Really enjoyed that video. Not too many folks can pull of a video without narration in my opinion. You chose the right shots and kept the angles interesting. Great job. Subbed.
It depends which machine you are referring to, as I have an AVID CNC, and an Axiom. The video you posted in highlights the Axiom CNC. The touch off holder was fabricated on the CNC and the emergency stop is part of the electronics cabinet. If you are referring to the orange ones, I 3D printed them from .STL files I got on thingiverse.
Not quite sure I understand your question entirely but when I am cutting the union the bit is at 18,000 RMP and feed rate is roughly 40 IMP. The values used are those recommended by the manufacturer, in this case Amana.
Very nice video Russ. It would be nice to see a good photo of the finished product at the end. I’m also curious as to where you found the “vertical” hold downs a supposed to the traditional hold downs. I’m using a Laguna IQ...appears to be very similar to the Axiom. Thanks.
jbn0613 the red hold downs you see were ordered with my CNC manufacturer, Axiom. They are just T-track clamps. If you want to see some examples of my finished flags go go my website at: bluelinewoodflags.com. Hope that answers your questions! Stay tuned for a new video of my work flow. It has changed a bit.
Actually in this video I’m using a 30 degree engraving v-bit, 1/4” shank, for the small detail. I get all my bits direct from ToolsToday.com. They are Amana brand bits. I don’t order them from amazon.
Those are hands down the best quality I have seen yet. Very well done. If I wanted to make a smaller version on my CNC, say around 12" wide x 22" long out of 4/4 red oak, would you suggest cutting the panels into 2-3 strips or just find a piece that is at least 12" wide? I have seen some 14 plus inch wide pieces and was thinking that would be nice to have consistent grain but I am afraid a board that wide might warp or cup. I am new to the world of CNC so just wondering what would work best. keep up the great work.
What is your carving time for this flag using the Axiom? I use a homebuilt 2x4 with brushless and a couple of Carvewrights, but I am looking for a faster solution. Thanks
Excluding collet and bit changes, this cut time was around 40 minutes as I recall. This was a first generation flag and since then my flags have gotten much more complex and detailed. Total cut times now range from about an hour to an hour and a half.
I just started my journey of looking into a cnc machine so if you had any recommendations for the beginner wood worker with equipment. I saw a Piranha that was fairly small in the $1400 range which would get a man started but it looks like I'd have to spend about 3K for a Shark model capable of larger material. They had a couple Axioms at Woodcraft for upwards to 8K. Any tips? Your flag project is spectacular. Thanks
With CNC machines you get what you pay for IMHO. I would recommend spending the most you can afford. It sucks to get something you grow out of so quickly. There is a bit of a learning curve with all that is involved. You WILL get frustrated but don’t give up! For tools it all depend on what you want to do. You can keep it simple or go crazy. Good luck!
Patrick Emond my go to bit for the detail work is an Amana RC-1045, 45 degree v bit. I usually use it on a profile tool path for simple linear vectors and set the cut depth to about .025”. Cheers!
Would you consider selling your vcarve file? I am just learning and would be interested in using it for reference. I completely understand if not. There are others I can learn from but yours has so many different tool paths and bits it would be a great learning file. Thanks for considering.
Unfortunately I do not sell my graphic files or designs/tool paths created within VCarvePro. I would suggest you check out my other video “creating a CNC project from start to finish”. I think you will get some good info from it. Also, be sure to check out Mark Lindsay CNC, as he is an awesome teacher for everything CNC. Don’t be discouraged, as there is a learning curve to this stuff. Feel free to email me at russ.tyndall@gmail.com and I will do my best to answer any questions that may pop up. 😀
Marshall CNC sells everything you would ever want on Etsy. Very reasonable prices and 3-4 different file extensions for each file including the CRV file for vcarve desktop/pro
Wood is S3S in various widths and is obtained from a local hardwood supplier here in my home town. I do all my own fitting with a planer and jointer. All boards are edge glued using parallel clamps and cut to final size on the table saw. Lastly, they go through the drum sander. I have an updated video on how I make them on my channel.
Thanks for sharing your workflow - beautiful flags!
Really enjoyed that video. Not too many folks can pull of a video without narration in my opinion. You chose the right shots and kept the angles interesting. Great job. Subbed.
Thanks so much! That was one of my first vids. Appreciate the sub.
Hello, love your flags. I was wondering, where did you get your emergency stop holder and your touch off holder? Thanks
It depends which machine you are referring to, as I have an AVID CNC, and an Axiom. The video you posted in highlights the Axiom CNC. The touch off holder was fabricated on the CNC and the emergency stop is part of the electronics cabinet. If you are referring to the orange ones, I 3D printed them from .STL files I got on thingiverse.
I am looking for a cord style with v-shaped flags for decoration
When doing the union, what are you using for feed and pass rate? Do you go with equal values?
Not quite sure I understand your question entirely but when I am cutting the union the bit is at 18,000 RMP and feed rate is roughly 40 IMP. The values used are those recommended by the manufacturer, in this case Amana.
Very nice video Russ. It would be nice to see a good photo of the finished product at the end. I’m also curious as to where you found the “vertical” hold downs a supposed to the traditional hold downs. I’m using a Laguna IQ...appears to be very similar to the Axiom. Thanks.
jbn0613 the red hold downs you see were ordered with my CNC manufacturer, Axiom. They are just T-track clamps. If you want to see some examples of my finished flags go go my website at: bluelinewoodflags.com. Hope that answers your questions! Stay tuned for a new video of my work flow. It has changed a bit.
Great video. Question... What is the depth you use to carve out the patch center below the department name? thanks
Hi Greg. The depth on that patch center detail was 1/16” using a 30 degree V-bit on a profile cut tool path. Hope that helps you!
What kind of tool path and bit do you use for the state seal? Thank you for sharing this video.
That was a profile tool path cut with a 30 degree engraving v-bit. I use 45 degree bits now and get better results.
Great video what end mill are you using for the stripes
also are you using a 20 degree conical or 15 degree for the small stuff on the shield maybe you could share were you get your bits from amazon?
1/2” downcut end mill
Actually in this video I’m using a 30 degree engraving v-bit, 1/4” shank, for the small detail. I get all my bits direct from ToolsToday.com. They are Amana brand bits. I don’t order them from amazon.
@@BlueLineCNC Thank you I am designing my flag in blender and also the Maltese Cross. but Great work like the videos
What depth do you carve your strips
The stripes are milled to a depth of 1/16".
Those are hands down the best quality I have seen yet. Very well done. If I wanted to make a smaller version on my CNC, say around 12" wide x 22" long out of 4/4 red oak, would you suggest cutting the panels into 2-3 strips or just find a piece that is at least 12" wide? I have seen some 14 plus inch wide pieces and was thinking that would be nice to have consistent grain but I am afraid a board that wide might warp or cup. I am new to the world of CNC so just wondering what would work best. keep up the great work.
I would suggest cutting down and edge gluing. Flip your boards. You’ll have a real solid piece. The glue is actually stronger than the wood.
What is your carving time for this flag using the Axiom? I use a homebuilt 2x4 with brushless and a couple of Carvewrights, but I am looking for a faster solution. Thanks
Excluding collet and bit changes, this cut time was around 40 minutes as I recall. This was a first generation flag and since then my flags have gotten much more complex and detailed. Total cut times now range from about an hour to an hour and a half.
Cool design.
Thanks!
I just started my journey of looking into a cnc machine so if you had any recommendations for the beginner wood worker with equipment. I saw a Piranha that was fairly small in the $1400 range which would get a man started but it looks like I'd have to spend about 3K for a Shark model capable of larger material. They had a couple Axioms at Woodcraft for upwards to 8K. Any tips? Your flag project is spectacular. Thanks
With CNC machines you get what you pay for IMHO. I would recommend spending the most you can afford. It sucks to get something you grow out of so quickly. There is a bit of a learning curve with all that is involved. You WILL get frustrated but don’t give up! For tools it all depend on what you want to do. You can keep it simple or go crazy. Good luck!
This is essentially what I do. What bits do you prefer to do the small detail work?
Patrick Emond my go to bit for the detail work is an Amana RC-1045, 45 degree v bit. I usually use it on a profile tool path for simple linear vectors and set the cut depth to about .025”. Cheers!
@@BlueLineCNC thanks! Great info!
Would you consider selling your vcarve file? I am just learning and would be interested in using it for reference. I completely understand if not. There are others I can learn from but yours has so many different tool paths and bits it would be a great learning file. Thanks for considering.
Unfortunately I do not sell my graphic files or designs/tool paths created within VCarvePro. I would suggest you check out my other video “creating a CNC project from start to finish”. I think you will get some good info from it. Also, be sure to check out Mark Lindsay CNC, as he is an awesome teacher for everything CNC. Don’t be discouraged, as there is a learning curve to this stuff. Feel free to email me at russ.tyndall@gmail.com and I will do my best to answer any questions that may pop up. 😀
Marshall CNC sells everything you would ever want on Etsy. Very reasonable prices and 3-4 different file extensions for each file including the CRV file for vcarve desktop/pro
What do you charge for a flag like this?
Feel free to check out pricing at bluelinewoodflags.com
Where do you get your wood stock from? They look like preglued panels
Wood is S3S in various widths and is obtained from a local hardwood supplier here in my home town. I do all my own fitting with a planer and jointer. All boards are edge glued using parallel clamps and cut to final size on the table saw. Lastly, they go through the drum sander. I have an updated video on how I make them on my channel.
@@BlueLineCNC Can you link this video? I don't see it on your channel.