Відео

Interested in the 3d printed stand.

And and ihmmm and hmmm ahh spin out hmm uhh

Can you PLEASE NOT DO THIS AT WORK?!!! it’s bad enough you take 27min to get to the point and admit your mumbling ffs

The best body for these cars is the shortest and lightest one you can get. Aerodynamics doesn't really play a role at this size.

I just got my mini z and went to replace the t plate with a 3d printed one. The factory screws are unreasonably tight. I plan to change them all out to hex head. However, simce they are all phillips in the car, i need to get them out. What size is a proper phillips for the mini z's #00?

Yeah so I use alcohol and a spot of toothpaste for run in with one AA battery for 5 min.. far better results as the grit in toothpaste polishes comm..and seats brushes better,, trick from reedy motors we did in the 80’s

Thank you, your videos have been so incredibly helpful! Do you have any recommendations on how many kingpin shims to run? Like how many above the steering knuckle and how many below. The manual says 1 shim above the steering block and 1 shim below but I was wondering what most guys do for a race setup chassis. Thank you!

On power over steer could also be a diff that is too loose causing the inside tyre to spin 'diffing out' and the car spins out or too tight causing the outside tire to break traction and causing a spin out...

What about box stock but with +1.5 offset wheels front & rear plus softer racing tires. than, thicker and thinner T plate in addition to the wheels & tires compared to box stock (I have a amg gt3 rwd readyset )

On a rc caster angle is useless because the servo is keeping the car straight. The force of caster angle is not strong enough to correct misalignment of the servo and steering. USELESS you can implement a steer by wire system, which you can drive the rc depending on the force feedback.

Hi there! I'm an engineer, just wanted to chime in on the aerodynamic drag topic, you can basically ignore that as a factor in Mini z Racing, you aren't going to do anything to have a meaningful change in driving performance at the speeds these are capable of. Just as an example, if you took a car with one of these racing bodies and raced it against another that magically had zero drag, it will contribute to about 2% less air resistance than your standard mini z if your speeds are under 15mph and about 4% at 30mph. Remember that we are talking about the total delta of full air resistance vs none, you are probably looking at a total difference of under 20% for all these modern racing bodies. Considering that your rolling resistance is probably over 90% of your total resistance at these speeds, you can quickly see how aero just doesn't matter with this, you would be chasing less than a tenth of a percent of change in your top speed.

kind of a click bait title - just add "is practice" in the title. I came here looking for upgrades suggestions because I'm going shopping in Tokyo, kind of wasted my time a little bit, but not a big deal

Great video! All your kids are very helpful. Just want to know if taking off the large capacitor makes the motor faster. Thanks.

I really like your advice on switching from a stock-ish Mini-Z to a custom chassis without wasting too much energy on upgrading Mini-Z. I have one important question though: Where did you get your Audi Body? I absolutely need one 😀

Thank you!

Love the videos brother! You got any more mini z videos in you? I just got into the sport and got the large 96 track and I need to learn from the best.

Very helpful.🤔🤔

Great video. We need part 4 lol

Didn’t review the AMG?

is it too late if i already had run the motor with one set of battery? thanks

What front wheels are these?

Do you have links for these upgrades?

love the detailed info !

I have a question, does the kingpin flip do much of a difference in stock class because i did it in open class and it didn’t make much difference

hi please can you help me 🙏 will this body fit in current chassis and L ( 94) Narrow ? thanks

Appreciate all ur videos. Just started a new racing league and these are great … Also I peep ur AP!

how long should this take with AAA batteries?

How soft or hard the T plate should be and how it’s gonna affect the driving?

One of the best explanations as to why you "run in " a brushed motor ....enjoying the content, I would love to see some racing pal but in the mean time have a Sub

how did you set the receiver and esc on the body? Did you use glue? does it stay put?

On your main youtube channel at the top, the banner, I see a McLaren which I have the same one. Would you be willing to share what offset of rims with tires you have on it? They look like PN Racing Mini-Z 2WD Machine Cut 10 Spoke but I am not sure if they are F1, F2, F3 and R1, R2, R3 AND Love your videos, learning a ton and practicing even more. TIA Keep up the great videos!

👍👍

Como pongo el set up de la parte de adelante se va chueco mi carro en alta velocidad

Hola que bateria me recomiendas para mi glr

im sorry to say but what a bad video.. no explaining why youd use what part. you just yell what one part we need. then what others you also put on it..

Is that xpeed V motor by kyosho ?

This dude is a boss....

Ah, the memories. It's been about 20 years since I raced 10th scale touring, and I'd forgotten all about running in the motors under water. We also use to just dip them in water running for a few seconds to clean them occasionally. As for drying, we also used compressed air (gently) to speed up the drying process. Thanks for the info!

What is that white tile/board/thing in most of your videos?

You should do a set up guide on the GLF one or at least give your thoughts on it. Also, are we going to see a video on tires anytime soon?

What about putting a 1mm washer under the back screw on the T bar of the car? That will lower the droop and will not affect the preload at all.

Your so correct when it comes to the front springs collapsing I know that when I'm entering a corner and I give initial steering the front spring seemed to collapse quickly so my solution to that was to slow the curve down on the radio by 15% so the spring doesn't collapse all at one's it collapses slowly. At least that's what I had to do to my 1/12 scale😅 and I learned that from one of the yokomo drivers

Confused - where is the content? Yt send me to a Kyosho Vido next ... Thanks!

What’s the standard Mini-Z track width? And what’s the track width with wide vs narrow front, and with different offset wheels? Thanks!

And the amg?

Great video. Are you from Denmark. ??

Still waiting on transmitter setup!

When will you post more videos! Super helpful to us newbs out there

Hi, i appreciate your videos how they are detailed and how you breakdown everything. Im a newby is there a simple setup you can recommend to start with a balance handling for me to try for a box stock setup. Thank you