So, all of that snakey looking design work from the outside was literally just aesthetics, and nothing at all to do with functionality. That's disappointing.
интересно на каких чайников рассчитаны такие видосы ? И больше всего прикалывает что без разницы что они восстанавливают , бензопилу или нинтендо ,в начале обязательно измажут снаружи в грязи ,ритуал у них такой что ли ?
I have been looking for this Kenwood subwoofer over the years because of the unique shape and it was manufactured in 1994-95. This is made in Singapore Kenwood clear shinny black finished. Didn't know there is a made in Malaysia that is gray or charcoaled finished. The made of Japan electronics on those times are quite expensive and well built. On those times, this is an expensive accessories for my Kenwood mini-component. Those are the last era where the components are in one box not the modular in the 70's and early 80's. So I didn't buy the subwoofer because I am contented of the 3 way speakers. Anyways, I have the privilege to see how this was restored. If the shipment is not expensive. I will buy this one now. Thank you so much !!!. I appreciate what you do.
Hello! ♥Sorry to say, but I think you attach the speaker to amplifier wrongway. You must change "plus" and "minus", then air will flows otherwise: from inside to out. And sound will be better!
Speaker was wired properly. The spade terminals are different size, and he didn't modify the wiring so impossible to wire backwards. What happened was the phase was set to reverse.
this was considered a very good budget subwoofer back in the day, it didn't produce a lot of output but due to it's design, had a very good low frequency response and looked pretty cool and output good base in almost any part of the room. I have never seen an SW-05 but I have seen an SW-500 which is the replacement for this in the mid to late 90s which was very similar in desgn.
Reminds me of my first subwoofer, it was a 12" isobaric with paper cones. I didn't have much of an amp to power it but man that thing sounded so good with just an 80W input.
Nice restoration! I had one of these back in the 90s. Decent little sub which looked great (always commented on for the aesthetic!). Unfortunately it eventually died after about 25 years of service. RIP, Kenwood subwoofer.
Смените полярность подключения динамика, это видно по пакетику, который засасывает в сабвуфер. У любого низкочастотного динамика ход диффузора наружу больше, чем внутрь. Именно из-за неправильной полярности питания динамика у вас стучит звуковая катушка, и идет искажение звука
@@borincod при прямой полярности (плюс к плюсу, и минус к минусу) диффузор ходит наружу. При обратной внутрь, из-за этого на большой громкости может начать стучать катушка об торец сердечника магнитной системы. Если динамик не нагружать, то стучать не будет. В некоторых компановках короба сабвуфера допускается обратная полярность, но точно не для четверть волнового.
@@borincod именно поэтому и пакетик втягивает внутрь порта сабвуфера. При прямой полярности он должен колебаться на входе в порт, и если его отпустить, он должен зависнуть, либо его вытолкнет наружу.
@@ИзделияИзКожи всё-таки ваш ответ неясен... Если бы сабвуфер постоянно засасывал воздух, а вместе с ним и пакетики, то он бы неминуемо лопнул через некоторое время. Если же сабвуфер будет постоянно воздух выдувать, то в какой-то момент воздуха внутри коробки не останется вовсе... там был бы ваакуум. Согласны?
@@borincod не согласен. Во-первых он не засасывает постоянно, ведь динамик совершает колебательные движения(возвратно-поступательные). Просто при положительном значении синус-сигнала динамик работает в одну сторону больше, чем в обратную, поэтому при обратной полярности диффузор больше ходит внутрь корзины, и из-за этого и создаётся эффект засасывания пакетика в порт сабвуфера. Простыми словами пакетик будет зависать как и при прямой полярности, но глубже в порте, а т.к. его держат вне порта, то он стремится в него попасть. При прямой полярности этот пакетик, если его отпустить будет зависать и колебаться прям на входе в порт
Strange to see their is actually rust on plastic parts. I didn't know tplastic could rust. And although the unit looks battered and well used and appears to have been subjected to various weather influences the delicate silk-screen lettering on the unit is soehow in pristine condition. This is not a restoration, this has all the hall-markings of a working product that was in decent nick, that has been deliberatlly been made to look battered en bruised so it could be 'restored'.
Well the the wood inside was subjected to water and dissolved that's a fact you see it in the video! and rust can came from rusting metal parts at the scrapyard, but who cares :)
Great restore, but the speaker seems to be sucking in air which is reverse. If air is not coming out then sound is not coming out, the polarity of the speaker is wrong. This is still a good box restore.
... Wrong. The air vibrates. There's no sucking or blowing. Reversing polarity doesn't change that. Also this is one of the dumbest marketing tricks for an otherwise poorly performing sub.
Yes, he did sort of fly through on checking the components. I thought he is an electronics whiz or he’s confused. Maybe just putting on a show. You always take your time and make sure the components are disconnected. There can be false readings when you check them still attached to the circuit board.
I bought the Dayton SUB-1200 12" 120W it's already plenty to get the cops called. My living room isn't very big so it doesn't take a lot to really get things rumbling. Alongside a Polk Monitor II based surround setup it's a very natural fit to the space. My Onkyo receiver isn't the cheapest model but it's pretty modest and the sub helped a lot with running the power hungry Polks. I used to run a separate amp for my front pair but no longer need to. My home theater isn't my main Hi-Fi setup and bangs hard enough from the receiver. The Dayton is a really great value just because it's cheap and doesn't suck. More serious subs are better but it gives you most of the experience for not a lot of money.
@@Mikhail_malar I bought it to fill a space and fill out the sound in my home theater. I also bought it to remove work from my front speakers and receiver which makes them sound much better. I didn't need it to be exceptionally powerful just large enough to move air which it is, and powerful enough to not clip which it is. I can turn it up loud enough to shake the house and generally run it set very low in power. My home theater sounds great and the bass is plenty loud enough. Moves and music sound excellent.
@@geeknproud321 let's talk garlic, it's old, it's better to take a new Sub and not know the problems, the quality is higher, the size is smaller, the bass is more
i am from the philippines,and i admire what you are doing when it comes to restoration,i watch all of your work,i am so proud of your works when it comes to restoration,so go on idol,thanks for your videos,its really worth....thanks idol...
Unfortunatelly this video is fake. This guy are clearly taking a good subwoofer, "dirting" them realistically, and after this, came the incredibly skills of the restorator... Look ah the quality of components inside... All of them are completely CLEAN. and from the outside this looks like the subwoofer was buried underground... If this are really buried even for a week only, a lot of electronic components will inevitably fail and corrode... ONE DAY BURIED MAKE A HUGE WASTE ON ELECTRONICS...
Esse video é falso man... Esse é mais um daqueles canais que sujam de forma realista aparelhos eletrônicos pra fazer esses videos de restauração... Existem muitos canais assim. Só você analisar o seguinte: estava coberto de sujeira, terra pra todo lado, com marcas até de que tinha molhado e secado, E NÃO TINHA UM ENFERRUJADO POR DENTRO. ou esse cara é o mano mais sortudo do mundo, ou o video é fake.
That is amazing to see I had one of these when they first came out. In my front room I had two large windows and when I turned this on it used to make the windows actually bend and shake. Back in the day this had quite a powerful punch. It was part of my first surround sound system
That's a fake video... For a really dirty exterior, was incredibly clean inside... Just with a little dirty dust... No corrosion, no oxidation... VERY CURIOUS
Só é uma pena que o video é falso. Eu acompanho muitos videos de restauração porque faço algumas por hobby. E bem, pra um aparelho completamente sujo por fora do jeito que estava, É IMPOSSÍVEL não ter corroído nads por dentro, nem ter ferrugem nas partes de metal... O que essa galera faz é pegar aparelhos bons, sujar eles "de forma realista" pra depois fazer o video desmontando e limpando como se eles tivessem tido a sorte de pegar um aparelho ainda bom...
Fun to watch!, but unless this is for some form of family keep sake "for the memories" I can't personally see putting that much into fixing a maybe $50 when it was new sub.
@@Alex_N_Nov ну в видео прикручивал динамик он правильной стороной. а то что саб засасывает воздух - физику не знаю, но на некоторых видосах видел как саб засасывает что-то рядом лежащее
So, all of that snakey looking design work from the outside was literally just aesthetics, and nothing at all to do with functionality. That's disappointing.
That's Kenwood...
Felt the same, was hoping it was dome sort of folded horn, nope lol.
Was thinking the same thing, I had to rewind it when he put it back together cause I thought I missed something.. Lol
just by the size, if it was a folded horn it wouldn't have any deep bass at all as the horn length is very important
It looks to be a 4th order bandpass so id expect some atleast mediocre sound.
Молодец разные элементы проверил не переключая режимы мултиметра!!!!! Красавчик!
интересно на каких чайников рассчитаны такие видосы ? И больше всего прикалывает что без разницы что они восстанавливают , бензопилу или нинтендо ,в начале обязательно измажут снаружи в грязи ,ритуал у них такой что ли ?
@@OpaRus71 Они сначала снимают хороший прибор, а потом портят, потом мантируют так, как будто, востоновили.
@@OpaRus71 yep, totally real. He just dug the subwoofer off out of the mud! 😂
kenwood ตัวนี้อยากได้มาก นึกว่าสูตรตู้จะเป็นเขาวงกตเหมือนทรงข้างนอก ที่จริงโดนหลอกมาตลอด ขอบคุณ Thank you. ที่เฉลยให้ดูครับ
When you see open toe sandals and 1982 soldering irons , it’s a legit workshop !!
I have been looking for this Kenwood subwoofer over the years because of the unique shape and it was manufactured in 1994-95. This is made in Singapore Kenwood clear shinny black finished. Didn't know there is a made in Malaysia that is gray or charcoaled finished. The made of Japan electronics on those times are quite expensive and well built. On those times, this is an expensive accessories for my Kenwood mini-component. Those are the last era where the components are in one box not the modular in the 70's and early 80's. So I didn't buy the subwoofer because I am contented of the 3 way speakers. Anyways, I have the privilege to see how this was restored. If the shipment is not expensive. I will buy this one now. Thank you so much !!!. I appreciate what you do.
What is the model name ??
@@dominikdenci204 Modelo SW-05, tenho 1 aqui no Brasil. Otimo SUB
Hello! ♥Sorry to say, but I think you attach the speaker to amplifier wrongway. You must change "plus" and "minus", then air will flows otherwise: from inside to out. And sound will be better!
odevolv tumb a nd 3, seis ndev
Speaker was wired properly. The spade terminals are different size, and he didn't modify the wiring so impossible to wire backwards. What happened was the phase was set to reverse.
Bro, entire video was fake. The subwoofer just got an really dirty layer to feel old and trash... But originally the subwoofer was okay...
Hadir menyimak sampe selesai bosku
Thanks for speeding it up. Very enjoyable.
this was considered a very good budget subwoofer back in the day, it didn't produce a lot of output but due to it's design, had a very good low frequency response and looked pretty cool and output good base in almost any part of the room. I have never seen an SW-05 but I have seen an SW-500 which is the replacement for this in the mid to late 90s which was very similar in desgn.
¹qc
Reminds me of my first subwoofer, it was a 12" isobaric with paper cones. I didn't have much of an amp to power it but man that thing sounded so good with just an 80W input.
it's shitty for highs?
you know, I would bet you that all this needs is to be mounted to a properly-sized floating surface used as as resonator
Bass not base.
The legendary subwoofer for completed the cd's stereo set in 90s.
bro is that one of those foreign youtube trend sweat shops thats crazy.
Nice restoration! I had one of these back in the 90s. Decent little sub which looked great (always commented on for the aesthetic!). Unfortunately it eventually died after about 25 years of service. RIP, Kenwood subwoofer.
Dakotah, you have been selected for the giveaway session, don't ignore this.
@@Hero10838 ?
Resurrect it!
Смените полярность подключения динамика, это видно по пакетику, который засасывает в сабвуфер. У любого низкочастотного динамика ход диффузора наружу больше, чем внутрь. Именно из-за неправильной полярности питания динамика у вас стучит звуковая катушка, и идет искажение звука
каким конкретно образом поляроность подключения динамика влияет на пакетик?
@@borincod при прямой полярности (плюс к плюсу, и минус к минусу) диффузор ходит наружу. При обратной внутрь, из-за этого на большой громкости может начать стучать катушка об торец сердечника магнитной системы. Если динамик не нагружать, то стучать не будет. В некоторых компановках короба сабвуфера допускается обратная полярность, но точно не для четверть волнового.
@@borincod именно поэтому и пакетик втягивает внутрь порта сабвуфера. При прямой полярности он должен колебаться на входе в порт, и если его отпустить, он должен зависнуть, либо его вытолкнет наружу.
@@ИзделияИзКожи всё-таки ваш ответ неясен... Если бы сабвуфер постоянно засасывал воздух, а вместе с ним и пакетики, то он бы неминуемо лопнул через некоторое время. Если же сабвуфер будет постоянно воздух выдувать, то в какой-то момент воздуха внутри коробки не останется вовсе... там был бы ваакуум. Согласны?
@@borincod не согласен. Во-первых он не засасывает постоянно, ведь динамик совершает колебательные движения(возвратно-поступательные). Просто при положительном значении синус-сигнала динамик работает в одну сторону больше, чем в обратную, поэтому при обратной полярности диффузор больше ходит внутрь корзины, и из-за этого и создаётся эффект засасывания пакетика в порт сабвуфера. Простыми словами пакетик будет зависать как и при прямой полярности, но глубже в порте, а т.к. его держат вне порта, то он стремится в него попасть. При прямой полярности этот пакетик, если его отпустить будет зависать и колебаться прям на входе в порт
Galing ah bulok na napakinabangan pa galing na ata sa basurahan yan lods
Outstanding 👍🏻👍🏻
Strange to see their is actually rust on plastic parts. I didn't know tplastic could rust. And although the unit looks battered and well used and appears to have been subjected to various weather influences the delicate silk-screen lettering on the unit is soehow in pristine condition. This is not a restoration, this has all the hall-markings of a working product that was in decent nick, that has been deliberatlly been made to look battered en bruised so it could be 'restored'.
of course that's what's going on here. fake.
Wood shavings
Well the the wood inside was subjected to water and dissolved that's a fact you see it in the video! and rust can came from rusting metal parts at the scrapyard, but who cares :)
but this one from MR Electricity do You think its fake to:) ua-cam.com/video/rFKoqjUI_0U/v-deo.html
Thank you. I was wondering why this was titled "restoration" 😂
That thing looks like a cannon. Nice job
HOLY CRAP! I've got one of These 'Out In the Backyard Shed'!
It wasn't Exactly Accurate, BUT OMG! the Windows Vibrated when I TURNED IT TO ELEVEN 🤣
Hi..I want my JVC 5.1 home theater repaired...almost 15 years old...can any one in India repair it with Genuine parts??
pakar betul. bagus👍
Very very god 👍
Nice job, but. Watching you cut the hole in the mdf was BRUTAL.. the way you use a drill really urked me for some reason lol. But yeah good job
He's also using a drill for screws,.. should be a 1/4" impact instead.
Great restore, but the speaker seems to be sucking in air which is reverse. If air is not coming out then sound is not coming out, the polarity of the speaker is wrong. This is still a good box restore.
Yeah it's supposed to blow air out
@trucker 9000 he means it's connected wrongly
Either way, it’s a subwoofer. What I heard was was a sub whisper!! Like the commercial of the day, “Wheres the BASS?”
... Wrong. The air vibrates. There's no sucking or blowing. Reversing polarity doesn't change that. Also this is one of the dumbest marketing tricks for an otherwise poorly performing sub.
Are you serious?.... No, you are wrong.
ну пипец кенвуд ----------- круто -- но плёнку всасывает круто ------------------ класс аппаратуру выпускали раньше и всем было отлично супер акустика
Ничего что он тыкает щупами куда попало? Никого это не смутило? 😂
Боец в электронике полный ноль!
@@albo963 Главное сделать вид 😆
Yes, he did sort of fly through on checking the components. I thought he is an electronics whiz or he’s confused. Maybe just putting on a show. You always take your time and make sure the components are disconnected. There can be false readings when you check them still attached to the circuit board.
Amazing job
Creatively designed miniature cannon! I think the bass response is somewhere in the 40Hz region.
Hola tengo uno igual de forma intacta como nuevo en casa y lo cuido mucho .. saludos
I bought the Dayton SUB-1200 12" 120W it's already plenty to get the cops called. My living room isn't very big so it doesn't take a lot to really get things rumbling. Alongside a Polk Monitor II based surround setup it's a very natural fit to the space. My Onkyo receiver isn't the cheapest model but it's pretty modest and the sub helped a lot with running the power hungry Polks. I used to run a separate amp for my front pair but no longer need to. My home theater isn't my main Hi-Fi setup and bangs hard enough from the receiver. The Dayton is a really great value just because it's cheap and doesn't suck. More serious subs are better but it gives you most of the experience for not a lot of money.
120w... 120? .... 120 ! 😴
@@Mikhail_malar I bought it to fill a space and fill out the sound in my home theater. I also bought it to remove work from my front speakers and receiver which makes them sound much better. I didn't need it to be exceptionally powerful just large enough to move air which it is, and powerful enough to not clip which it is. I can turn it up loud enough to shake the house and generally run it set very low in power. My home theater sounds great and the bass is plenty loud enough. Moves and music sound excellent.
@@geeknproud321 let's talk garlic, it's old, it's better to take a new Sub and not know the problems, the quality is higher, the size is smaller, the bass is more
This is soothing and satisfying to watch thankyou! 😊
Speaker : no test
Electronic : no test
😆😆😆😆😆
Where do you get these things, from ponds or rivers? It always looks like these things were dug out of the ground..... 😆
🤣
i am from the philippines,and i admire what you are doing when it comes to restoration,i watch all of your work,i am so proud of your works when it comes to restoration,so go on idol,thanks for your videos,its really worth....thanks idol...
bro, its fake
Unfortunatelly this video is fake. This guy are clearly taking a good subwoofer, "dirting" them realistically, and after this, came the incredibly skills of the restorator...
Look ah the quality of components inside... All of them are completely CLEAN. and from the outside this looks like the subwoofer was buried underground...
If this are really buried even for a week only, a lot of electronic components will inevitably fail and corrode... ONE DAY BURIED MAKE A HUGE WASTE ON ELECTRONICS...
Like how all these guys coat thing with mud, then clean it off and we all go wow! 🤭
I hate this kind of videos so much... And i hate more because a lot of people really thinks this are a legitimate video...
Hmmm! How old is this? Pretty cool seeing a quasi 6th from back then!
Parabéns 👏🏻👏🏻👏🏻 , ótimo vídeo , obrigado ‼️🔊✌🏻
Tenho um subwoofer desse guardado há anos , tenho que consertá-lo 😕
Esse video é falso man... Esse é mais um daqueles canais que sujam de forma realista aparelhos eletrônicos pra fazer esses videos de restauração... Existem muitos canais assim. Só você analisar o seguinte: estava coberto de sujeira, terra pra todo lado, com marcas até de que tinha molhado e secado, E NÃO TINHA UM ENFERRUJADO POR DENTRO. ou esse cara é o mano mais sortudo do mundo, ou o video é fake.
Cool video…just wondering if the speaker was out of phase..seemed to be sucking a lot of air in rather than pushing it out through the bass port?
😝😂😂😂
Always wanted one of these when I was young 90s eat your heart out... classic man.......
Saludos de Mexico amigos
Great jop Congratulations you tbe best
That is amazing to see I had one of these when they first came out. In my front room I had two large windows and when I turned this on it used to make the windows actually bend and shake.
Back in the day this had quite a powerful punch. It was part of my first surround sound system
Там динамик меньше ладошки ребенка, какие стекла этот "сабвуфер" тебе гнул ?)
👍👍👍👍
Sounds like the party upstairs.
I was expecting the thing to blow out my earbuds. like you said, we got the sound system cranked up inside the house instead!!
your circular saw table , this home made ? do yo have a video this fabrication ?
WOW. ! you did a very great job, so proud of your work. great video
That's a fake video... For a really dirty exterior, was incredibly clean inside... Just with a little dirty dust... No corrosion, no oxidation... VERY CURIOUS
Excellent video!
Awesome relaxing video. The only thing I have negative to say is the sounds from your camera
👍Nice Job.
OK!!!!!!very very good ok restauration!!!!🆗💯💢💯👍🤗
Có vỏ thùng loa full bán ko bác? Thanks you!
Полярность динамика перепутал....пленку должно выталкивать из трубы ,а не засасывать.....🤔🤔🤔
Good job 👍👍👍Thank you for sharing. Be safe 🇨🇦
... on the bench saw
I don't know what camera you are using, but if you can I would suggest getting a lens with a quieter auto focus or an external mic.
did you eat the giant capacitors for essential electrolytes?
Amazing.. 🥰🥰🥰🥰🥰
Wow idol ok yan
Show parabéns sucesso sempre
Bác ở chỗ nào hải dương đấy. Ở kim xuyên hả
I have still got one of these. Bloody good sub
The later one though. Got it connected to a kenwood system from the same era
old kenwood subs was sick in design, remind me Ariel, small siren from disney movies xd
ligou o falante invertido os pólos?
Great work!👍👍
I agree
bro, it's fake
Good Video 👍👍👍
Nossa 😱que liiiindooo 😍🥰
Só é uma pena que o video é falso. Eu acompanho muitos videos de restauração porque faço algumas por hobby. E bem, pra um aparelho completamente sujo por fora do jeito que estava, É IMPOSSÍVEL não ter corroído nads por dentro, nem ter ferrugem nas partes de metal... O que essa galera faz é pegar aparelhos bons, sujar eles "de forma realista" pra depois fazer o video desmontando e limpando como se eles tivessem tido a sorte de pegar um aparelho ainda bom...
In the end it came back home to China where it was supposedly fixed under warranty?? Lmao 🤣😂🤣
cool vid.
why is the speaker sucking instead of blowing?
Nice watching from Philippines
bạn ở đâu hải dương vậy
with love from India. good work .
mình kết nhất cái volum tổng ý,, kiếm mãi ko ra lun
Did you smear shiizt on it before you started for the LOLZ or did you really get it that way?
wow, very nice
Que paso con las pistas cortadas en el control de volumen no veo que las haya hecho puente ...??? Ó trabaja por inducción....🤔🤔🤔
whats the buzzing noise in few first second of video??? its your camera??a
Pick up a random electronic device + cover with mud = profit with UA-cam!
Love from Sierra Leone 🇸🇱
Very nice !, it can be more nice if you show how Decible frekwency . May be use frekwency meters.
That horn ain't just folded- its folded, flipped, smothered & covered! 🧇
In the beginning of the video, is that the new Kenwood sound dampening mud?
Пздц, гвозди и пва. Просто гениальная реставрация
The curious case of a subwoofer covered in dirty, BUT THE ELECTRONICS INSIDE ARE NOT CORRODED. what a lucky guy!
Fun to watch!, but unless this is for some form of family keep sake "for the memories" I can't personally see putting that much into fixing a maybe $50 when it was new sub.
Se tivesse pego a umidade que mostrou no vídeo, esse compensado tinha estourado todo. vídeo caô kkkkkk...
Динамик саба не с фазирован. А так всё супер.
с чем не сфазирован? он там один
@@mygreatlord по идее он в обратную сторону должен дуть
@@Alex_N_Nov тоесть внутрь коробки? ну разве что по какой-то извращенной идее
@@mygreatlord так он у него как раз и внутрь коробки дует судя по тому как плёнку засасывает
@@Alex_N_Nov ну в видео прикручивал динамик он правильной стороной. а то что саб засасывает воздух - физику не знаю, но на некоторых видосах видел как саб засасывает что-то рядом лежащее
At 10.45 min, which solution you have used by brush?
2 pontos: 1 vc esqueceu 1 parafuso da placa de controle do volume e 2 a ligação dos fios do alto falante estão invertidos. Fora isso ficou muito bom.
Looks like a subwoofer HR Giger would create.
Check out the B&W Nautilus (original, not the 800/etc) if you want the ultimate Giger speaker.
Restoration is actually better than how it was built from Kenwood.
Buena restauración, ése sistema de subwofer no lo conocía, dedo arriba.
Those two mosfets had a HUGE cooling block
Ok three mosfets
Is it out of phase?
В какой грязи вы его покачали чтобы восстановить сей аппарат?
i bet h.r giga loved the desighn of this sub woofer
Kindly ans will you repair my home theatre
Kenwood? That's wrapping a dog turd in gold! 😂
😂😆 I thought that was a old pirate cannon
Should have played some music so we could hear it WORK
When I saw the picture, I thought that might be interesting. And then in the video I saw this little thing. I hoped it would be at least 1m long...
Was it left on a beach?
Kenwood ❤❤❤❤
Wow♥️