Thanku fot that I have a OKO carb and I'm having trouble putting in the throttle cable I have a 50cc prebug Zuma and I'm building it to a 70cc did u guys us the 50cc cable??? That's my question???
People are running the 21mm carbs on bicycle engines. Are those cables long enough? From what I seen you would have to cut some of the cable cover away
@@Theruckshop I don't know how long the throttle cable is that comes with our engine kits but when you put it in the slide the cable isn't near as long as yours in the video. Your cable is six and a half feet long and I know the ones that we get ain't that long
Hi. Im using OKO carb. Bought it brand new and jet it good. Only problem is, thr slide tends to stuck. It wont stuck when the engine is off but the vacuum pulling the slide at rpms, and itll stuck again. Refusing to go to idle. Had to be throttlef again so that itl go to idle. And during changing gears, the carb will stuck at idle position, thus forcing me to grip harder to free it and it made the bike jerk for sudden throttle given. Can you give an advice on how to solve this problem? The carb is performing flawlessly except for this issue.
And i dont thinks its the cable because the throttle seem to act normal when i turn off the engine. Its only doing this when the engine is on and especially at normal ride.
so i would lube the inside of the cable since the do not come pre-lubed , we know what you are talking about though as ours does the same thing . we have sand the inside where the slide goes to smooth it. or continue to blimp the throttle before a stop . that's what I do because I'm lazy but others at the shop have sanded with a dremel and they said it fixed. its the slide getting stuck on the casting
@@Theruckshop Ok. Smooth out the slide or the housing of the slide? Anyway, itll be a risk to do so since it might also effect the vacuum process of the carb is it? Or theres no risk and just sand it or smooth it out by any means but not excessive.'
You saved me a lot of time and frustration! I didn't know the cable went in the slot of the D Slide. Happy camper!!!
Thank you for the video I really need it
Best video on this carb regarding adjusting those 2 screws for air and gas . Thanks much help. God bless you.
Thank you this helped allot❤❤❤
do you guys have or can you guys do a video on tuning the carb air/fuel idle?
Having the same problem...
Try turning on both screws 3 in a half turns out and see what happens
This dude said"scissors with clamps". How about a roach holder
😭😮💨
Awsome, THANKS. Will be purchasing this throttle cable. Coool...
Me too just installed carb wish I had this cable already
were do the hoses go now?
Did you find a video?
Even with the tension I can take the needle out to adjustment it is that normal my bike runs good but stills bogs
Can you do a video more specifically I wanted to install this myself
This atr video series covers it all. This will not get more detailed than what it already is.
Great review 👍
Thank you sir.....I just used this vid. As reference ..
Where do the oil hose go?
Thanku fot that I have a OKO carb and I'm having trouble putting in the throttle cable I have a 50cc prebug Zuma and I'm building it to a 70cc did u guys us the 50cc cable??? That's my question???
💯 julio
People are running the 21mm carbs on bicycle engines. Are those cables long enough? From what I seen you would have to cut some of the cable cover away
been doing this for 13 years and have sold over 2000 78" inch cable. for the carb 28mm and 30mm all day long
@@Theruckshop I don't know how long the throttle cable is that comes with our engine kits but when you put it in the slide the cable isn't near as long as yours in the video. Your cable is six and a half feet long and I know the ones that we get ain't that long
@@Theruckshop the throttle cable for motorized bicycle engine is only 45 inches so probably have to cut some of the sheath off
Hi by any chance do you know where I can get an 86 or 84 inch long slide throttle cable? Thank you
The cable coming out of top hits my seat not able to close all the way what do it do?
👍👍👍👍
Do the cable come the same size
Will a 3/16 ball end throttle cable fit these carbs
So i get a high rev/rpm after letting off throttle. I lubed cable and made sure I didn’t have any vacuum leaks and Adjusted cable. Any advice?
Probably an air leak somewhere
On a gy6, can you run the pcv to the vaccum on top of the carb
I would not
What the heck are all the connections on these carbs? With pink hoses on the chinese editions. Where are they to be connected?
Zachry86 please email us pic of the hose you are talking about to info@theruckshop.com
Hey who knows what size throttle cable I need for a pwk 21 carburetor someone let me know please
Hi. Im using OKO carb. Bought it brand new and jet it good. Only problem is, thr slide tends to stuck. It wont stuck when the engine is off but the vacuum pulling the slide at rpms, and itll stuck again. Refusing to go to idle. Had to be throttlef again so that itl go to idle. And during changing gears, the carb will stuck at idle position, thus forcing me to grip harder to free it and it made the bike jerk for sudden throttle given.
Can you give an advice on how to solve this problem? The carb is performing flawlessly except for this issue.
And i dont thinks its the cable because the throttle seem to act normal when i turn off the engine. Its only doing this when the engine is on and especially at normal ride.
so i would lube the inside of the cable since the do not come pre-lubed , we know what you are talking about though as ours does the same thing . we have sand the inside where the slide goes to smooth it. or continue to blimp the throttle before a stop . that's what I do because I'm lazy but others at the shop have sanded with a dremel and they said it fixed. its the slide getting stuck on the casting
@@Theruckshop Ok. Smooth out the slide or the housing of the slide? Anyway, itll be a risk to do so since it might also effect the vacuum process of the carb is it? Or theres no risk and just sand it or smooth it out by any means but not excessive.'
@@HanumanGoku it's a PWK so no diaphragm just smooth out
@@Theruckshop ok thanks.
what size needle is that?
I have a 28mm oko my problem is it wont fully open throttle
Here my same problem..am have oko 28mm carburator
Is it a special cable?
No way the lead end through the groove to seat.
You pull the cable and the wire goes into the groove and then it seats . 😊
No special cable just a normal PWK cable like all slide carbs are
Those chinese carb are goods? You got the parts number ?
76" is that to long of a cable??
I bought 2 cable bud I need one
You have to email the shop. They do not answer those questions on UA-cam.
Giclo on pWk 24?
76" Tooooooo loooooong!😡 👌
Calm, woohoo found 44"6. Cable... I'm set..