This has been really useful, thanks a lot. All I would add is to use 1/4 inch drive sockets (as you did) because 1/2 inch are too bulky to fit through the channels without a lot of messing about.
I really appreciate the work you do but it would be better if you start with disconnecting the battery to avoid the signs of faults on the car board .thanks
Hey. Had the same issue and your video help me change the bad egr valve. Also i wanted to clean my hyundai throttle body but i cannot locate it. It goes somewhere under the egr valve. Your input will be gladly appreciated.
thanks to watching your video i found out were my sqealing noise was coming from.....the two nuts on the egr body were loose to the manifold .......typical garage fook up....
Hi sir.. good day.. just want to ask about the nozzle from the engine that is connected to the third hose in this video (10:52).. the noozle just above the oil filter?
Thanks, I must confess I have no idea what it was - but it had to be unplugged , hahahhaa. I am not a mechanic, just someone who isn't afraid to take stuff to bits. ( I think it was the fuel pressure sensor )
Phantom Video thank u for your response i just found the location of the sensor. My car is statling at low rpm when i am light throttling and try to figure out what is happening.
Just a guess, unplug the Mass Air Flow Sensor ( the electrical clip ) on the MAF, see if it runs better. You will need to delete the error code with a code reader after you have done it. Try that.
Just after some info off you ,any throttle and egr is reading -100 when not on throttle its any where to + 100 doe s this mean the egr isnt working ?cheers
Hi i have a question about the number codes of the fuel injector, how do i know if one of my injectors is the 1st one?? Or does it have a number codes?
Modern day technology is stupid. Even though my EGR valve has never caused be problems ive cleaned it out a few times to prevent any future problems. It doesn't get too coked up but by the time ive cleaned it up the sink is black. I use Mr Muscle to clean it out and a Dremel. What blocks up EGR valves is short journeys and rubbish fuel. My Dad's Kuga went into limp mode because of a blocked EGR.
Hi just tried to do this but got bogged down whit the bolt on the bracket underneath the egr, socket would not connect with it, is it a size 10 or 12 and how did you do it.
It's the same size as the other bolts from memory Andy. Try this, just push a small piece of insulation tape in the socket and then push over the nut head, see if it grabs it.
Super filmik :) Dzięki za pozytywne nastawienie do roboty. Pozdrawiam:)
This has been really useful, thanks a lot. All I would add is to use 1/4 inch drive sockets (as you did) because 1/2 inch are too bulky to fit through the channels without a lot of messing about.
I should have read your comment before attempting to replace the EGR. I lost a 1/2 socket 😅
I really appreciate the work you do but it would be better if you start with disconnecting the battery to avoid the signs of faults on the car board .thanks
Hey. Had the same issue and your video help me change the bad egr valve. Also i wanted to clean my hyundai throttle body but i cannot locate it. It goes somewhere under the egr valve. Your input will be gladly appreciated.
Great video thanks for sharing .
Great video looked very awkward due to the confined space 👍
Cheers for the video was a great help 👍
It seems to be the same EGR for KIA Carens. I will try to remove and clean it.
Thank you.
thanks to watching your video i found out were my sqealing noise was coming from.....the two nuts on the egr body were loose to the manifold .......typical garage fook up....
Can you explain if there is a PCV valve in this Tucson?
Can you show me where do you pump for the desil
Hi sir.. good day.. just want to ask about the nozzle from the engine that is connected to the third hose in this video (10:52).. the noozle just above the oil filter?
How can i get out the water tube in the cylinder head that goes to the egr container?, is near the oil filter
Hello! Great video! Can you confirm if the egr valve for your Hyundai is electronic or mechanical?
The egr is electronic with solenoid.
Hello very nice video. At 4:20 minutes is that the MAP sensor you unplugged?
Thanks, I must confess I have no idea what it was - but it had to be unplugged , hahahhaa. I am not a mechanic, just someone who isn't afraid to take stuff to bits. ( I think it was the fuel pressure sensor )
Phantom Video thank u for your response i just found the location of the sensor. My car is statling at low rpm when i am light throttling and try to figure out what is happening.
Just a guess, unplug the Mass Air Flow Sensor ( the electrical clip ) on the MAF, see if it runs better. You will need to delete the error code with a code reader after you have done it.
Try that.
I cleaned the maf but still does it. I will try your suggestion and see. If it runs better i probably need a new one or better cleaning i guess.?
yes, if it runs better - get a new one I think. or borrow a working one from another car if you have a friend with one.
Just after some info off you ,any throttle and egr is reading -100 when not on throttle its any where to + 100 doe s this mean the egr isnt working ?cheers
your egr problem did it also kangeroo intermitantly on low rev's around 2,500 revs??????
No Kangarooing, sorry.
Did you ever find out what this problem was pal thanks any help please
i wish i would have put a rubber on my pipe years ago, i wouldn't have had 8 kids now, i bloody dread christmas.
Hi i have a question about the number codes of the fuel injector, how do i know if one of my injectors is the 1st one?? Or does it have a number codes?
Modern day technology is stupid. Even though my EGR valve has never caused be problems ive cleaned it out a few times to prevent any future problems. It doesn't get too coked up but by the time ive cleaned it up the sink is black. I use Mr Muscle to clean it out and a Dremel. What blocks up EGR valves is short journeys and rubbish fuel. My Dad's Kuga went into limp mode because of a blocked EGR.
Hi just tried to do this but got bogged down whit the bolt on the bracket underneath the egr, socket would not connect with it, is it a size 10 or 12 and how did you do it.
It's the same size as the other bolts from memory Andy.
Try this, just push a small piece of insulation tape in the socket and then push over the nut head, see if it grabs it.
Phantom Video will try that thanks for the reply.
I'm getting a 299 code, turbo underboost, I used to hear my turbo whistle now I dont. Do I clean the sensor or I have to get a new turbo?
I have no idea Shimon, sorry - i'm not a mechanic.
May be a cracked turbo vacuum pipe, or check the connections?
Where is the crankshaft sensor on a Hyundai Tucson 2014
I have no idea boosie, I can't afford a 2014 car - i'm quite poor.
;-)
How do I clean the particulate filter?
I need to change my turbocharger. Do I drop my engine to remove and install it?
No just stop engine before remove 😀👍