwicSongwriter low key I make misspellings and grammatical errors on purpose. It triggers some to comment about it which drives up the algorithm for my videos. Thanks for replying!

That's faster than most dealers. I agree it is not the greatest shuffler. I used to deal at the Venetian in Las Vegas and the shuffle master and deck mate shufflers are by far the best out there. This shuffler is good for those that don't want to shuffle, don't know how to shuffle, or not as fast as a professional dealer. Using 2 decks in rotation makes it so there is no downtime waiting for a person or machine to shuffle, just like a casino. But be warned this shuffler needed to be fixed before the 1 year warranty was up. And The person who owns this table, said the customer service was horrible when trying to get it fixed. I no longer can find it on eBay or Amazon, so they may have went out of business. Poor product + poor customer service = no business

@@ChilliesWorld I forgot to mention that I was a blackjack dealer for almost 10 years. And a majority of the time I worked at 1 specific casino where we hand shuffled 6 and double deck. So I am a lot more experienced than even most dealers. But still an average person is probably what 2x slower? So 40-50 seconds for a wash and shuffle, 20-30 seconds no wash?

@@wesch6354 yeah about 30 seconds with no wash sounds about right for the average dealer. After dealing for so many years and taking pride in my work, I really appreciate fast efficient dealers. Whether it’s on a blackjack table or a poker table.

@ChilliesWorld I thought the door popped open when it was done with the shuffle thus getting in the way. But after watching videos on the shuffler I see it doesn't. So yeah using 2 decks like in the casino would make the game flow faster. Especially worth it if your home game had a rake wink, wink.

@@wesch6354 the lady who runs the game doesn’t charge rake . . But she does accept tips, and wants to get out as many hands as possible.

Exactly! Way better to take the time and effort now to prevent it from shorting out, before installing everything else.

It's been over 2 years and still no problems with my LED lights

That's a genius idea! Never thought of doing that. I'll have to add this to my bag of tricks. Thanks!

$800

I prefer no drinks on the table as well. But having an option is nice. The lights are a must for helping see the cards better. On my next table I'm adding charging outlets for people's phone. Hope to have that video done by end of September..

@@ChilliesWorld Now your Talking! The USB ports is that Extra that everyone loves. And when you go to a Casino without it, you feel like that place is Not taking care of customers. Then you start finding other things to Bitch about Rake lighting etc.

Here’s a link for the jack lug ebay.us/iDWHeR

Thank you!!

@@winstoncarrington9891 I’m happy to hear it helped! Thanks for watching and commenting!

Thanks for watching! Hope it helps!

Yea it's bad. That's why I just turn the fuel line off and let the generator run until all the gas gets used up in the carburetor and shuts itself off. It saves me from having to clean it too much, compared to when I leave gas in it.

The little piece may be gunked up making it hard to unscrew. Try spraying carb cleaner into it to loosen it up.

I'm not sure I understand the question.

It cost about $800

Thanks for watching! I appreciate the feedback and comments!

I'm not sure if it would. I would contact ford and ask them what the keypad part number is for your year/make/model

@@ChilliesWorld thanks I did and waiting for the dealers reply

I parked my van on a flat surface and kept trimming the HDPE, checking with a level each time until it was perfectly level. The 6 degrees refers to the angle I set my table saw blade to when cutting the HDPE to make it level for my brackets. Hope this helps!

@@ChilliesWorld Thank you! That definitely helps. I wasn't sure about the level application because nothing is truly "level" in a vehicle given the surface it's sitting on and the the variable air pressure across the 4+ tires. Thanks for the tip though I will definitely try this install application on my Shuttle Bus conversion.

So after you put in your 5 digit code, does it blink rapidly 3 times or one time?

@@ChilliesWorld yes i've got the van into program mowed with all of the remotes, sounding the tone, the keypad, blinks three times but for some reason is not programming? Thanks for reply

And after you heard the chime, confirming the keypad and the remotes, did you take it out of programming mode before testing the remote and key fobs? At the 2:30 mark it shows how to take it out of programming mode

@@ChilliesWorld I never got it to chime for the keypad only the remotes, unfortunately. Still appreciate your replies and making this video but I think I'm just going to pay the price and ticket to dealer. The directions that came with my unit are different from yours on the video. I have tried both ways and can't get it to work with the directions in the box or the ones in the video. Thank you very much for your time!

$1,642.41 was the total cost of materials.

@@ChilliesWorld thank you!

Yes, I actually parked it in the middle of the road and used a level on the floor to make sure it was level both ways. The bad news is once you start traveling you never park on anything level. 🤦

If you go back and watch the video, at 1:02, you can see that underneath the patches there are M8 metric nuts that are fabricated into the build. That’s what I used to attach the roof rack to with M8 bolts.