The Honda service manual for this model and the Honda common service manual are both available online, between them you can see how to sync the carbs...
Just in case anyone else needs the info: If the carb tuner is jumping around on the readings then you need to flip the hoses around and put the connectors at a different distance between the tuner and engine. This smooths out the air pull. I think they mention this in the instructions.
Where did you get that blanking screw Deano? There was a little brass nipple on mine leaking loads of air in, the rubber cap is silly money from Germany! What size is that bolt?
Thanks for the video Deano , why oh why did they make it so hard to balance the carbs when they built the bike ??. How did you cap the hoses when you left them on the bike ?. I’m kicking myself because I have just had the carbs off for new jets and could of done the hoses then !!😭.
Screwed in 6mm ( I think, perhaps 4 mm) machine threaded bolts/ screws, then taped over ends just to be sure. You can use anything that plugs the tube, and will not fall out, or get drawn into the tubes.
Those carb clamps are meant to be flipped the other way it’s not meant to be anywhere near as hard as you’ve had. Someone’s been in before and made the job 10x harder for them
Well spotted, I never had the privilege of knowing at the time, and as you say it was a NIGHTMARE for me 1st time trying. Its a good tip on your part too, so no one else makes the error of putting back the wrong way.
honestly I felt this was almost a useless video. you showed no balancing. no showing it running smoother afterwards. nothing to where you hooked the balancing tool to.
I know, if I had the bike, I would have continued the vid, it was done way back when I only just started doing, and as you saw, ran out of time and light. Trust me I have thought the same. However u like yourself many have still found this of use and value, and given me many likes and positive feedback. I put it on to help other where I could a long time ago, so take from it what you will..... What is your constructive criticism ?
Think you are missing the point mate.....I have now balanced the carbs on the YZF, the XJR and the VFR. Once you learn how to do one, the rest follow. Paying someone else, means you never learn, and you pay forevermore more.
I was when I first attempted it ! Kenneth is going to show us all how it can be done from start to finish in TEN minutes folks ! Thanks Kenneth, please let us all know when you have this video up, we hold our breath in anticipation.
Welcome to the club buddy took me 5 hours getting my carbs off my 94 F2' they have never been removed before.
Sounds about right, they suck the first time
The Honda service manual for this model and the Honda common service manual are both available online, between them you can see how to sync the carbs...
Did the balancing sort out the dead cylinder?
Just in case anyone else needs the info: If the carb tuner is jumping around on the readings then you need to flip the hoses around and put the connectors at a different distance between the tuner and engine. This smooths out the air pull. I think they mention this in the instructions.
Thanks Adam, I think back then was my first time using that system, was a bit rushed by the time it was night too. Far from ideal.
Where did you get that blanking screw Deano? There was a little brass nipple on mine leaking loads of air in, the rubber cap is silly money from Germany! What size is that bolt?
Thanks for the video Deano , why oh why did they make it so hard to balance the carbs when they built the bike ??.
How did you cap the hoses when you left them on the bike ?.
I’m kicking myself because I have just had the carbs off for new jets and could of done the hoses then !!😭.
Screwed in 6mm ( I think, perhaps 4 mm) machine threaded bolts/ screws, then taped over ends just to be sure. You can use anything that plugs the tube, and will not fall out, or get drawn into the tubes.
Hello how are you. A question. How did you get the RPM to remain stable? I hope you can help me because CBR f3 I can't remove these variations
I use the vac guages..and dont need to take the carbs off...
Those carb clamps are meant to be flipped the other way it’s not meant to be anywhere near as hard as you’ve had. Someone’s been in before and made the job 10x harder for them
Well spotted, I never had the privilege of knowing at the time, and as you say it was a NIGHTMARE for me 1st time trying. Its a good tip on your part too, so no one else makes the error of putting back the wrong way.
What a work! Well fone. Never give up.
Je veux un moteur 600 cbr f3 et savoir combien il coute
It's a nightmare. I feel the pain. Anyone find any information to bypass the air solenoid?
Make tall screwdriver really tall for that job. Welcome to jamaica
honestly I felt this was almost a useless video. you showed no balancing. no showing it running smoother afterwards. nothing to where you hooked the balancing tool to.
I know, if I had the bike, I would have continued the vid, it was done way back when I only just started doing, and as you saw, ran out of time and light. Trust me I have thought the same. However u like yourself many have still found this of use and value, and given me many likes and positive feedback. I put it on to help other where I could a long time ago, so take from it what you will.....
What is your constructive criticism ?
@@DeanAllen show where you hook up the tool to. Thats the main thing people beed
You dont need to remove the carbs off the bike....to balance the carbs...
Couldn't agree with you more, in fact, it is impossible to balance the carbs with a vacuum gauge if they are not on the bike, it has to be running.
😂🤣😂🤣😂 put the tools away and pay someone.
Think you are missing the point mate.....I have now balanced the carbs on the YZF, the XJR and the VFR. Once you learn how to do one, the rest follow.
Paying someone else, means you never learn, and you pay forevermore more.
Stuntcass UA-cam 👍 👍
I have a 80cm screw driver, can leave the mounting plates on
👍
Absolutely clueless, takes 10 mins to get them carbs off.
I was when I first attempted it !
Kenneth is going to show us all how it can be done from start to finish in TEN minutes folks !
Thanks Kenneth, please let us all know when you have this video up, we hold our breath in anticipation.
I’ll pay you to do mine in 10 minutes Kenneth 😉
Make video
Kenneth please make a video
@@DeanAllen kenneth uses an angle grinder.
Ни куя не понял.
What don't you understand, how can I help ?