Installing Livescope

Поділитися
Вставка
  • Опубліковано 18 гру 2023
  • After a long time debating whether or not to install Livescope on my boat, I went ahead and installed it. It was not the easiest install and at times very frustrating but it’s done and I feel good about it and excited to get out on the water and learn the system.
    #livescope #trackerboats #trackerpro170 #garmin #boat #diy #fish #fishing #BassFishing #LargemouthBass #crappiefishing
    Products in this video:
    www.basspro.com/shop/en/garmi...
    www.basspro.com/shop/en/garmi...
    www.scheels.com/p/amped-outdo...
    www.scheels.com/p/amped-outdo...
    www.amazon.com/dp/B01ABOPO2S?...
    www.amazon.com/dp/B07FW3GTXB?...
    www.amazon.com/dp/B08XWQHMZJ?...
    www.walmart.com/ip/Scosche-PS...

КОМЕНТАРІ • 15

  • @oldtrooper4686
    @oldtrooper4686 5 місяців тому +1

    Getting ready to install and looking for ideas. Love the battery box. That's what I call thinking outside the box.

    • @RFishingtx
      @RFishingtx  5 місяців тому

      Hahaha! Thanks! Good luck on the install.

  • @RF_Reggae
    @RF_Reggae 5 місяців тому +1

    Thanks for sharing some great ideas.

    • @RFishingtx
      @RFishingtx  5 місяців тому

      You are very welcome!

  • @timnationx7482
    @timnationx7482 2 місяці тому +1

    What did you use on the motor area to keep the cable centered? Is it glued or screwed? Great idea best I've seen on YT.

    • @RFishingtx
      @RFishingtx  2 місяці тому +1

      @timnationx7482 I used a U shaped bracket made of hard plastic and ran a bolt through. I wrapped the bolt with electrical tape to protect the sleeve that’s over the transducer cable and glued the bracket in place. This has worked out incredibly well.

    • @timnationx7482
      @timnationx7482 Місяць тому

      Any issues using spot lock and this rigging?

    • @RFishingtx
      @RFishingtx  Місяць тому

      @@timnationx7482 So far no issues

  • @charlesbarnwell6237
    @charlesbarnwell6237 5 місяців тому +1

    How did you get the cables out of the storage compartment with out the wires being exposed on the deck?

    • @RFishingtx
      @RFishingtx  5 місяців тому

      @charlesbarnwell6237
      I ran a flexible rod from the storage compartment to the bow which allowed me to tape the cables to the rod and then pull them through under the deck into the storage compartment. I hope that answers your question. Let me know if you have any more questions. I’m always happy to help.

  • @janicerice1632
    @janicerice1632 4 місяці тому +1

    How did you get the end connector for the transducer cable through the 1/2” braided cable sleeve?

    • @RFishingtx
      @RFishingtx  4 місяці тому +1

      @janicerice1632 The cable sleeve has a slit in it. When the sleeve is opened up and the cable is run inside, the sleeve then rolls tightly up on itself. This allowed me to put the sleeve on after the cables were run from the bow to the storage compartment. Hope this answered your question.

  • @Hunterpenuts
    @Hunterpenuts 5 місяців тому +1

    How long does that battery run it any issues

    • @RFishingtx
      @RFishingtx  5 місяців тому +1

      @Hunterpenuts No issues as of yet and I’m getting a full day out on the water with it right now.

    • @charlesbarnwell6237
      @charlesbarnwell6237 5 місяців тому

      HOW did get the cables ran from
      from inside the box?