Відео

You can’t beat it! And when compared to the commercial versions, Turfmaster and Commerical 30, it’s so much easier to operate and turn. I am a big fan of the Personal Pace. Thanks for watching and commenting!

Hi. I got them off Amazon. Here is the link… amzn.to/3ZAiDOw Best of luck and thanks for watching!

No reason. Honestly at the time, I didn’t even consider it an option. Lack of awareness probably. You going for it?

I like 4 to 4.25 on most mows. Sometimes I do the parkway area by the road at 4.25 and everything else at 4. The heat from the road and sidewalk heat up that section too much sometimes. So, I let it be a little taller.

Maybe adjust the throttle or new OEM carb? It could be idling to low of RPM’s. In my experience, sometimes cleaning a carb isn’t enough. You just have to get a new one. I like OEM for this. I think this is the one… amzn.to/3WXBNxX Otherwise, it might be time to FB Market and look for a replacement. Hope this helps and good luck!

@@theSuburbiaDad Thank you for the reply. I found it’s puffing air out the intake. So maybe valves or bad head gasket. I’m taking it down the road to a local small engine shop. Thank you again.

Thanks for watching!

I used the belts that were there. It wasn’t an issue at all. Thanks for watching!

After it’s replaced the code needs to be cleared. Or for me at least it did. It didn’t come back after that. Hope that helps!

@@theSuburbiaDad I’m sure they tried to clear the code but they said somethings wrong with the wiring. I don’t know if that’s true true

@616mickie strange. Mine worked perfectly after I cleared it. Maybe AutoZone can clear with their scanner for you?

Great idea! It is a great overall machine. I was always a fan of the side discharging with it. Thanks for watching and commenting!

Thanks for the feedback and watching! It’s noted.

Usually 4 to 4.5. Taller grass is definitely easier to stripe. Rarely under that range until Fall. I don’t think my ground level is smooth enough for under 3. I would probably blast the high spots out the side discharge. 😂 Thanks for watching!

Blades make such a difference! I’ve never tried Gators. I’ve heard nothing but great things about them! And I agree about a jack. I’ve been using a Ballard V2, so fast and no 💩 on my leg. 😂 Thanks for watching!

You’re a unicorn! 🦄 I’ve had a TurfMaster and Commercial 30, and I still like the handle bar / controls more on the Timemaster. Cut quality seemed just as good as well. The commerical models are not the most comfortable to use on your hands! Thanks for watching!

@@theSuburbiaDad I prefere the personal pace. Being diabetic with neurapathy I can set the pace I want, basically better for me. Don't know what the unicorn stuff is about but to each their own I suppose.

@mrgreen2769 a unicorn object is something no one ever finds or is hard to find. Your stock pulleys going strong, it’s a unicorn find! Love the personal pace. I wish that was in the commerical line!!!

I see you Canada! Thanks for watching.

Nice!!! I got stickers in the truck for that reason!

It depends on how hard the soil is. You want to get 2 to 4 inch plugs. So, maybe start with no weight, then had blocks as needed. Hope that helps!

Me too. 😆 Don’t do what I do. Thanks for watching!

I think I commented on your other comment with the information. Is that was not you, let me know! Thanks for watching.

Agree 100 percent. But if you don’t have one, here is a work around. Thanks for watching!

Here is the one I got…. amzn.to/3Xvxqeu It’s no longer available. I feel like people have used this one… amzn.to/3VOwEYH It looks identical to what I have. If you try it, let me know if it fit! Hope this helps! Thanks for watching.

Garage is a mess nowadays! I don’t know if I could find any tools anymore. But thank you and thanks for watching.

Also, maybe heat shrink the wire connections...

Yeah. Probably would have been a good idea! Thanks for watching!

Agreed. That would be ideal. Thanks for watching!

😂 💪

What was your solution? Impact drill? I hope you got it!!!

Lost me on this one. 😂

I’ve thought about it! I know some companies make a deck spray. I’ve never used one though… yet. Thanks for watching and commenting!

PPE is always recommended! Thanks for commenting.

😆

It makes quick work of lots of blades fast!

Nice!!! Thanks for watching.

It sound like, maybe, the reel is too close to the bed knife. Adjust the screws on either side until it spins freely with as little gap as possible between the knife and reel. That’s my best guess. When I’ve had clunk sounds that was why. Hope this helps!

I’ve never had an issue with mine. Still on since the day I did it.

I forget off the top of my head. I think it was like outside wheel to outside wheel. There website and recommendations on it. Hope this helps!

I suppose it would depend on the engine you have. It should be in the manual for the Kohler and Kawasaki. Hope that helps! I’m sure by now you found it. Thanks for watching!

😲 That’s why I changed it out right away. I bet it sounded horrible!

There are a million ways do to anything and get the same result. So, if it works, perfect! Love the collection you’re building. Keep it up! Thanks for watching!

If you have the space to store a ride on, I would ride. 😆 Are you talking about the Edge? Timemasters are nice. I swapped my pulleys out right away for the Exmark ones. It’s a common fail point. The cut is sweet though. I always side discharged. I think it cut better shooting the clipping out the side. But, if you can ride, I’d ride. You might consider a small stand on? I have a 36 stand on and it’s sweet.

It’s a great mower! Cut is clean and it’s a nice ride. Thanks for watching!

I don’t know what that means. Clarify for me.

@@theSuburbiaDad professional reel mowers has goven cuts per meter or foot/inch. That means how many times reel knifes will meet bed knife during 1 meter ride. The higher the less ribbon effect you will see on the lawn when cut low. I will be gratefull if you could measure wheel diameter or circumference and how many times reel will cut during one full wheel rotation.

It’s a nice relaxing ride! 😎 Thanks for watching!

It’s nice to be able to make one less trip! If I used the bracket, it would stick out further than I wanted. So, I modified the install slightly. 😆 I was thinking particularly on my 36. It needs to stay that to get in and out of gates. Anyways, thanks for watching as always!

It’s makes quick work of it for sure! I feel like the sharpening disk has lasted a long time. I did flip the disk over already, but it goes and goes. Hope your doing well! Enjoying the videos you’re getting out there.

@@theSuburbiaDad Yeps I'm still using Flap disk like that setup you got there✔️💯

@@bigsonslawncare flap disking is great too! I was a ninja with those things. 🥷

@@theSuburbiaDad 🤭🤣

I’m blessed. Thank you.

You don’t even know you need it until you see it! Thanks for watching and commenting.

Hi! Here is the kit I used… amzn.to/3PASkDX As for time, basically until it sounds like it is spinning smooth. You can hear it the difference. Hope this helps!