Blukman 3D/Workbee/QueenBee Pro CNC Spindle Wiring, Inverter Programing & Mach3. Series episode 10
Вставка
- Опубліковано 16 сер 2020
- Spindle Wiring, Inverter Programing & Setup to Mach3
This video will cover the wiring from the inverter to the spindle as well as the Mach3 controller to the inverter. We are also going to program the inverter for a bench test and then program it to communicate with the Mach3 controller for use with the Mach3 Software. Look below for the link to print off a “cheat sheet” I created to make programing the inverter easy.
#Slammerthehawk
stuckeyworx.com/Slammer_The_H...
Please like our page at:
stuckeyworx.com/FaceBook
UA-cam:
stuckeyworx.com/UA-cam
Etsy Shop:
stuckeyworx.com/Etsy_Shop
BulkMan3D Site:
stuckeyworx.com/BulkMan3D_Web...
QueenBee Pro Assembly PDF:
stuckeyworx.com/QueenBee_Pro_PDF
Spindle Inverter Programing Sheet:
stuckeyworx.com/Spindle-Inver...
80mm Spindle dust boot:
stuckeyworx.com/80mm-Spindle-...
3D Printed Control Box Links:
stuckeyworx.com/Control-Box-STL
stuckeyworx.com/Printed-Contr...
Manuals & Info Sheets:
stuckeyworx.com/Manuals-and-info
The links I have below are this kit as well as some of the other kits
Bulkman 3D has:
stuckeyworx.com/1500x1500-Ful...
stuckeyworx.com/1000x1500-Ful...
stuckeyworx.com/Full-Kit-750x...
stuckeyworx.com/1000x1000mm-F...
Here are some links for additional items I got:
stuckeyworx.com/4th-Axis-CNC-...
stuckeyworx.com/10PCS-4-Flute...
stuckeyworx.com/Surfacing-Rou...
Master End Mill Combination Kit: amzn.to/3ebbStL
Master CNC Router Bits Spiral Upcut: amzn.to/3dgLNIQ
Radius 1 2 3 4mm CNC Carbide Milling Cutter: amzn.to/3d6PBw9
Molex Connector Lot, 3 Matched Sets, (4-Circuits) amzn.to/3henUUv
50PCS Solder Seal Blue 16-14AWG amzn.to/32BnCDc
50PCS Solder Seal Red 22-18AWG amzn.to/3fKHM15
100PCS Solder Seal White 26-24AWG amzn.to/3eEvlmc
Soldering Iron Tip Cleaner + 60/40 Solder Wire Reel amzn.to/2CiRmdj
Liquid Electrical Tape - 4 Oz Can amzn.to/30sYN9z
stuckeyworx.com/2in1-Solderin...
stuckeyworx.com/4-Pin-Male-Fe...
stuckeyworx.com/2-Pin-Male-Fe...
I will update this list as I acquire new items... Thanks for watching and your support!!
**Exclusive Stuckey Worx only discounts for BulkMan 3D**
I am pleased to announce the following discounts I have arranged for for all of my viewers. While these discounts are not as much as holiday specials, it is something. We all know every little bit counts. Please enjoy and check back often for the updated discounts when these expire on June 30, 2021.
Codes are different for each sales channel and are not stackable.
Official Website (Bulkman3d.com):
Coupon Code: stuckeyworx0321
Use the coupon code at the checkout for a discount to apply.
AliExpress (www.aliexpress.com/store/1752067)
Coupon Code: 1RAFP5LMOAUP
Use the coupon code at the checkout for a discount to apply.
Ebay: stuckeyworx.com/BulkMan3D_Eba...
You must click through using the above Coupon Link for the discount to apply. If you do not navigate to eBay through this link the discount will not apply.
If you have any questions regarding coupon codes contact the representative on the sales channel you are shopping on (OW, eBay, AE), or you can contact the sales department at sales@bulkman3d.com
Credits:
Takin' Out the Trash by Heuristics Inc. (c) copyright 2008 Licensed under a Creative Commons Attribution license. dig.ccmixter.org/files/heurist... - Наука та технологія
Absolutly best video for Spindle Wiring, HY Inverter Programing & Setup to Mach3
I appreciated your video! I have a OneFinity set up, a 110v 2.2KW HY VFD, paired with a HY 110v 2.2KW spindle. I tried setting params using information I got out of the manual and off of the Internet. My spindle ran for about five-seconds and never up to speed. I found this video and your cheat sheet and set the params according to your instructions. It was the first time I had the spindle ramp up to 24000! However, it does that when I hit, "Run" and I can't control the RPMs with the Pot OR with my controller when I set the params for the OneFinity. This shouldn't be this hard! I'm still looking for the recipe for my particular setup but haven't had any luck. Anyway, I got further than I ever had with your info.
thanks
Hai a very good video.i see clearly now.thank you.can i used this setting for 220v 2.2kw water cooled spindel to?
Blukman ! :D
I was wondering I will be using Uccnc and was wondering if you had a video setting it up to that and not mach3 or is it pretty much the same
Good job, What interface board do you use from the PC ?
Thanks for the video very informative. I want to ask you to help me. I have a problem connecting Huanyang GT inverter wires to NVEM V2. in match 3 there is an on and off but no speed setting, please help.
GREAT VIDEO! Thanks so much for taking the time to do that.
Quick Question (I hope) - I have Mach3 running VOVUSUN V2 Motion Controller. I get my spindle to start and stop and can change spindle speeds, but it is like it is in 'Jumps'. You are increasing at 300 RPM per click and you can hear it change at each step. I am Starting at 12,000 RPM and stepping at 1,200 RPM, but it is like I have to click twice before I get an increase. Any thoughts?
And if you are in an answering mood... - How do you get the Display to show RPM instead of Freq? and how do I get the feedback RPM from the VFD to update Mach 3?
Thanks again - GREAT Video - @JDWFolkart
Great stuff. It's truly appreciated. I have a question for you.
I noticed you said you have switches set to be homing switches versus limit switches. When I home my machine all the axes do indeed home and then back off from the switches. Why when running a g-code and the switch is hit on the Z axis it's doesn't turn off? I quickly have to hit ESC to stop it. Do none of the axes stop if the switches are hit?
I also have no idea why the Z axis goes up that high during this g-code. It's only set to go a quarter inch over the material, but it goes up an inch and hits that switch.
Sorry for the late reply. I'm still learning the tools on the UA-cam platform. You can set the homing switches to act as limit switches when it is running a program. You just have to set them up in ports and pins. Set the limit switch pin numbers the same as the homing switches. Mach3 will use them as limits during operation and back to homing when you "Ref all Home".
Thanks for your tutorials, I’ve learned a lot from the videos.
I was able to do a bench test successfully like you did, I however could not vary the spindle speed from Mach 3. What could be the cause?
Completely clear out all of the settings on the spindle inverter and start from scratch. Completely zero out your spindle settings in Mach3 as well and hit “save” on the drop down menu. You should be able to get it to work after the second or third time. It’s a lot of coding and settings so it’s really easy to skip something or enter something wrong. It took me three times to get it all correct and everything working properly. Sometimes even if you do everything right it helps to just do it over again to work out the bugs...
702marine thanks for your quick response. I’ll give it a try once more as recommended and see how it goes. Thanks once again.
@@702marine I am having the same issues after following your set up instruction. the spindle will start but will not adjust in speed. I am not clear on what to do when you say to " completely zero out spindle setting in Mach3" could you be so kind to elaborate. thank you !
Sorry is I missed it. What is the electrical specs for your spindle?
Just a quick question. Will this spindle an controller work with the openbuild black box.
Thank you in advance for your response
Some questions: why pd025=1 and pd027=0.8? In my case, it leads to extremely high dangerous acceleration at the risk of destroying the spindle. A note also for the amperage of your spindle, in your case it is 2.2 amp, not 8 amp.
Thank you, very useful for me, I have the same spindle inverter.
can you help me if I use red Mach3 RNR breakout board for the wiring,
do i need to add a relay and connect to the spindle
Hey brother great review, question. I am not planning to use mach 3 at first. When I input the settings on cheat sheet everything works like yours, however I can't control the rpm with the knob like I want. What is your recommended solution
Carl set PD002 to one and your all set
I've a different inverter but i use this setting parameter, and i can control speed motor, just can control forward and reverse direction of motor. I think my inverter just receive analog input but i dont know how to give an analog input from mach 3. I'm glad if you want to help me..
Fyi i'am using inverter YL620-A.
hope you get my question
What kind of spindle and vfd?
I purchased the UltimateBee this spring 1500x1500 2.2K 220v air spindle xPRO controller. I had so much issues with the controller and getting the motors to move right I scrapped it and got a NightHawk controller. All the motors are working perfectly now but I can not control the VFD. I have gone over all the setting and matched them up to what seemed to be the best choise and moved the jumper. still, the spindle will not turn. I am hopping someone out there will be able to help me.
Hey thanks for your helpful video! So I’m setting up my 2.2kw spindle 110v from bulkman and for some reason my spindle is apparently maxing out at about 14,000 rpm on Mach3. Like I can take the number higher on the computer but the spindle doesn’t go any faster.... it’s supposed to be rated for 24,000rpm. Is there a setting somewhere that’s limiting it that I need to set to the max rpm or is mach3 just reading the rpm wrong? When I turn control of the spindle back to the CFD panel (pd 001 and 002 set 0) the spindle at 400hz (24,000rpm) seems to be the same max speed as what the computer is taking it to though even though Mach3 says that rpm is only 14,000rpm.... I’m very confused....
Any suggestions?
The absolute best thing to do is zero everything out completely and start all over again. It is 100 times more difficult to chase down a problem than to just reprogram it. However, Mach3 and your spindle will not always read the most accurate numbers you are expecting. It will be close but possibly a 1000 or so off. There is another part (the exact name of it I can’t recall right now) that would read the speed of the actual spindle very accurately and send that number to Mach3. With this kit it isn’t part of the package. It’s going to drive me nuts now till I can remember what it’s called. Either way if you clear out all of your settings and start again you should get it on track and running very efficiently.
@@702marine awesome! Thank you for that advise. I actually figured it out somehow fiddling around but ended up messing something up again after... I’m calling it a night for now as I’m getting frustrated. I’ll start over from scratch in the morning and message again if I have any questions. Thank you for your time!
Also let me know if you remember the name of that kit 😁
@@CharlieSolis did you figure it out? Mine is now doing the same thing yours was doing. It seems not to go up to 24000 rpm.
@@supremesupreme4289 hey I haven’t tried it yet. Got caught up with some other stuff. I will be trying soon.
I purchased the UltimateBee this spring 1500x1500 2.2K 220v air spindle xPRO controller. I had so many issues with the controller and getting the motors to move right I scrapped it and got a NightHawk controller. All the motors are working perfectly now, but I can not control the VFD. I have gone over all the settings and matched them up to what seemed to be the best choice and moved the jumper. Still, the spindle will not turn. I am hoping someone out there will be able to help me.
Why didn't you show digits on the VFD while using mach3 spindle speed jogging?
Great video!! I need some advice on a spindle. I’m trying to save a few bucks and avoid spending $1700 on an Avid 3hp spindle setup. I have on order a pro 4848 CNC from avid and I have been searching for an alternative to avoid using a regular router. What spindle and VFD could I purchase that can be controlled by Mach4? Any help would be greatly appreciated!!
Huanyang setup just like this would do you? Just makesure your controll board has a simmilar output. Its all mostly interchangeable anyway.
hello! I have the same complete set of the machine, please tell me where you can get the settings of the power supply for the spindle?
This is the link for the programming sheet:
stuckeyworx.com/Spindle-Inverter-info
@@702marine thank you very much!!
Thank you brother for great video i follow the steps 5 time and i rest my vfd every time but my problem when i click the spindle button the spindle is work but i cant change the speed and the spindle not power off when i press the button again
I have the same controller in the video
And the same vfd and spindle but 220 v
Water cooled
Can you help me
My vfd on program pd011 it won’t go higher than 50 any idea why?
you never talked about wiring the actual motor to the vfd, are you running 110 or 220, if 110 what 2 terminals are you using from the R S T? Also you you know the pinouts for the spindle from the U V W thanks
You should look at my other videos. If you believe you have still missed something reach out at that time. It’s also mentioned at least twice in this video that I am running a 110v system. Please do your homework before leaving accusatory comments... Thank you...
ua-cam.com/video/MAWpidbxifA/v-deo.html
@@702marine was not being accusatory. Was just asking question. I was trying to see the wire hookups but were not clear in the video so I thought I would ask
Making these videos take a lot of time and effort to do and to edit. I have detailed the complete assembly of this machine and have offered all of the information through my videos. Let me know if you need help with something I might not have covered in one of those videos...
My spindle doesn't move if I use M4 command. Any idea?
why is it showing spindle speed 3000 in mach3?
After a year of troubleshooting my UC300 Digital Dream I was finally able to get my VFD spindle to work properly. If anyone has this controller you must set the PWM setting control to1 and not 0. If you set it to 0 the spindle will maintain one speed only.
Could you explain where can i find the PWM setting control, is this some setting in Mah3 or is this plugin interface for the UC300 controler?
HI I HAVE DO ALL THE SETTING S LIKE YOU . BUT WHEN I RUN THE SPINDLE IN MACH3 ITS RUN AT THE LOW SPEED IF I ADD SPEED NOTHING STILL IN LOW SPEED PLEASE HELP
Hello,
I have a Huanyang vfd and 2.2kw spindle 220 volts. I did not reset my vfd when I put in the settings from several videos. It worked except it would only go to 208 hertz. I reset it and now it goes to 400 hertz but the potentiometer does not work. Is there a setting I can change to fix it. TIA
My spindle is GDZ-80-1.5 80X1.88
110V 1.5KW 5A
400HZ 24000RPM
Is it the same settings?
I have a workbee 1500x 1500 water cooled
I'm sorry for the late reply but yes 1.5 kw and the 2.2 kw are the same here. So long as they are the same volt.
i have a huanyang HYo2D211B inverter and a Huanyang GDZ 80. 1.5 ..110 volt spindle that will not run by this programming can you help please
Look me up on Facebook. It’s much easier to communicate and share images through that method. facebook.com/StuckeyWorx
I am running the Sainsmart 5100 my diagram for a vfd only shows 3 wires on my breakout board one on the ground, V1 on acm, and the for on fwd , would i hook up the wires to the vfw on the same locations as your setup I am using Mach3
Yes I would think so as there is the two into one connection on my setup where yours is just the one. The power is low on those wires so you should be safe testing around if needed.
@@702marine thank you
I don't have the whole kit you have but I do have the very same spindle and vfd. So I used this to program but my question is how can I make it run with the dile as the rpm change?
It actually just runs up real fast so I hit stop. Can't control it
BTW I'm not wanting to use mach3 to control it at this time
You are not using Mach 3? Do you want to control it just from the inverter?
Set PD002 to one and that’s it
Do these machines have to run on 110 can I run 240 as it is in England
Yes they have 220/240...
Hello Sir...
I'm using Mach3 USB Interface Board how I wiring it to Huanyang VFD? As I can not find out GND, VSO and OUT on the Interface. Can you help me?
hello
can I connect the same VFD with Spindle motor for GRBL NOT FOR mach3 ? !
If you are using a GRBL control unit you can. But if you are using a Mach3 controller you have to use Mach3 software to do the cuts.
I made all inverter settings and wiring like from your video, twice checked settings from Match3, but only work on/off spindle button. Whats wrong I made? S-ov and spindle speed is displayed as 0
Same here
Здравствуйте , вы решили проблемму ?
Why can I only get my spindle to go up to 391 Hz using an Mach3 an Gecko if you could help it would be appreciated can’t get all the way up to 400 I’m getting 10 V to the VFD but it is not going all the way up to 2400 RPMs Staying at 23 and some change if you could help let me know thank you
What you see on the Mach3 side will be a bit off from what the spindles actually doing. There is another part altogether you would need to have truly accurate readings of what the spindle is actually doing. The reading on the screen in Mach3 will be off +\- 1000rpm or so.
@@702marine I understand that the dilemma that I’m having is the VFD won’t go all the way up to 400 Hz it only goes to 391
PD072 is according to the manual the Lower Analog Frequency, this should be 133.33
PD073 is according tot he manual the Higher Analog Frequency, this should be 400
Correct? Because in the video (and your PDF) these settings are reversed, you say PD072 for Higher and PD073 for Lower?
EDIT: I think the values are correct as in the video and in the PDF, only the names are not?
The way I have it is the correct way. You must set the higher then go back and set the lower after. 73 to 400 first then go back to 72 and set it to 133.33.
Thanks!!
@@702marine it was 72 to 400 then 73 to 133.33 in your video
1 have 110V 1.5 kw 400hz spindle same VFR sounds like it's running 24,000 rpm but display says 11,500 am I doing something wrong
You might want to fix blukman so ppl find it.
ឣរគុណបង