Благодарю автора за видео 👍 Только ребят, совет вам такой, то что автор тянет и выдергивает беспощадно руками, снимайте и поддевайте аккуратно лопаткой. Все снимается гораздо легче если все сделать аккуратно и правильно
Removing the right part of the display by pulling it is really hard (not shown on the video). One easy way to do it is to insert a long zip tie from above the display and grabbing it below, use the wall of the console to direct it, then just pull the zip tie towards you. I wished I had came up with this 1h earlier and without getting my fingers all bloody near the nails.
Вчера проделал всю эту процедуру, теперь всё в порядке, спасибо большое вам за подробное видео. Проблема была когда вытаскивал правый край табло, чуть не сломал, но обошлось.
Thanks for the clear instruction/demonstration on how to get the clock out! With mine all I did was clean up all the terminals and connections on the circuit board with white spirit on a cotton bud, worked fine after.
Yes but I think reheating the points would give a permanent solution for this problem. I have done this a couple of years ago and never seen that problem again.
Благодарю автора за видео 👍
Только ребят, совет вам такой, то что автор тянет и выдергивает беспощадно руками, снимайте и поддевайте аккуратно лопаткой. Все снимается гораздо легче если все сделать аккуратно и правильно
Removing the right part of the display by pulling it is really hard (not shown on the video).
One easy way to do it is to insert a long zip tie from above the display and grabbing it below, use the wall of the console to direct it, then just pull the zip tie towards you.
I wished I had came up with this 1h earlier and without getting my fingers all bloody near the nails.
Вчера проделал всю эту процедуру, теперь всё в порядке, спасибо большое вам за подробное видео. Проблема была когда вытаскивал правый край табло, чуть не сломал, но обошлось.
Thanks for the clear instruction/demonstration on how to get the clock out!
With mine all I did was clean up all the terminals and connections on the circuit board with white spirit on a cotton bud, worked fine after.
Yes but I think reheating the points would give a permanent solution for this problem. I have done this a couple of years ago and never seen that problem again.
Well-done youngman
I was suffering too much
So the problem is a dry joint
Because l always beat my dashboard for that screen to display properly
Thank you for making this. You're a legend.
Sehr gute Aufnahmen und Erklärung. TOP😀
Спасибо автору, очень помогло это видео 😊
So nice tutorial Sir, thanks for sharing.
Explained very well
Excellent! Thank you!
Dziękuję. Bardzo przystępne wideo z demontażu
Спасибо за видео!! супер. помогло.
Снять эту крышку ещё то удовольствие
Thanks 😅😅🎉
Бомба!
Merci
Скажите, а если не полностью цифры и буквы показывает, тоже пропаять?
СПОСИБО
How about speedometer i have 888 problem. Sometimes it show speed fine but moat of times 888. Can i solve problem same?
what to lubricate the places where the plastics join the dashboard. What kind of grease is it?
Goose
Jaka moc ile ustawić do lutowania ?
Так контакты просто прогреть надо? Стобы не растопились
When will a new tutorial be released?
Hi. What tutorial would you like?
Машина хорошая , но вот дрочня с креплениями и постоянно перегорающими лампами ....это ахтунг