PROGRAM KEYLESS ENTRY REMOTE for GM / Chevrolet / GMC 1998-2006 Review of New GM Factory Replacement
Вставка
- Опубліковано 13 лют 2017
- Buy Replacement Key-Fobs here: amzn.to/2Ehl16m
Program keyless entry remote for GM / Chevrolet / GMC 1998-2006 Review of New GM Factory Replacement Remotes - Авто та транспорт
Finally, a regular "Joe" explains it like a good friend. Thanks for your video. It worked well on my 2006 Saturn Vue. I did take the time to clean the muck out of the remote's innards and made sure the contacts were clean as well, and installed a new battery, as the old one showed up a tad weak on my battery tester.
Glad we could help. Thanks for watching.
Thank you so much for this!!! This is the kind of thing UA-cam is for. My remote died and I thought it was the truck receiver in the dash. Turns out…just an old remote. Thank Goodness!!! My truck is a 2000. I got 23 years and 230K out of this remote. I wish more stuff was built to last like this. Anyway, you really saved me. Thanks so much.
Thank you so much! The dealership wanted to charge me $75.00 to do this!
Glad it helped, Thanks for Watching.
Just ordered for my 2000 Buick Century. Will follow your instructions once I get it.
Glad to help
Thank you so much for making it so easy to program my remote. Much appreciated!!
Glad it helped
Any tips for a fob that stops working but shows no signs of damage or wear? I bought an official ACDelco replacement fob that stopped working after 3 weeks. Dealer programmed. Normal use, not dropped or stepped on, no water damage. Battery is good.
I could get a warranty replacement from ACDelco but really don't want to pay programming fee again. Amazon did give me a refund and didn't make me send it back. So if i could fix it that would be great! Otherwise i may get a Dorman fob that comes with programmer at AutoZone.
The best way to troubleshoot that is to buy a cheapo remote and see if it works. If it does, the remote is bad. If not, then you may have a problem with the receiver in the vehicle. That system is harder to diagnose and more expensive as well. Thanks for watching.
Excellent Video.. and this is a great help. Thanks for taking the time to make and post this!
Glad it helped, thanks for watching
My driver side door won't unlock and lock the second time after I turned my key on and off twice it just stayed in the lock position
I think you were very informative. Thanks! Hope your video helps when mines arrive.
Glad we could help. Thanks for watching.
TAKE YOUR REMOTE and open up the two halves. There will be a circuit board with a smooth side. The rubber buttons all have black dots on the black dots on the inside. Cut or punch out tiny little cirles of tinfoil. Use a small amount of superglue.to stick them to the dots. Should be all good. Snap back together and give it a try. Don't use too much glue or you wont gt a good connection. Hope this helps somebody. Ive had my Cobalt since new in 06. My remotes crapped out a couple years in. I went 5 years without them until I found this trick out. Fixed both my remotes. Twelve years later and still am using the same remotes.
Good Info. Thanks for watching.
Not really necessary. I've cleaned TV remotes for many decades. Clean the circuit board and button pads with 99% isopropyl alcohol. Do NOT use acetone or denatured alcohol!
I just bought a new transmitter 1 month ago and now my transmitter works flawlessly inside the car but doesn't want to work outside the car I'm not sure what to do...
Great video! Thanks for sharing. Will this method work for 2006 Chevy equinox ?
Not sure on that, give it a try. Can't Hurt. Thanks for watching
I enjoyed your video. It was very helpful. Thank you!
Glad it helped. Thanks for watching.
I have the same remotes but will that method of getting to program mode work on a 97 saturn sl2, the fob unsynced and now I have to resync it
Maybe, give it a shot. Nothing to lose.
I really enjoyed driver 1 and 2 via the key fob on my 2004 GMC sierra. This feature was embedded in the gage cluster. In 2005 the cluster changed and you lost a lot of feature available in the DIC. My 2006 Yukon has memory seats on the door panel, but I don't have the feature via the key fobs, even though the fobs still read 1 and 2.
I had no idea, all my 03's have it on the fob and the door panel. I have not checked the 05 yet.
Will this procedure work on my 1999 Corvette? I truly appreciate any help on this as trying to find someone to do this here in Las Vegas that will NOT rip me off is challenging. Many thanks
It might, give it a try, nothing to lose.
At least I was able to reprogram the old key fog to open the doors. Thanks.
Glad it helped. Thanks for watching.
This worked great! Thanks for posting it!
Glad we could help. Thanks for watching.
Thanks for the advice. It was the best. Good luck my friend
Glad we could help, Thanks for watching.
My remote only has lock and unlock. To make it beep do I need to buy a couple remotes, because I want it to beep when I lock it (Look for it in a parking lot when I have no idea where I parked)
The 'beep' is a setting in your vehicle, not part of the remote. Thanks for watching.
Good day sir and thank you for your video a quick question I have a 2000 Chevy Silverado pickup and I tried this with the locks but nothing happened I tried it twice and still nothing happen any advice thank you
Make sure you have the proper remote and a good battery in the remote. See an updated video with regards here: ua-cam.com/video/ntM72DJ5BC0/v-deo.html
The only down side is my driver set moves every time I hit the unlock button. Is there a way to get that to stop or is that in the programing ?
That option is in the menu on the dash. It can be turned off or on from the dash readout.
Why cant I program a 2002 Malibu key fob myself??? Mine says I have to have a locksmith or dealership do it, but what do they use that I dont have or cant get myself?
sare kay: Pop your trunk lid and pull the liner back behind passenger tail light and tell me if you see a small black two pin connector on the wiring harness. It should be wrapped around the antenna or brake light wiring. You have to get your head up in there to find it.
Edit: Sorry I didn't include the first time. Once you have located the connector perform the following steps: use a small piece of wire to jump (connect) the pins, you should hear the door locks cycle that means you are in program mode; make sure jumper stays in place (may need an assistant) then press and hold both the lock and unlock buttons on your remote until you hear the locks cycle then release; (you can program more than one if you have it), remove jumper and you're done.
Dammmnit.wow thanks brother, I freaked out when I just saw the remote but I saw your video and I got in the first try thanks a lot
Glad we could help, Thanks for watching.
Thank You!! Fixed my remote. 2000 Buick LeSabre.
Glad it helped, Thanks for Watching.
Lyn Hale Does this work for a 2000 Buick Lsaber even if you don’t have the chip in your key?
Axle's Garage Does this work for a 2000 Buick lesabre even if you don’t have the chip in the key
Do anything additional? I can’t get my 2000 to program.
Thank you Alex i appreciated. So much. You save me some of money
Thanks for watching
Thank you for spend your time to help as.
Thank you so much how does the alarm set
When you lock doors with remote the alarm sets in 30 seconds.
Hello. I am trying to program a brand new replacement key fob for my 2001 Chevy Tahoe. As mentioned the key fob is brand new, with brand new working batteries. I have followed/repeated the entire insert key, hold down unlock button, turn ignition off/on twice, wait for the lock to cycle, press and hold lock/unlock on fob simultaneously. But the lock never cycles therefore the Tahoe never enters programming mode. As a side note, I know that the locks are capable of cycling. Because when I pull and hold the bright light lever while cycling the key twice to program my desired door lock/unlock sequence the locks will actually cycle, the same way that they should when programming the key fobs. Can you please share some troubleshooting steps that might help me diagnose why my Tahoe won't enter programming mode so that I can program my new key fobs? Thank you.
You could have the wrong frequency remotes. If I remember right, there are 2 different frequency ranges.
@@AxlesGarage Getting into programming mode has nothing to so with the new fobs. I have the same problem.
Jonas I have the same problem with my 02 Silverado but my does cycle but when I hold un lock and lock on new key fog it doesn’t cycle there for I can program the new key fobs I don’t know what to do
@@JesusOrtiz-qp1so Found that 07 and later if you dont have the ”i” button and VIC you should out key in acc, not ignition, then hold the odometer stalk in for three seconds until info tells you its ready, do the simultanious unlock/lock on fobs and then turn key off. But if you are sure you get into programming mode ”the old way” you probably have the wrong fobs.
Jones my Silverado is 2002 and yes I’m Able to enter the program the old way but I think your right I think I have the wrong key fob I reach out to the seller and he ask me for the original key fob GM number
Thank you so much for sharing. Worked like a charm!!
Glad we could help. Thanks for watching.
I have a 2006 Chevrolet malibu and I need a key fob for it. Can u give me any suggestions and the programming instructions.
Without at least an old broken original, I don't know how to determine the correct frequency for a replacement. Thanks for watching.
Will this work on a 2005 Chevy SSR 2-door pickup truck.
it may be a hit or miss, I'm not sure. Give it a try and let us know. Thanks for watching
How do you get both clickers programmed?? I got spare programmed then my original wouldn't work. Vice versa. 9nly 1 will program at time. How to do both??
Thumbs up....worked perfect!
Thanks for watching.
will a fob work on my 2017 colorado,it only came with a key
Probably not. Thanks for watching.
Wow!!! I'm so glad for you simple step by step video... It worked!!! My old one would often time lock me out with key's in ignition lol. Be blessed😄
Thanks for watching.
2006 HHR requires use of Tech 2 type scanner, tried many variations of this routine on my HHR LT, but no go. Further reading confirmed 2006 [1st year] needs OBD scanner/programmer
Good info, thanks for watching.
Will it work on a miata
Any help on how I can Connect mine to a 2004 Chevy Impala LS?
This setup might work, give it a try and let us know
Doing this way, will this work on a 2007 chevy 1500 classic truck?
I don't belive so, but it's worth a shot. Thanks for watching.
Will got in my keyless remote and it worked on my 07 chevy classic truck. Thanks for the help!
Do you think it work if just my driver side unlock button doesn’t work?
I should not matter which door lock button you press as long as it's done in the right sequence to enter programming mode. Thanks for Watching.
anyone try this on a 05 chevy equinox??? i’ve been looking everywhere and trying everything
Give it a try and let us know, can't hurt
Does someone know how to unpair it
Axle’s garage would it work on a 2001 camaro?
It should. Can't hurt to try. Thanks for Watching.
I imagine this procedure applies to my 1997 chevy express 5.7 also,right?
97 is a bit earlier, but it may work
Will this work if a Key Remote has already been previously programmed to another vehicle?
Yes
Axle's Garage i have 2001 Malibu. I previously had an 04 Malibu. I tried reprogramming the 04 one to the 01 but i cant.
The are probably using 2 different frequencies. Need to get the part number off the 01 original remote, then put in Amazon search to get the correct aftermarket remote. GM used several different frequencies on the same vehicles and remotes over the years.
will this work on an 03 cadillac seville sls?
It should. Make sure it is the correct remote for the vehicle. That seems to be the biggest problem. Thanks for watching.
Will this work on a 2005 Grand Prix. I have seen other procedures that call for pulling a fuse.
Yes it should
Yes this should work for your vehicle.
UPDATE:
Your vehicle requires that remotes must be programmed by
an automotive locksmith or dealership. There is no way to program
themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and
hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and
tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm
or remote start. These will need to be disabled before new remotes can
be programmed.
It's the carbon buttons behind the keypad that go bad. To avoid dealer or locksmith charges, swap your old PC board into the new remote and no programming needed.There are sellers with just the shell and keypad for $3.00. You can also do a carbon button transplant from a calculator from the dollar store. Use a little silicone adhesive.
Great Tip, Thank You!!!
E visto la mayoria de los video pero no e podido programar el control de una chevy equinox 2006
Glad it helped, Thanks for Watching, but I no Speaky what you speaky
How do you get the unlock button to work. The lock button works on both but not the unlock button.
Maybe reprogram or bad remotes??
Hey Mike I’ve tried this before working like a Charm, BUT today after my last Remote went bad I reordered a new Pair and advanced forward to do the Reprogramming except this time since the remaining defective one can’t work to disable alarm, now when I hold back open door switch then turn key twice, the ALARM turns on loud sounding interrupting the programming process which disallows me to continue wireless auto code insertion codification to accept “auto-key” install validation! How can I BYPASS this dog-gone interference inconvenience? I’m quite anxiously in dismay and annoyed of this inhibition! Please give me another super magic touch method to process key programming! Thanks a bunch of millions for any advice? I’m original owner of GMC 2003 Yukon since then can’t remember the hidden location “secret-button” to disable security alarm system bypass!
That's a tough one, maybe disconnect battery, turn key to on position and reconnect battery
How about getting to the point on programming?
Thank you thank you thank you so much!!!!! Hope you have a blessed day you just made man dude👍🏽👍🏽👍🏽👍🏽
Glad the video helped. Thanks for watching.
The amazon link you provided is for a product that is NOT an OEM GM part. Did you know that?
Yes, they are China knock offs, but they work.
Is that the same way to program a 06 cts?
It might work, give it a try and let us know. Costs nothing to try it.
My 07 Cadillac CTS has driver one and drive her to I love that feature!! I just bought two new remotes off of eBay less than a week ago. Took them to my mechanic, he was able to get one to pair to the car but not the other one. So I got a hold of the seller on eBay and he’s really sending me back half of the money. They must’ve been cheap knock off so I don’t know. I thought I was buying regular GM remote but I guess I didn’t.
Check and see if you didn't get remotes with different frequency. Should be printed somewhere on remote.
Will this work for a 1996 camaro?
It might, worth a shot. Thanks for watching.
I did all you did.. And. It. Not. Program. New remotes. Jut old one.. So what can i do...
Somebody. Told me i need. Disconnected. Battery. For. 30 min. Then do it.... I did still. Not want program. Need help..
Help
You may have a bigger problem with a control module.
Axle's Garage. Help. Can i call you best
Will this work for 2010 Chevy Cobalt?
Cathy Buchholz did you ever figure out how to program it?
Will this work for a 2006 chevy Malibu Maxx?
It might, Give it a try, Nothing to lose. Thanks for watching.
Does it work just to program to use the fob
yes
Will multiple remotes work for one car??
My 2006 equinox doesn't go into program mode when I cycle the key twice. What do I do?
Your vehicle may have another programing method
Thanks so much, do I need a working remote to do this?
No need to have a working remote, that's a Chrysler/Jeep thing.
@@AxlesGarage Thanks, will this work on a 2006 chevy hhr?
Not sure, can't hurt to give it a try
Will this work on a 2009 Chevy cobalt
2009 is too new so, Probably not, but give it a try. Can't hurt.
Did he actually say "because the 'broads' get no. 1"? Definitely an old skool dude.
Yes, Yes I did!
Happy wife, happy life!
That's for sure!!!
You got that right!!
Nelsido Mejia That's how we talk in NY and NJ we call a broad a broad none of that PC crap.
can i program my old 1999 chevy suburban remotes to my 2001 chevy tahoe???
Only if they run the same frequency. Thanks for watching.
How about for a 2006 Pontiac G6? Please somebody help ASAP
Did you get an answer yet?
Does this work on 2006 Chevy Equinox?
If your remote looks the same, it should work. Give it a try and let me know. Thanks for watching.
@@AxlesGarage i just bought that key fob,i have a 2005 chevrolet equinox ,i try so many times, it doesn't work,can you help?
I've been trying this on my Chevy equinox 2006 but it's not working...anyone with a suggestion? Thanks
Doesn't work on 06 colorado either, I dont have a door lock and unlock buttons on my doors. How do I do it?
I'll give it a shot ... broads are always number one!
Yep, thanks for watching
Will this work for a 2005 Buick Terrazza
It might, give it a shot. Nothing to lose. Let us know
Would this work for a 2003 Cadillac CTS
It is possible. Give it a try and let us know. Nothing to Lose.
If you just want to fix it and not pay for a new one you can do it right now. It's easy. I have an 06 Chevy Cobalt. I bought it brand new. I still have the original remotes. Fixed them once or twice.
Thanks for watching
Thank you for making this video.
Glad it helped, thanks for watching.
It works for saturn ion?
Probably not
What if you don't have a lock/unlock button on the doors?
Year make and model?
its a 2009 Pontiac G3. but I found out that you need a special kit to do it or something like that. only a dealership can do it
Yep, 2009 requires a dealer computer
Thanks, it w irk on my 04envoy. I purchase the remote on eBay for about $9.
Glad I could help, Thanks for Watching.
what about a 98 cavalier?
No it will not:
Step-by-Step How To Programming Instructions:
Access programming connector in
left-hand (LH) side of trunk (Driver’s side). You may have to pull back
some trim or carpet to access the programming connector. It will have a
plug on the end of it with two ports.
Use a paperclip or similar conductive
wire to jump programming connector and connect the two ports. Be sure
you are making contact with the metal inside both ports.
System should now lock and unlock doors and activate trunk release to indicate successful entry into programming mode.
Press and hold Lock and Unlock buttons at the same time for up to 15
seconds.
System should now lock and unlock doors and activate trunk
release to indicate successful programming of remote.
Repeat Step 4 for each additional remote to be programmed.
To exit programming mode remove jumper wire.
Test all remotes.
Programming is now complete.
I have an 03 Trailblazer and this did not work for me. It goes into programming mode and then immediately comes out of programming mode
This is the proper method for your vehicle.
My remote blinks when I hit any button. But it won’t program and lock and unlock. Any tips?
Year, Make, and Model??
Axle's Garage 2004 Chevy trailblazer
OK, your procedure should be the same. I am a bit confused about what exactly is blinking? If your vehicle is flashing the lights when you hit the button but the door locks are not operating. Try disconnecting the battery overnight and reprogram. If that does not work, you may have an issue with a body control module or a bad remote.
Axle's Garage the program button that’s built into my antenna blinks. The remote blinks red when I press a button but it does nothing. Can’t access program mode.
Axle's Garage mine has a code alarm system. But your way works but when I press my remote it doesn’t work. Bad remote?
Thanks great infor..
Glad it helped, thanks for watching.
I want my 1966 Chevy II back.
Me Too, Thanks for watching
me too
Very Very good thanks
You're most welcome!
i swear i had to look away when he just stared in the camera
Teyie Miychelle
LMAO my God, that's so fucking funny because I actually read your comment before it he did it, which made it even funnier...OMG he looks like a straight up creeper!
Bahahhaha i thought he could tell what i done the night before!! i was like fuck it and watched a less intimidating video
I read your comment first. 😂 funny shit 😂🤣
Not happening on Chevrolet Cavalier 2004
How to do this?
Awesome video and I agree women are broads!
Thanks
Can someone tell me how to program my 2006 Pontiac G6 key fob please
Maybe someone will chime in...did you try the method in the video?
@@AxlesGarage I did, I watched so many videos on UA-cam but no one worked!
Gezzz can we get to the point!
No, I talk tooooo much. Thanks for watching.
My car doesn't unlock and lock after I do the on off on off
Then it's not entering programming mode. Something is not working correctly. Thanks for Watching.
Didn't work for my 06 Lacross. Held down the unlock button, popped my trunk that was it
Thanks for the reply
does it make coffee yet good program guy....
Coffee... soon.
dosent work when i try to program fey fob
Could be an issue with the vehicle not going in to programming mode
How about crv 2003
no probably not. Thanks for watching
This procedure Will not work on my 2007 Chevrolet Uplander
Thanks for watching.
The 212 that didn't like this video are most likely the people at the dealerships that's not going to make that 2 to 3 hundred dollars programming your key fob.
yep. Thanks for watching
doesnt work for cadillac cts 05
Thanks for the updated info.
starts in 3:16
Yep, I talk a lot.
Broads get #1
They always do
When he finally gets to it...
Worth the wait
Didn't work for a 2002 Chevy Malibu
I'm surprised.
Did not work on 2005 buick lesabre
Thanks for the update
Mines not working at all
Usually, new battery and reprogram. If not get a new remote, make sure the FCC number is the same as your old one and reprogram.