Replace Backlight LEDs on Samsung Curved 55” for $30 (UN55NU7300 / UN55NU7100 dim screen)
Вставка
- Опубліковано 8 гру 2020
- Today, I show how to fix a Samsung TV with dark / dim screen. I have this curved TV where the left side went dark (well, 90% was dark). Went in with some fresh LEDs and it looks better. Would like to share what I learned along the way too.
NOTE: On the burned plexiglass, it's best to sand down / dremel the burned areas until they're gone, and then reinstall it into the TV the same way. The way the plexiglass is made, it's supposed to darken the section closest to the LED and brighten the section away from the LED. It should be installed the same way, not flipped.
Screwdriver set: amzn.to/2OiNf6v
Plastic Putty Knife: amzn.to/3rfUGtQ
LED Lights: ebay.us/scXAT3 OR amzn.to/3bcFp7q
UN55NU7200 UN55NU6950 UE55NU7120 UN55NU7300 UE55NU7105 55NU710C UE55NU7170U UE55NU7300U HG55NJ678UFXZA UE55NU7400
#samsungtv #tvrepair #brokenscreen - Наука та технологія
On the burned plexiglass at 5:32, it's best to sand down / dremel the burned areas until they're gone, and then reinstall it into the TV the same way. The way the plexiglass is made, it's supposed to darken the section closest to the LED and brighten the section away from the LED. It should be installed the same way, so avoid flipping it as I mention in the video. If you do not dremel down the burned areas, TV will appear yellow like at 9:40.
1. TV LEDs can be purchased here! ebay.us/KQqhgg
2. Screwdriver set: amzn.to/2OiNf6v
3. Plastic Putty Knife: amzn.to/3rfUGtQ
4. LED Lights: ebay.us/scXAT3 OR amzn.to/3bcFp7q
The dremel trick might reduce the yellowing of the picture, but the cracks will still show, so it's not worth the effort. Really, the diffuser should be replaced, if it could be found.
I have the UN55HU7200F ( not the NU in the middle like yours ), same backlight as in yours or is it a full array?
@@kriswingert1662 HU has many more backlights www.ebay.com/itm/203105953105
@@EdwardInTX I have the Samsung UN55NU7300FXZA. As with your's in the video, my plexiglass is cracked and the inner white panel next to it had LED heat damage. Smelled, LOL!!! I got it fixed and it is watchable but the cracks and heat damage do show on the bottom. Can those parts be found at a reasonable cost. Now that I know how, it'd be an easier task. Best advice I can give to others about doing your own repair is to have and use patience and a small and thin straight blade screw driver to remove the white inner frame and twist at the tabs just enough to clear the lock points. My only left over parts were the few I broke and then thought about the smaller screw driver and that worked. But I also slowed down the process. Great video. Thanks Edward.
You really oughta add to the video itself about this. No one is going to look at the comments until after they have problems from following your advice. You can add audio, video or just captions but you're garnering a lot of ill will by leaving it up as is.
Thanks a lot for you and all the other youtubers. I managed to watch these videos and fix my TV for just 1/10th of the repair cost.
I took mine for repairs and they told me it’s the screen so I returned it back home… Thank you very much 🙏 now I can fix mine💪🙏🙏
We followed your guide and were able to fix the tv so that it was watchable again but it was far more difficult for us noobs than it seemed in the video. Many of the little plastic tabs broke and a small chunk of the bezel broke, etc. The one issue that we have now is that when we turned it back on and could see the screen, the picture looks like its being viewed on say.. something like cardboard or some other sort of material and on the far right side, there's an inch where the picture stops instead of going to full side. We obviously messed something up in putting it back together and the two that helped aren't interested in repeating the pull apart process because it was such a hassle for us. No matter what though, the good news is that the process you demonstrated worked and we can now see the full screen. Whatever caused the other issues was something we somehow did. Thank you for the video.
Most detailed and comprehensive tv repair vlog I've ever seen, there isn't anything better than this, more power to you my friend.
Thank you!
Few tips for anybody giving it a go:
1) when you get to remove the LCD panel I found if you very carefully slide a bed sheet) or something similar) under the panel you can easily slide the panel from the base without damaging it.
2) tape the 2 white sheets under the (LCD Panel) together so you don’t lose their orientation/order.
3)do the same for the plexiglass and white backing as it is KEY this goes in the correct way or light will not amit correctly.
4) make sure the white frame clips securing the felxiglass are fixed in correctly. (I made this mistake and I had a lot of LED bleed along the bottom edge just from 2 clips not in correctly)
5) if you put it all back together and the bottom of the screen is very light and top very dim. Your Felxiglass is upside down. Unfortunately you have to take it all apart again and turn it so the top edge is at the bottom. Trust me it a lot easier to take apart the second time. ( you can also plug the tv in with just the plexiglass clipped in to see if the light is covering the entire panel. Instead of reassembling the whole tv to find it's not).
But Thanks Man what a helpful video! Wouldn’t have tried doing this myself if I didn’t watch it and now have a good as new working TV!
Excellent tips!
I'm having the opposite effect of the bottom portion being bright but the the middle and top being very dim.
This walkthru guided me thru the entire process on a 7100fxza that was given to me for free! It is working good as new! 🙌🙏 Thank you SO much!
woohoo!
Fixed the family TV and saved 70% of the TV's cost (what their asking for repairs) THANKS!!!
I used your tutorial on my flat screen Samsung UN50NU7200. The components are exactly the same, except it doesn't have the white tabs securing the metal strip. Unfortunately, I hadn't read your comment about the plexiglass orientation and that dark-on-bottom/light-on-top thing, so I'll be re-doing it tomorrow. For now, the light strips are working great. Thank you so very much for a great video!
Awesome! Hope the reinstall goes well!
Hey, thanks a lot for the guide. Based on your video I successfully repaired slightly different model (6 series instead of 7). While there were some differences your video was a great start.
Now I just hope those "original" led strips from AliExpress won't die after 2 weeks
Very nice! I've done a handful of 6 series the same way!
Thanks for the useful video. Fixed mine 55" in 45 minutes. Big up 👍
Nice!!!
Was it the same model he did in the video??
@@michaelstark9939 Mine was UA55NU7090 .
Thanks, it was very useful, guided me to replace mine, too.
Hi, i just want to say thank you for the video. It was perfect to follow. Ive replaced LEDs on my TV and saved myself £££ buying new one. Only cost me a £10 for 2 LEDs strips from Ali Express. Bonus! Thanks again.
awesome!!
it is great to watch this one even a fresher can do this thanks for the well narrated video....
Thank you!
Hi, just came across your video, it's brilliant this is what i was looking for it was a BIG help thanks .
awesome!
Great job! Now I can tackle mine!
Fantastic video - thanks! My son and I had a great afternoon project and the TV is working beautifully. Had a minor panic when we turned it on and the screen was black. Realised we hadn’t connected the ribbon cables correctly so pulled it apart and reseated them. That fixed it and our heart rates returned to normal
very cool!
I'm having the black screen issue as well but reseating the ribbon cable hasn't fixed it.
@@reallaknight503If the screen is black then it means that the signal isn't getting from the board to the screen. I'd double check the seating of the ribbon cable, I found it a little tricky to get it seated right. If that still doesn't work, check the other end of the cable and if that still doesn't work, check to see that there's power getting to the boards.
Thanks great video having the same problem with the same model now I know what to get and how to fix
awesome!
I did this repair and everything went well following your instructions. I also had a crack in my plexiglass but unfortunately flipping it around created a big shadowed area in upper portion of the screen. Just had to install it the way it was and all is well!! Thank you very much for this video!! 👏🙏
Awesome!!
Because maybe yours contain mirror sheet and u didnt flip the mirror sheet that reflect light some of those have this type of sheet that u must flip them
@@StAlKeRsification Things woodworkers don't know! 🤣 Thanks for the solid info.
@@tecc8380 im a mechanic but i know basic electronics
@@StAlKeRsification So you are gonna use your "intelligence" to generate a negative vibration and judge your own kind? You are aware that people know different things, right?
Very good video. Thanks for your help
Just thank you man, ur a money saver
you're welcome!
This was a good video. I have the same problem with my backlight in my UN48js9000f. I’m gonna attempt your method. Pray for me
good luck!
Thanks.
How to remove LED strips from base?
Mine LED's are glued so hard screwdriver trick isn't for it.
Any other tricks? Maybe some liquid tp desolve or heathing it up?
This is useful stuff. I always wondered how to fix screens like this
Now YOU can do it!
nice video, quick question tho, i have a samsung UE43NU7199 with the exact same problem but i can't find any backlights on ebay for that exact serial number, will any 43" samsung backlights work? or the ones from the NU7100 series maybe? please help
Same problem with my tv thank you for your video
Good luck with the fix!
Thank you for your nice video
Great video, unfortunately I haven’t made it past the fifth minute I have already crack the panel really badly which is a shame I was really excited to fix this tv since I liked it more than the replacement they sent me. It is a great tv such a shame that it breaks just by looking at it.
Excellent very informative...
Are the backlight LEDs for ue55nu7100k and ue55nu7100 the same?
Thank you. And, Subscribed 😊
Hi Edward i changed the backlight and everything is ok except there is a bright spot in the middle bottom abit...what is the possible causes ya?
Amigo buen video nomas q el problema es q el difusor esta al reves por eso se ve asi y solo se puede poner de una pocicion si lo volteas la luz no sera pareja hay q cambiar difusor
Hello 👋, I did this repair on my tv the only issues is the top of the tv is not bright enough , bottom lighting is perfect just top half what issue could I have ?
Near my entertainment center I have always kept a filtered 12x12 box fan , I've never had anything ever go out on me because of this .
Started when I was young I got to have my box fan near me and as I learned heat was the main failure of electronics and noticable heat coming from tv, computer, Xbox and or surround sound.
Thanks very much, I used this video to fix my own issue, sadly, as careful as I tried to be I cracked the screen. Knew it was over but decided to carry on anyway. Anyone thinking about doing this, please be so careful. I barely moved the screen and it cracked. On the bright side I've just ordered a 70 inch ambient light Philips. 😁
This is why I am having a professional fix my TV. I would break something if I tried to do it.
@@fidelbanuelos9601 buy two suction cup thingys and its easy...my dumbass cousin lifted the corner as I was unpacking my suction cups and cracked the fuck out of my top left corner almost to the top middle of the screen...so other than that it's surprisingly easy to do in less than an hour, just use suction on the main screen
@@Beast-mf7br I used paper packing tape instead of suction cups- worked great and left no glue marks
hi can you share to where i can buy LED strips fir Samsung TV 55inch curved model UA55H6800? please share the link online shop 🙏. i am from Indonesia difficult to get that part localy 🙏
Kinda helpful tutorial, coz my Samsung Curved TV (UA49KU6300G) has a vertical lines and some black spots on the screen. Im just assuming it has the same teardown process and im gonna try it now. Thankyou for uploading this.
How it go
Can you pls tell me if my model is au55nu7300g. can i use au55nu7300k backlight??
Is Un55ku6500 similar I have image but I'm getting white spots why idea what that is?
Did mine today, $32 for LEDs off EBay, made sure that part number matched up with samsung part. 2 hours to do complete disassembly, fix and reassemble.
Very cool!
Thank you, my tv like this problem
Thank you just fixed mines
Great!
thanks for showing the led strip change. do you suggest to fix the vertical shadow on the screen by changing the led strip ? will it help? Also could you pls suggest the led strip for the curved samsung UN55KU7500 model.
Yes, you'd need to change the LED strip to fix the vertical shadow. This is for the KU7500, but the led strip installation process will look different from the video as the LED are scattered across the screen. www.ebay.com/itm/154951141781?hash=item2413cec995%3Ag%3AeFcAAOSwLateeccK&amdata=enc%3AAQAHAAAAkMSl1Ks%2BPSe9V5Ol0qrJlK02c0N1Sxp5csU25%2BxOlb9DWYDGpJqQ9wH%2FylpV9uLs8T5yJCVE27ttIBryoHdMYyBFYscUxyHiyEetpCtle5YQ6X0ephVN92y84wjrQWArBvV6Xx%2B5MKh4FpNztva0GIMzJ%2Bhld8ana9B8Ko9bJAOQYel%2FuHkiMZCPfX2AExF4Ow%3D%3D&mkcid=1&mkrid=711-53200-19255-0&siteid=0&campid=5338782093&customid=&toolid=10001&mkevt=1
I have a curved on different model it turns on go's to a blue screen then shuts off my electronic mentor says it's probably a resistor on the power supply. Dose that sound right? Mine is a Samsung UN65KU650DFXZA
Hi now i have no image but both side led work and sound work help me please
Followed the tutorial damaged my tv thank you.
Thank you for this video.
This was super helpful, however I had 2 issues. In taking off the black front enclosure I snapped two clips because I started on the bottom. Starting on the sides and top seems to make the bottom clips easier to get out.
Second, there was some burn on the inside, so I rotated things like you mentioned, but now the bottom of the screen is extremely bright compared to the top. I don't want to take the screen apart more than once more because of the aforementioned snapped clips, so I need to figure out whether I need to push all the interior panels and sheets as far to the bottom as possible (they oddly don't all fit exactly with the screen size by a few millimetres and may not be sitting flush with the bottom, which might be the issue) or I need to just put things back like they were with the slightly burned panel (might see if I can clean off some of the brown, as the burn isn't as bad as yours). Any ideas?
On number 2, you are correct. I pinned my other comment hoping people would see it. On the burned plexiglass, I've found it's best to sand down / dremel the burned areas until they're gone, and then reinstall it into the TV the same way. The way the plexiglass is made, it's supposed to darken the section closest to the LED and brighten the section away from the LED. It should be installed the same way, not flipped.
@@EdwardInTX You should add this info you the video description. I looked there before I looked at the comments, but I didn't see which ever one you pinned.
@@ashbradford Just did. Thank you!
Hi. I find your videos really helpful. Is it going to be the same process for Samsung Ua43nu7100? Your response will mean so much. Thanks! 🙂
yes it should!
thanks a lot from the Phil,
Did repositioning that paper help with the back light bleed? I have the same issue after replacing the LEDs. I hate opening up this TV lol
The burnt panel had to be installed the same way it came out. Can't flip it. The trick with that panel is the burned areas need to be completely dremeled off.
After attempting the repair about 25% of my screen (bottom half) is bright while the rest of 75% is a bit dim. I read someone else posted the same issue about a year ago
Hey guys jus looking for some help
3 mths ago a technician supposedly replaced the strips on my samsung 43 inch smart tv.
Problem has now risen again as i have no light on screen but can hear sounds and see images if i shine a light on it.
Tv power light blinks 5 times when turned on. Didnt find much help on the web
Great video. I have one now that needs the repair. Could I put do anything such as adding thermal paste to help prevent over heating again?
Some people mention adding a capacitor to regulate the LEDs but I’m not that advanced
@@EdwardInTX i have the same problem on my samsung..
Really refuse to send it back for repairs for hundreds of dollars so i might try it myself
I’m just wondering how old was this particular tv? Screens nowadays seem to last like a year or 2 until they get this
Great video though!
@@mrcreeperman13 this was either 2017 or 2018. It was the 4th 7 series samsung I fixed.
Richard Dolesh una pregunta este tv trae salida de Bluetooth ?
Would this process be the same for all newer Samsung tvs? I have a UN58RU7100
yes it works for that model
Excellent Video! Thank you for posting!! Let me ask you this.... Why is it that just about everything Samsung makes, turns out to be absolute crap!?? We purchased all new higher end Samsung black stainless appliances in 2018. In the first year the microwave failed twice. The oven part of the range failed twice, the fridge ice maker froze over daily and stopped producing ice. The metal finish is so thin that it dents with almost no pressure. Now our 2 year old 75" OLED backlight has failed on the right side. I WILL NEVER BUY ANOTHER SAMSUNG PRODUCT EVER AGAIN.
Wow this is terrible! I have a samsung microwave and range and they haven't failed (knock on wood)
Great video! I can’t seem to find a strip for mine. It’s a un55ku7500f model. Are there any other LED strips compatible for my model?
Try ebay,has stripes for all samsung models
@EdwardTX
I own a Gigabyte 32" Monitor G32QC and need to replace one of the light strips as I have a black bar, indicating that one of the backlights is not working. Could you provide the part number or share a link to the backlight strip that would be compatible with my monitor?
did a quick search online, wasn't able to find a replacement LED set for that
thanks
Hey thanks for the walkthrough. I followed your directions and I’m ecstatic that it fixed the issue, but now I have a bad backlight bleed like you described towards the end of your video. I remember I flipped it upside down with the plexiglass. If I disassemble everything, and flip the white sheet back the way it was and leave the plexiglass, will it fix the backlight bleed? Thanks.
Yes, with the caveat being the paper has to be really flat to even the light out properly (caveat: the curved tvs are much harder to straighten than that flat panel)
Thanks, I have it apart again and I can’t tell if I have it right and I really don’t want to take it a part again. lol
I Would have liked a few shots of the whole back of the tv, can you confirm what boards are they, main board, power board etc?. Before I dismantle ours I am wondering if it is worth it cost wise. Ours went bang & I would like to replace all boards as I suspect the power board took them all out?.
9:18 - 9:26 show the main board (green) and power board (brown). Those are the two main ones. If either of those don't fix it, there's a deeper problem in the panel that isn't worth fixing.
you needed only two led strips for lower edge ? no need for upper edge ? thank you advance.
correct, due to how they made the plexiglass
Very good video, but I have had a problem, trying to disassemble it the panel had cracked and I cannot find the replacement. any help to find it? Thank you!
500 minimum in Canada...prob around 400 if you're lucky in the states...better off buying a new TV...there's a profitable reason why these fuckwad manufacturers make the main screen so fragile!
Great one hand shooting 😀
thanks!
Great video. I just want to ask if the cracks on the plexiglass don't matter because there are quite a few of them.
If there are brownish spots at the end, sand them off. The cracks will show a little brighter than the rest of the screen, but not really bothersome.
@@EdwardInTX OK. Thanks for the reply.
Hey Edward! Thanks for this video, very informative. I'm wondering if these LED lights would work on my tv model; nu55tu8300? -Thanks!
just looked -- yes they would
@@EdwardInTX Thank You Sir!
is there any way i can get spare parts for those boards at 3:55 (i accidentilly fucked up 2 of those yellow ribbon cables.)
Theyre called buffer boards, sometimes they appear on ebay but the connections are so small it can be difficult to reattach/solder
@@EdwardInTX thank you. you absolute legend
I have a cracked and burnt plexiglass just like in your video. Mine is a little worse, but do you know if you can get just the plexiglass? I am not having luck finding. Even Samsung does not have for resale to the end user and no techs within 200 miles
Larry I feel you, man! I've fixed ten Samsung's with edge lighting all with the same problem. I've spent multiple hours looking for a way to purchase the plexiglass diffusor. Still can't find a place so I have to swap them with ones I find from broken screen TVs. Did you ever find a place?
Quick question, are the ribbon cables supposed to go on top or under the pins?
The pins should be touching each other. There are two very little tabs on each side of the part the ribbon cable goes into. Slide it in so they are under those tiny tabs, and pins are facing down. If that doesn't answer your question, I don't quite understand what you are asking.
Chandler is right. Under the pins.
@@ChandlerC11 thanks for the reply. It turns out, that the ribbon cables had nothing to do with it, I just forgot to plug the remote sensor in, so I couldn't turn it on. The tv is good as new now!
I repaired a same 55 Samsung tv like this but i has light bleeding like your tv, you said the problem is the position of tge first white paper.how should i do it on the first white paper to fix light bleeding in the bottom ?
Actually I realized it's because of the transparent plexiglass. The best way is to dremel off the burned parts of it and put it back in the same way.
thank you sir
thanks for stopping by!
They also burn and damage the Diffusers .
I could not find led strips for SAMSUNG ue65js9505 curve TV same as yours, 65" though. Any suggestion!!! By the way, great stuff that you put here, good job.
What country you in ?
@@ImranAli-rp4kd Denmark
My curved samsung tv 32 inches was hit by my son and got broken. Any lead on where i can buy the screen part?
panel isn't sold new, would just recommend buying a new tv unless you can find a similar tv with bad LEDs to swap the panel out
Please what steps should I follow to fix my 55 nu7300 it has a problem with backlight going very dark when I am watching any dark scenes
same as i show in this video
I need the LED for my Samsung UN65JS9500F can you tell me where I can get them? I can't find them anywhere Ebay or Amazon pls help Mr thanks
I couldn't find it either :(
What is the correct position for the bottom sheet to prevent the backlight bleed?
The same way it was taken out. Dremel or shave off any yellowing areas
What about the UN55NU7200F?? And my tv has a 6 inch wide vertical stripe off to the left of the center of the screen.. From what I've read, its just a strip of led's.. I paid close to 900 right before it went on sale so I'm super salty about the price of this tv and needless to say its a sensitive subject.. Anyways, id really like to fix it if I can, so any thoughts??
I just fixed that model NU7200 a few weeks ago. Same process as these.
Hey I have a 65" with this problem but I went ahead and ordered the ones in your description ...did I just mess up????
65 is longer. You'll need other LEDS based on your model.
Thanks man! It helped a lot, after I replaced the back light, the top looks darker than the bottom. Is there a reason why?
The plastic diffuser panel distributes light to make it even. The best remedy is to saw off the burned parts at the true bottom and then reassemble it. Light will be even after that.
@@EdwardInTX I just change the position of the plastic, it looks way better. Thanks man!
@@TheAldoo1995 Excellent!
@@TheAldoo1995 what do u mean you change the position by mounting it upside down?
@@4g63_Everything I think I accidentally changed the plexiglass position. It didn't look as bright as it is supposed to do.
bonjour monsieur nous aimerions avoir Backlight LEDs du modele UE55HU8200LXZF car cela m'est difficile de trouver. un lien ou autre solution pour avoir une piece de rechange merci
This has how many leds? All together
So I accidentally got the ribbon to tear off of the board. Can I solder it back on?
i'm not sure, never tried it. looks possible though but would be careful since the connector is plastic
Dude, I want that couch! LOL
I really wish you showed how to safely move the lcd panel instead of transition to it being done. My brother and I were on the last step of moving the lcd panel back in place with a team lift, only for the screen to crack in the same corner I replaced the broken leds. Now instead of half a screen being black, I have about %96 a screen with a crack in the corner.
How did you move the lcd panel multiple times as one guy without cracking it?
Exactly. My new LEDs are working great, but now the tv is trash because somehow I got a crack through the screen. Tv is trash. I was trying to be so careful and didn't even realize I got crack until I got it all put back together and turned it back on.
Hey,do I need a glass lifter for the screen or do you think it’s safe to grab it by hands
i grabbed it with my hands
Oh ok thanks
What about the 55" Samsung that has leds on the actual panel? What leds do I need to replace then?
What is the model number of the TV?
plexiglass replacement?
I have backlights, but purple and greenish vertical pixels all over it.?
Any tips?
I'm not an expert in this, but it might be a t con ribbon connection, or the main board (if the screen is not cracked)
I just followed your video to successfully replace the backlights on my Samsung 55 inch tv.
But half an hour after watching a bit of tv the newly replaced LED strip burnt out on the same side as it did with the old LED strip.. :(
Any idea why?
omg no! That was a bad LED strip. Request a replacement.
how easily is to break the glass panel? I have to change the LEDs of mine but im scared ill break the glass. And sending it to repair its really expensive
it's quite easy. You have to keep it as flat as you can as I show in this video
I need ur help,how can u help me.
When lifting the panel out of a curved monitor, can I lay that curved panel on a flat surface? Or does the curved panel has to be on a surface of the same curve?
It can be laid on a flat surface.
Btw if you see the burned area at the bottom, I recommend just sanding that down until clear and putting back in the way you found it, due to how it dissipates the light.
@@EdwardInTX Is it possible to buy a new of these burnt/cracked plexiglass pieces?
@@markgarrison9719 doubt it unless you search and call every TV repair place within a 2 continent radius! Lol
anyone know if there are big differences between this model and the un65nu7100 besides the size?
No difference
Hi , I have a little white dot on my samsung tv UE55HU7250 , can you guys give some tips to fix the problem please ?
Oooh that one uses many more LED strips than this model. It could be a panel defect or one LED bulb is out.
My Samsung LED TV has same backlight problem... would you repair it? If u then let me know how much it'll cost? I can't afford to pay more money
Do you have a video to repair the cracked screen
Cracked screens cannot be repaired. You'd have to find a replacement panel.
I believe this is the exact problem I have on my curved samsung. Can you comment on how much I should expect to pay for this to be repaired by a local tv repairman?
I've asked two. They charge $60-100 for labor, and LEDs would be another $30 on top.
Is the backlight strips original? Because I have found 2 strips for 10$ including the shipping from AliExpress and the one you have attached in the description will cost me 50$ including the shipping, so what do you think mr Edward ?
They're not original. The ones I bought were $25-30 on ebay.
@@EdwardInTX unfortunately the ones on ebay are 25$ but the shipping is 30$ so it will cost like 50$, and I’m wondering since it’s not original, do you think that the ones on AliExpress will do it or should I buy the ebay ones ?
@@nawaf8258 I do not know the answer to that question as I've never tried or seen the Aliexpress ones
@@EdwardInTX fair enough, thx alot edward I just wanted to check if it’s original or not.