Відео

1st. I would have a talk with the hacker that installed the CF. 2nd after a power loss you have an inherent time delay to prevent short cycling in funky power situations.

just got a pair lol

I like the bucket Idea.😂

Hate going out & "Fixing" another companies work, when they billed/made a shitpot full of $$$ for all the new stuff they replaced. Then when you go out & fix the shitty install/repair the office manager then gives you a shitty look when you have to charge for a proper fix. saying "why did/should you charge us so much? I just paid the other company thousands of $$$ for All this new shit. Then we spend more unbillible time explaining what/why we did to fix & show bills/repair time & cost!!!!!

How long did it take you to finish all the units ?

Great video . That plane was huge lol

Sorry need chain temperature centígrados Fahrenheit

I use my 87 Max along with the amp clamp to find shorts like that. On amps, switch to 'MIN MAX', and it will capture the high current in a split second. Check to see if your meter can do that.

Less connections are less likely to have a leak on your end, affecting your pressure test. Fieldpiece only looks at the low side for pressure testing.

Does it go back together easy or can you risk bending them on eachother?

You only checked amperage on a single phase and recommend a new motor. Recommend a coil cleaning on a system you thought was over charged. Then didn’t even check superheat sub cool. Not too far from the previous contractor as far as thoroughness

Ryan, great videos! Maintenance mechanic here ,just starting a building maintenance position ,concentrating hvac. Onthat machibe your working on with the coils in the middle of the machine. What's the vest way to do setups like that?

Just got this today worth every penny!

Extra charge new Plenum rated wire line set here in Texas.

Careful around compressor soft-plugs on a hot compressor! Camera angle seemed to be in-line with the plug. Not a big fan of these latches LOL. i'm not a big fan of Lennox. This surly took life out of an LG.

I have found that carrier RTU's don't run the condenser fan with a Y2 call alone. I don't know why they do this except to cut cost. At least the tech didn't just bypass the high-pressure switch. I kinda like the manual reset switches. Let's you know there is a problem, but they can be a nuisance.

Exelent job sir! The SH is probably not accurate. I had some time to play so I did some testing on a York adding liquid line ports. Liquid line ports were 30 psi lower than the discharge ports. I had heard it could be anywhere from 0 ~ 35 psi, there's nothing like actually seeing it. I don't know why manufacturers are so determined to put ports on the discharge line. The only way to check charge is to weigh out and in, a time consuming process. Oil on the condenser maybe from brazing in the filter-drier.

Omg this was a close call! 😮 this was a good one! No air flow and no limit means it's an oven 😂

If I can get a year out of boots that cost me $100, I'm happy with that.

Decided I wanted to learn more of what I don't know. I wear a Caterpillar 2nd shift work boots. Because of the electrical isolation. with cat boots you are going to need to put about 25 miles on there boots before you brake them in.

I stick to cowboy boots now man was tired of replacing boots every 6 months

The greatest technicians have crappie tools.

Redback Boots out of Australia, last about two years but that's better than any other boot I've had.

Sad that seagulls are protected

Are 2 guys recommended for blower replacements I always go alone 😂 and man sometimes it’s a pain getting it up there

Can you educate me on what is wrong with that blower Motor you want to replace?

I have to do this by myself tomorrow

Keep a tennis racket in your tool bag. It works great on sea gulls!

That tee though …beauty 🤘

Tried a lot of brands from the cheap one to the Redwings all last about a year , now I try to find the lightest one I can find that are waterproof and safety toe

I think troubleshooting is easy in HVACR

Some of those filters you pulled out look brand new. I'd be concerned something's wrong and the unit isn't working.

He couldve just factory charged through the liquid line them fired up after without even checking pressures to see that his blower was going backwards smh 😅

Not an HVAC guy but I know a little bit. You must be one of the rare ones, out of the 5 different channels yt recommended me today you're the only 1 that knew what to even do. Thanks for knowing your stuff

Why do you did you put back that cleaning drain pipe you should have let it drain down to the roof it'll get dirty if it's straight up pipe for the drainage

I’m not here for a leak check, as I’m looking for leak, going to charge for leak check

Love how the tech…. Not sure but going to recommend this and that.. what’s a couple hundred dollars if it’s not yours.

I should of brought my pew pew 😅

You’re a good tech. Good job man

How you make bypass flug . Or how I can buy it Sir?

How can I be a service tech like you man my company doesn’t teach me anything

Instead of removing the covers, use your voltmeter and check for voltage or continuity? Lol

What was that thing they were keeping cool? The thing with the sprinkler going on it?

Nice Work Ryan!

@18:34 "no cap" sounds like what these young kids say these days

Good job 👍